Advantech AIIS-1240 User manual

User Manual
AIIS-1240
Power over Ethernet Control
System

AIIS-1240 User Manual ii
Copyright
The documentation and the software included with this product are copyright © 2014
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements
of the rights of third parties, which may result from its use.
Acknowledgements
Award is a trademark of Award Software International, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel® and Pentium® are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
For more information about this and other Advantech products, please visit our web-
site at:
http://www.advantech.com/
http://www.advantech.com/ePlatform/
For technical support and service, please visit our support website at:
http://support.advantech.com.tw/support/
Part No. 2006S12411 Edition 2
Printed in China January 2014

iii AIIS-1240 User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Declaration of Conformity
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.

AIIS-1240 User Manual iv
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages
Warnings, Cautions and Notes
Warning! Warnings indicate conditions, which if not observed, can cause personal
injury!
Caution! Cautions are included to help you avoid damaging hardware or losing
data. e.g.
There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.
Note! Notes provide optional additional information.

v AIIS-1240 User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
14. Do not leave this equipment in an environment where the storage temperature
may go below -40° C (-40° F) or above 85° C (185° F). This could damage the
equipment. The equipment should be in a controlled environment.
15. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only
with the same or equivalent type recommended by the manufacturer, discard
used batteries according to the manufacturer’s instructions.
16. The sound pressure level at theoperator's position according to IEC 704-1:1982
is no more than 70 dB (A).
17. RESTRICTED ACCESS AREA: The equipment should only be installed in a
Restricted Access Area.
18. DISCLAIMER: This set of instructions is given according to IEC 704-1. Advan-
tech disclaims all responsibility for the accuracy of any statements contained
herein.

AIIS-1240 User Manual vi
Packing List
Before installation, please ensure the following items have been shipped:
1 x AIIS-1240 Unit
4 x Rubber foot
2 x Wall mount bracket
1 x CPU Cooler
1 x English & Simplified Chinese Startup Manual
1 x China RoHS
1 x Utility CD
Ordering information
Optional accessories
Part Number PoE Port Display USB
3.0/2.0 DIO COM 232/ 422/485 COM 232
AIIS-1240-00A1E 4-CH VGA+DVI-D 4 / 4 8-bit 2 4
Part Number Description
98R2124000E DIN-Rail Kit
1757004518-01 220Watt 24Vdc Adapter
AIIS-DIO32-00A1E 32-bit DIO module

vii AIIS-1240 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ...............................................................................................2
1.2 Product Features.......................................................................................2
1.3 Product Specifications...............................................................................2
1.3.1 Processor System.........................................................................2
1.3.2 Memory.........................................................................................3
1.3.3 Graphics........................................................................................3
1.3.4 PoE (Power Over Ethernet)..........................................................3
1.3.5 Ethernet ........................................................................................3
1.3.6 Storage .........................................................................................3
1.3.7 Front I/O........................................................................................3
1.3.8 Rear I/O ........................................................................................3
1.3.9 Watchdog Timer............................................................................3
1.3.10 Power Requirement......................................................................3
1.3.11 Cooling..........................................................................................3
1.3.12 Miscellaneous...............................................................................3
1.3.13 Environment..................................................................................4
1.3.14 Physical Characteristics................................................................4
1.3.15 EMC..............................................................................................4
1.3.16 Safety............................................................................................4
1.4 Jumper Settings ........................................................................................4
1.4.1 How to Set Jumpers......................................................................4
1.4.2 BIOS CMOS (JCMOS1)................................................................4
Table 1.1: Clear BIOS CMOS (JCMOS1)....................................4
1.4.3 Hardware Monitor Alarm (JOBS1) and Watchdog Timer Output
(JWDT1)........................................................................................5
Table 1.2: H/W Monitor Alarm and Watchdog Timer
(JOBS1+JWDT1)........................................................5
Chapter 2 Hardware installation ..........................7
2.1 Front Panel Controls, Indicators & Connectors.........................................8
Figure 2.1 AIIS-1240 Front View .................................................8
2.1.1 Power On/Off Button.....................................................................8
Figure 2.2 Power On/Off Button ..................................................8
Table 2.1: Power Button Connector Pin Assignment ..................8
2.1.2 LED Indicators ..............................................................................8
Figure 2.3 LED Indicators............................................................8
Table 2.2: LED Indicators (Thermal & HDD)...............................9
Table 2.3: LED Indicator (PoE)....................................................9
2.1.3 Power Input Connector.................................................................9
Figure 2.4 Power Input Connector...............................................9
Table 2.4: Power Input Connector Pin Assignment.....................9
2.1.4 Digital I/O......................................................................................9
Figure 2.5 8-bit DIO Connector....................................................9
Table 2.5: 8-bit DIO Connector Pin Assignment..........................9
Figure 2.6 32-bit DIO Connector................................................10
Table 2.6: 32-bit DIO Connector Pin Assignment......................10
2.1.5 VGA+DVI Connector...................................................................10
Figure 2.7 Figure 2.7 VGA Connector.......................................10
Table 2.7: VGA Connector Pin Assignment ..............................11
Figure 2.8 DVI Connector..........................................................11
Table 2.8: DVI Connector Pin Assignment................................11
2.1.6 COM Connectors........................................................................11

