Advanced Keys AK-104 User manual

ADVANCED KEYS
Smart Keyless Entry System
INSTALLATION GUIDE
AK-104
REV: A05-11-1118
www.advancedkeys.com
[e-mail]
© Copyright Advanced Keys Inc. 2011. All Rights Reserved.
*
ProductFeatures:
•Smart Keyless Locking/Unlocking
•Compact Sized Smart Keys
•Dual-Antenna Setup
•BypassTransponder RFID Cards
•Vehicle Anti-Theft Function
•Ignition Controlled Lock / Unlock
•Auto Vehicle Battery Power Saving
•Door-Not-Closed Reminder
•Smart Key Battery Low Reminder
•Locking-Delay Function
•Compatible with Push-Start Ignition
•Auto Window Closing Output

2© Copyright Advanced Keys Inc. 2011. All Rights Reserved.
TableOf Contents .....................................................................................2
ProductContents ..................................................................................... 2
Warning and Safety Information ............................................................ 3
Safety Precautions ................................................................................3
Pre-installationConsiderations .............................................................3
Connections ............................................................................................... 4
MainHarness Wire Descriptions ..........................................................4
Access Harness Wire Descriptions .....................................................5
ControllerWiring Diagram ....................................................................6
Installation................................................................................................... 7
InstallationOverview .............................................................................7
InstallationNote ....................................................................................7
ProgrammableFeatures ........................................................................7
Antenna Installation ...............................................................................8
Frequent Asked Questions .....................................................................9
SmartKey Programming Procedure .....................................................10
Closing Up ..................................................................................................11
References Information ............................................................................11
Specifications ....................................................................................... 11
ProductRegistration ............................................................................. 11
Warranty ............................................................................................... 12
FCC And Canadian Compliance ..........................................................12
TABLE OF CONTENTS
The following list of components are included in this system:
1 Bypass Antenna
2 Bypass Transponder Card
1 Starter Disable Relay
1 User Manual/Installation Guide
1 Control Unit
2 Smart Key Fob
1 Main Harness (8-Pin)
1 Accessory Harness (7-Pin)
1 Dual Colour LED Indicator
1 Front Antenna Coil
1 Rear Antenna Coil
PRODUCT CONTENTS

3
© Copyright Advanced Keys Inc. 2011. All Rights Reserved.
•This product shall be installed by a certified technician therefore a certain level
of competence and knowledge are therefore assumed when reading this guide.
•This guide is provided as a GENERAL installation instructions and vehicle
subjected to installation maybe different.
•This product is designed based on vehicle regulatory standard. Please observe
your local public road traffic law and regulations prior to installation.
•Exercise due-diligence when installingthis product. The manufacturer and
distributors of this product will not accept any vehicle damage or personal
injury resulting from the installation of this product. Installation of this product is
acceptance of this statement and releases the manufacturer/distributors of this
product from any direct or indirect liabilities.
•Once installation is complete, please return this guide along with other
documentations included in this product back to customer for future reference.
The manufacturer/distributors of this product does not guarantee this particular
version will be available at a later date.
PRODUCTSAFETYAND LEGAL DISCLAIMER
WARNING AND SAFETYINFORMATION
•Carefully read and understand the User Manual, Installation Guide and
Electrical Service Information for the subjected vehicle before begin work.
•Install in a well-lit, dry, covered area away from the elements and keep at least
one window open all time during installation. Do not leave key inside ignition
switch and /or detection range. Prepare all tools required forthe installation.
Special tools maybe necessary depending on vehicle.
•Verify the vehicle hasproper grounding and does not have any outstanding
electrical/functional issue prior to installation.
•To avoid short circuit, it is recommended to pull-out related fuses before
installation and put them back when installation is complete.
•Only locate necessary wires related to the installation (most required wiring are
under driver dash/kick panel areas) andconnect to the unit according to the
wiring diagram. Use a Multimeter to verify and confirm
before connecting or disconnecting. We strictly prohibit testing or modifying
systems.
•Begin function tests on the system after verifying and ensuring all wires have
been connected correctly and insulatedproperly.
PRE-INSTALLATION CONSIDERATIONS
DO NOT power up the module beforeit is properly grounded.
Shouldthe unit be powered beforebeing grounded, serious
damage tointernalcomponentscould occur.
CAUTION