AIIS-1240 User Manual viii
Figure 2.9 COM Connectors...................................................... 12
Table 2.9: Front 2-COM Pin Assignment .................................. 12
2.1.7 Ethernet Connectors (LANs)....................................................... 12
Figure 2.10Figure 2.10 Ethernet Connectors............................. 12
Table 2.10:Ethernet Connector Pin Assignment ........................ 12
2.1.8 USB 3.0 Connectors................................................................... 12
Figure 2.11USB 3.0 Connectors................................................. 13
Table 2.11:USB3.0 Connector Pin Assignment ......................... 13
2.1.9 Audio Connector......................................................................... 13
Figure 2.12Audio Connector....................................................... 13
Table 2.12:Audio Pin Assignment.............................................. 13
2.2 Rear Panel Connectors........................................................................... 14
Figure 2.13AIIS-1240 Rear View................................................ 14
2.2.1 COM Connectors........................................................................ 14
Figure 2.14COM Connectors...................................................... 14
Table 2.13:USB3.0 Connector Pin Assignment ......................... 14
2.2.2 USB 2.0 Connectors................................................................... 14
Figure 2.15USB 2.0 Connectors................................................. 15
Table 2.14:USB2.0 Connector Pin Assignment ......................... 15
2.3 CPU Installation ...................................................................................... 15
2.4 CPU Cooler Installation........................................................................... 16
Figure 2.16CPU & CPU Cooler Installation................................ 16
2.5 Memory Installation................................................................................. 17
Figure 2.17Memory Installation.................................................. 17
2.6 HDD Installation...................................................................................... 18
Figure 2.18HDD Installation ....................................................... 18
2.7 Internal USB lock Installation.................................................................. 19
Figure 2.19Internal USB lock Installation ................................... 19
2.8 Cfast Installation ..................................................................................... 19
Figure 2.20Cfast Installation....................................................... 19
2.9 AIIS-DIO32 Installation ........................................................................... 20
Figure 2.21AIIS-DIO32 Installation............................................. 20
2.10 Wallmount Installation............................................................................. 21
Figure 2.22Wallmount Installation .............................................. 21
2.11 DIN-Rail Installation................................................................................ 21
Figure 2.23DIN-Rail Installation.................................................. 21
Chapter 3 AMI BIOS Setup................................. 23
3.1 Introduction............................................................................................. 24
3.2 Entering Setup........................................................................................ 24
3.2.1 Main Setup.................................................................................. 24
Figure 3.1 Main setup screen.................................................... 24
3.2.2 Advanced BIOS Features Setup................................................. 25
Figure 3.2 Advanced BIOS features setup screen.................... 25
Figure 3.3 Advantech BIOS Update V1.3.................................. 26
Figure 3.4 PCI Subsystem Settings........................................... 26
Figure 3.5 PCI Express Settings ............................................... 27
Figure 3.6 ACPI Settings........................................................... 28
Figure 3.7 Trust Computing....................................................... 29
Figure 3.8 S5 RTC configuration............................................... 30
Figure 3.9 CPU Configuration ................................................... 30
Figure 3.10SATA Configuration.................................................. 31
Figure 3.11Intel Trusted Execution Technology Configuration... 32
Figure 3.12USB Configuration.................................................... 33
Figure 3.13Smart Setting............................................................ 34
Figure 3.14Super IO Configuration............................................. 34
Figure 3.15Serial Port 1 Configuration....................................... 35
Figure 3.16Serial Port 2 Configuration....................................... 35

ix AIIS-1240 User Manual
Figure 3.17PC Health Status......................................................36
Figure 3.18PCA-COM232 Super IO Configuration.....................37
Figure 3.19Serial Port 3 Configuration .......................................37
Figure 3.20Serial Port 4 Configuration .......................................38
Figure 3.21Serial Port 5 Configuration .......................................38
Figure 3.22Serial Port 6 Configuration .......................................39
Figure 3.23Serial Port Console Redirection ...............................40
Figure 3.24CPU PPM Configuration...........................................40
3.2.3 Chipset........................................................................................41
Figure 3.25Chipset .....................................................................41
Figure 3.26PCH IO Configuration...............................................42
Figure 3.27PCI Express Configuration .......................................42
Figure 3.28USB Configuration....................................................43
Figure 3.29PCH Azalia Configuration.........................................44
Figure 3.30System Agent (SA) Configuration.............................45
Figure 3.31Graphics Configuration.............................................46
Figure 3.32NB PCIe Configuration.............................................47
Figure 3.33Memory Information..................................................48
3.2.4 Boot.............................................................................................48
Figure 3.34 Boot.........................................................................48
3.2.5 Security.......................................................................................49
Figure 3.35Security.....................................................................49
3.2.6 Save & Exit .................................................................................50
Figure 3.36Save & Exit...............................................................50
Appendix A Programming the Watchdog Timer..51
A.1 Introduction .............................................................................................52
A.1.1 Watchdog Timer Overview..........................................................52
A.1.2 Programming the Watchdog Timer.............................................52
Table A.1: Watchdog Timer Registers.......................................53
A.1.3 Example Program.......................................................................54
Appendix B Programming 8-bit DIO (GPIO).........59
B.1 Supported GPIO Register .......................................................................60
B.2 GPIO Registers.......................................................................................60
B.3 GPIO Example Program-1 ......................................................................60
Appendix C 32-bit DIO Signal Connections.........63
C.1 Overview.................................................................................................64
C.2 Isolated Digital I/O Connections..............................................................64
C.2.1 Dry/Wet Contact Support for Digital Input...................................64
Figure C.1 Isolated Digital Input Connections............................64
C.2.2 Isolated Digital Output Connections............................................64
Figure C.2 Isolated Digital Output Connections.........................65
Appendix D Explored Diagram & Parts List.........67
D.1 Explored Diagram ...................................................................................68
Figure D.1 Explored Diagram.....................................................68
Table D.1: Parts List...................................................................69

AIIS-1240 User Manual x

Chapter 1
1General Introduction
This chapter gives background
information on the
AIIS-1240 series.