Grey
Grey
Red
Green
Blue
Black
Purple
7.5A
7.5A
15A
15A
15A
Main Harness
8-Pin 18 AWG
Parking Light
Parking Light
Battery +12V
Lock
Unlock
Ground
Horn Control
+
-
+
+
-
-
-
JP3
JP4
Brown Trunk Release
-
Brown
OUTPUT
500mA
Trunk Release
Connectto the negative side of the trunk release trigger. This output will provide 1second pulse
when UNLOCK button is pressed for 2 seconds. (This function is disabled when ACC input is ON)
Grey
OUTPUT
7.5A
Parking Light x2
Connectto the positive side of parking lights or the hazard light switch for same effect.
Red
OUTPUT
15A
Battery +12V
Connectto a +12v source. Ensure that the OEM source wire used is fused for more than15A.
Note: When no suitable +12V source available (where current capacity is less than 15A) use
Green
OUTPUT
15A
Lock
Connectthis output directly to the negative-triggered door lock signal wire.
Blue
OUTPUT
15A
Unlock
Connectthis output directly to a negative-triggered door unlock signal wire.
Note: This system outputs a single unlock pulse by default. Jumper (JP3) provides a double unlock
pulses output option for vehicles that require a two consecutive unlock-pulse to unlock/disarm or to
bypass the Driver Door Priority Unlock function to unlock all doors.
Black
OUTPUT
15A
Ground
Connectedto bare, unpainted metal on chassis. It is recommended to use a factory ground bolt
rather thana self-tapping screw. Screws tend to get loose or rusted over time and lead to erratic
electrical problems.
Purple
OUTPUT
500mA
Horn Control
Connectto the negative side of horn for audio notification.
Note: This system is programmed for muted Lock/Unlock
operation by default. If audio notification is desired for arming
anddisarming; connect Horn Control output to a siren* and
changethejumper setting (JP4) to Siren Output option
(Refer to Horn or Siren Mode in Programmable Features).
Note: If siren control is a positive type or require more than
500mA to operate; add a relay according to the diagram on
theright to convert output to a positive type.
4© Copyright Advanced Keys Inc. 2011. All Rights Reserved.
MAIN HARNESS WIRING DESCRIPTIONS
Wiring Description:
JP1JP2JP3JP4

Negative (-) to Positive (+)
Output Conversion
Horn
Control
Output
(-)
+12V
NO
COM
NC
87
87A
30
85
86
*Siren not included
+
+
JP4
JP3





White
OUTPUT
500mA
Starter Kill Relay Control
(StarterKill Relay is not required if installed with AK-PSB05)
Depending on jumper (JP2) selection this output can be used for:
Starter Kill Relay Control (Default) Alsoknownas Ground-
When-Armed. While armed (Smart Key not detected or LOCK
buttonpressed)this output provides a constant GND to disablethe
startercircuit when an unauthorized ignition is commenced. Connect
theStarter Kill Relay according to the wiring diagram on the right.
Ground-When-Disarmed Provides aGND signalwhile disarmed.
(Smart Key is detected or UNLOCK button pressed)This output can
beused as an enable signalto an immobilizer bypass or known as
Ground-When-Running. Alternatively this output can connect to any
system thatrequires an input signalwhen a Smart Key is sensed.
Purple
OUTPUT
100mA
Push-Start Module Control
EnginePush-StartIgnition Controller.
Thisoutputprovidesanencryptedsignaltothe EnginePush-StartIgnitioncontrolleronlywhen system
sensea validSmartKeyor disarmedvia the UNLOCKbuttonorfrom the BypassTransponderCard.
Brown
INPUT
Brake
Connecttothe brakepedalswitch thatoutput+12v when brake isapplied, GND orfloatwhen released.
Note:Thisinputisrequired forSmart Key programming andIgnition-ControlledLockfunction.
Blue
OUTPUT
100mA
Window Closer Module Control
ConnecttotheoptionalAutoWindowCloserModule triggerinput.
Green
INPUT
Door Switch
-
directly. Change jumper(JP1)to
Positive DoorTriggerif door
switch isa positive-triggered type.
Red
INPUT
ACC
**Required for Remote Start option** This input must be
connected to a +12v source when ignition key is in the ACC
position. Note: With this input active, controller will stop search
for the Smart Keys to conserve battery and avoid
unintendedlockactuationwhile the vehicleisrunning.
Starter
Kill Relay
Control
NO
COM
NC
87
87A
30
85
86
ON
ACC
OFF
START (+)
ENGINE
START
Starter Kill Relay (Included)
5
© Copyright Advanced Keys Inc. 2011. All Rights Reserved.
ACCESSORY HARNESS WIRING DESCRIPTIONS
Wiring Description:
~
JP1
JP2
White
Purple
Brown
Blue
Green
Red
Accessory Harness
7-Pin 22 AWG
Starter Kill Relay Control
Push-Start Module Control
Brake
Window Closer Module Control
Door Switch
ACC
~
-
+
+
-
+
-
JP2
JP1
OPTIONAL
JP1JP2JP3JP4
OPTIONAL
ACC
Input ON
ACC
OFF
START
VEHICLE
CIRCUIT
+12v
Dome
Light Door
Switch
Door
Switch
Input
(Default) Negative Door Trigger (-) Positive Door Trigger (+)
+12v
Dome
Light Door
Switch
Door
Switch
Input
Ensure allconnections arecompleted andproperly secured
prior to connecting the wire harnesses to the module.
+

+


NOTE
REQUIRED

WAR NING: M anuf acturer/Distributors of th is product w ill not be responsible for an y electric al d amage resultin g fro m
improper installation of th is product , be th at either d amage to the vehicle i tself or to the device. This device must be
installed by a certif ied technician for th is guide has been written for properly t rained technicians; a certain level of
skill & knowledge is therefore assumed. Review this installation guide and vehicle's service manuals before install.
CONNECTIONS
CONTROLLER WIRINGDIAGRAM
JP1 JP2 JP3 JP4
Dual Color LED
Bypass Antenna
Rear Antenna (Longer Wire)
Front Antenna
Grey
Grey
Red
Green
Blue
Black
Purple
Main Harness
8-Pin 18 AWG
Parking Light
Parking Light
Battery +12V
Lock
Unlock
Ground
Horn Control
+
-
+
+
-
-
-
White
Purple
Brown
Blue
Green
Red
Accessory Harness
7-Pin 22 AWG
Starter Kill Relay Control
Push-Start Module Control
Brake
Door Switch
ACC
~
-
+
+
-
+
-
Brown Trunk Release
-
Window Closer Module Control
7.5A
7.5A
15A
15A
15A
Default Settings
Optional Settings
Neg.(-) Door Trigger
Pos.(+) Door Trigger
Ground-When-Armed
Ground-When-Disarmed
Single Unlock Pulse
Double Unlock Pulses
OEM Horn Output
Siren Output
+
-
~
Legend:
Input
Output
Positive Type
Negative Type
JP1
JP2
JP3
JP4
FrequencyType
In-Line Fuse
JumperSettings:
JP3
JP4
JP2
JP1
6© Copyright Advanced Keys Inc. 2011. All Rights Reserved.

Reviewproductmanual
manual. Preparevehicle
forinstallation.
Reviewandset
controllerjumper
settingsaccordingto
requirements.
ConnectMainand
AccessoryHarness.
Pre-positionantennas
andantennawiring.
PowerONthe system
andsetprogrammable
features.
Verifysmartkeysand
bypasstranspondercard
function/rangethenroute
andsecure antennasto
finalposition.
MountLED, secure
controllerandclose-up
installation.
INSTALLATION
Use following steps as a guide to install this system:
INSTALLATION NOTES
•For vehicles equipped with factory or aftermarket alarm/remote start, it is
possible to install this system without the anti-theft alarmand remote start
functions. (Refer to User Manual on how to disable Alarm Function) Connect
BATTERY, GROUND, LOCK, UNLOCK, ACC, BRAKE and ANTENNAS for
Smart Keyless Entry function only.
•Ensure the ACC(+) input is connected. It is required for remote-start function
Avoid leavingthe Smart Key inside or near the detection range for extended
periods of time, for it will remain in constant communication with the controller
•It is recommended to connect the DOOR SWITCH input to the vehicle. This
system will have a better remote sensing performance when it is aware of the
door status.
PROGRAMMABLEFEATURES
Horn or Siren Mode locking or
unlocking. Horn output will only sound in alarming and programming mode. If the
Horn Output
Siren Output
Parking Light
Unlock
-
2 x
2 x
Lock
-
1 x
1 x
Remote Start
-
1 x
1 x
INSTALLATION OVERVIEW
7
© Copyright Advanced Keys Inc. 2011. All Rights Reserved.

ANTENNAS INSTALLATION
Antennasshould be mounted on a Non-Enclosed and Non-Metallic material
such as clear glass or plastic trim panels. Recommended placements for the
Front-Antenna is on the top-left corner of the front windshield and bottom-left
corner of the rear windshield for the Rear-Antenna. The Bypass-Antenna can be
placedaround the edge of the front windshield so it can sense the Bypass
Transponder Card within one inch away from outside of the vehicle. Do not place
antenna in locations that will be shield by metallic material.
Test for coverage and range after installation to determine the optimal locations
for the antennas. You may adjust antenna positions to other possible placement
locations asillustrated in the diagram. Use double sided tape to secure antennas
after final positions are confirmed.
Ignition-Controlled Door Lock
Enabled by default and controlled by Brake input, this function will provide:
•Auto Door Locking when ACC is turned ON while brake is applied.
•Auto Door Re-Locking when brake applied after door opened-then-closed.
•Auto Door Unlocking when ACC is OFF.
To disable Ignition-Controlled Door Lock feature, press and hold the brake pedal
when powering ON the controller. Horn output will sound 2x if this feature is
disabled or 1x if this feature enabled.
PROGRAMMABLEFEATURES (CONT.)
Front Antenna
Placement
Rear Antenna
Placement
Main Antennas
5 -6 Feet Range
Bypass Antenna
0.5 -1 Inches Range
Other Possible
Placement Locations
Bypass Antenna
Placement
Antenna needstobe positioned awayfrom any typeof
metallicmaterialtoachievethe best reception in all
directions. Avoid strain/pullon antenna wiringand do
not bendor overlapMainantenna withBypass antenna.
IMPORTANT
8© Copyright Advanced Keys Inc. 2011. All Rights Reserved.

FAQ
Whyis key detection not working or the range is very sort?
Verify antenna position: Antenna may be on or close to metallic material, change
position to verify range sensitivity. Check antenna wiring, do not pull on the
antenna wires, make sure connectors are firmly seated. If remote failed to work
both in proximity and manually press the buttons, follow key programming
procedure to relearn all keys.
What does each LED color status mean?
See User Manual for more information on LED status detail.
How to install this system without the alarm function?
See User Manual for more information on disable alarm function.
How to enable/disable automatic door locking/unlocking function?
-
section to enable/disable this function.
How does Remote Start button on the Smart Key remote work?
Remote Start function require installing the optional Advanced Keys Push-Start
System (AK-PSB05). Press the remote start button will send a remote start
signal to the Push-Start Module via the Push-Start Module Control output. Please
refer to Push-Start Installation manual for more info on remote start the vehicle.

10 © Copyright Advanced Keys Inc. 2011. All Rights Reserved.
If required, use the following procedures to program a new set of Smart Key
and/or Bypass Transponder Cards. Both set of Smart Keys or the Bypass
Transponder Cards must be present and accessible during programming.
Enter Programming Mode
Disarm the system by a valid Smart Key or Bypass Transponder Card. Turn the
Ignition Key to the ACC position. After few seconds switch the Ignition Key to
OFF position and immediately back to ACC position for five times or as following:
OFF ACC OFF ACC OFF ACC OFF ACC OFF ACC. Keep the Ignition
Key in ACC position at the fifth time and the horn will sound twice. (Turn the
Ignition Key to OFF position at any time will exit the programming mode with horn
sound three times)
Smart Key(s) Programming
1. After enter the SmartKey programming mode, LED indicator turns RED. You have
30 seconds windowto program. If you do not wish to program Smart Keys, press
the brake pedal once to skipto BypassTransponder Cardsprogramming (Horn
will sound once to confirm)
2. Press and hold the LOCK button on thefirst SmartKey until horn soundonce.
3. Press and hold the LOCK button on thesecond Smart Keyuntil horn soundonce.
4. Smart Keys programming is nowcompleted. System willautomatically enter
Bypass Transponder Cards programming mode.
Bypass Transponder Cards Programming
1. After enter the BypassTransponder Card programming mode, LED indicator
turns BLUE. You have 12 secondswindowto program. To skip Bypass
Transponder Cardsprogramming, press the brake pedal once will end the
programming mode with horn sound five(5) times.
2. Holdfirst BypassTransponder Cardagainst thereadingfield of the Backup
Antenna until the horn sound once.
3. Repeat for the second Bypass Transponder Card until the horn sound five(5)
times to indicate keyprogramming has been successfully completed.
Note: Only one Bypass Transponder Card should be sensed in the reading field
at a time. The sensing range for the Bypass Antenna is under an inch.
Horn Sound Summary Table
Numberof Horn Sound
Mode Description
1x
Remote/ Key Registered
2x
EnteredProgramming mode
3x
Programmingfailed
5x
Programmingsuccessful
KEYPROGRAMMING PROCEDURE

11
© Copyright Advanced Keys Inc. 2011. All Rights Reserved.
Controlleroperatingvoltage range:.................................................................................... 10VDC 16VDC
ControllerStandbypower:................................................................................................. ≤30mA@12VDC
Avg. controlleroperatingpower: ........................................................................................... ≤80mA@12VDC
Devicesoperatingtemperature range:..................................................................................... -25°C +85°C
Transmitteroperatingvoltage range:...................................................................................... 2VDC 4VDC
TransmitterStandbypower: ................................................................................................... ≤7µA@ 3VDC
HFoperation frequency andrange:............................................................... 433.92MHz @25-30Meters
LFoperationfrequency andrange:.................................................................... 134.2KHz @1.5-2Meters
SmartKeyFobDimensions:................................................................................. 65mmL x44mmWx 6mmH
Base ControllerDimensions:........................................................................... 115mmL x90mmWx 30mmH
Installerofthissystem tois requestedtofill outthe following information asa proofof installation to
the end-userofthissystem. For manufacture warrantytotake immediate effectplease requestthe
end-usertoupdatethefollowinginformationat:http://www.advancedkeys.com/registration.htm
•Connectingthe wireharnessesandpowerONthe controller, checkandconfirmsystemoperations
(RefertoUserManual)thenverifyfunctionsofthe vehicleare inworkingorder.
•Makesure allwiringconnection are insulatedproperly. Placeandsecure controlunitstolocations
inside trim panelsandbundlealllose wiring. Putbackalltrim panels
•When mountingthe controllerunitin the vehicle, considerthe locationcarefully. Youshouldmake
sure thatyou avoidany location where the controllerisexposedtomoisture, extremeheator
interfere with movingpartsonthe vehiclewhich hampersdriving.
•Explainallfunctionsrelatedtothe end-userofthissystem.
CLOSING UP
REFERENCES INFORMATION
PRODUCTSPECIFICATIONS
PRODUCTREGISTRATION
Company / Installer Name:
Phone Number:
Installer Address:
Date of Installation:
Vehicle Manufacture:
Model:
Year:
Front Antenna Location:
Rear Antenna Location:
Bypass Antenna Location:
Interface/Bypass Module Used:
If YES specify bypass make/model:
All Smart Keys and Bypass Cards Working:
Push-Start Module Installed:
Antenna Mounted on Windshields:
Reviewed Product Operation withEnd-User:
Additional Comments:
YES NO
YES NO
YES NO
YES NO
YES NO