AIIS-1240 User Manual 2
1.1 Introduction
AIIS-1240 Box IPC is an ideal, application-ready, system platform solution. All elec-
tronics are protected in a compact sealed case for easy embedding in the customer’s
own housing, or as a stand-alone unit where space is limited.
AIIS-1240’s self-contained PoE controller features performance computing with
Power over Ethernet, rich I/O interface, and extended product longevity, all in a com-
pact form factor. These PoE boxes use the latest, 3rd generation Intel®CoreTM pro-
cessors to deliver improved computing power and graphics performance. Already
fully verified and certified, they offer system integrators a no-nonsense solution.
AIIS-1240 utilizes a single RJ45 cable that carries both data and electrical power.
Compliant with IEEE 802.3af, it can provide a maximum of 15.4 watts of power to
each powered device up to a distance of 100 meters, whereas USB 2.0 can only pro-
vide up to 2.5 watts, with a maximum cable length of 5 meters.
AIIS-1240 offers rich I/O interfaces such as four PoE port channels, max. 40-bit digi-
tal I/O, four USB 3.0, four USB 2.0, and six serial ports. Four USB 3.0 ports provide a
high performance data transfer rate up to 5 Gbps. The two serial ports on the front
panel can be configured as RS-232, RS-422 or RS-485 via BIOS setting. These
interfaces can support a number of various peripheral devices.
1.2 Product Features
Intel® 3rd/2nd Core™ i7/i5/i3 CPU (LGA1155)
4-CH GbE PoE (Power over Ethernet), IEEE 802.3af compliant
–Powered Device auto detection and classification
–Supports IEEE 1588 & GigE Vision devices
Compact & thoughtful design
–Volume less than 3 Liter
–Easier Fan filter maintenance
–Internal USB Type-A with lock design (Max. 49mm length)
–Wall or DIN Rail mounting kit (optional)
–Build in G-sensor for vibration detection
1.3 Product Specifications
1.3.1 Processor System
LGA1155 Intel® Core™ i7/i5/i3/Pentium®/Celeron
CPU Core
i7-3770 Core i7-2600 Core i5-3550S Core i5-2400 Core i3-3220 Core i3-2120 Core G2120 Core G850 Core G540
Core 444 422222
Base
Frequency 3.4 GHz 3.4 GHz 3.0 GHz 3.1 GHz 3.3 GHz 3.3 GHz 3.1 GHz 2.9 GHz 2.5 GHz
L3 Cache 8 MB 8 MB 6 MB 6 MB 3 MB 3 MB 3 MB 3 MB 2 MB
Chipset H61
BIOS AMI 64Mb SPI Flash

3 AIIS-1240 User Manual
Chapter 1 General Introduction
1.3.2 Memory
Supports dual channel DDR3 1066/1333 8 GB per DIMM without ECC function;
Max. capacity is up to 16 GB
1.3.3 Graphics
Chipset: Intel® HD Graphics
1.3.4 PoE (Power Over Ethernet)
Controller: Intel® i210 x 4
Compliant: IEEE 802.3af
Power Output: 15.4W per Channel
1.3.5 Ethernet
Interface: 10/100/1000 Mbps
Controller: LAN1: Intel® 82579V, LAN2: Intel® 82583V
1.3.6 Storage
Internal 2.5” HDD Bay: 1
CFast: 1
1.3.7 Front I/O
Display: VGA+DVI-D
USB: 4 USB3.0
Serial: 2 (RS-232, RS-422 or RS-485 via BIOS setting)
DIO: 8-bit (default), 32-bit (optional by AIIS-DIO32)
1.3.8 Rear I/O
USB: 4 USB2.0
Serial: 4 RS-232
1.3.9 Watchdog Timer
Output: System reset
Interval: Programmable 1~255 sec/min
1.3.10 Power Requirement
Power Type: ATX
Power Input Voltage: 19 VDC ~ 24 VDC
Minimum Power Input: DC19-24V @ 8-6.3A
Normal Power Input: DC19-24V @ 11.57-9.16A
Power Adapter: AC to DC, DC24 V/9.16 A, 220 W (Optional)
1.3.11 Cooling
System Fan: 1 (6cm / 27.7 CFM)
1.3.12 Miscellaneous
LED Indicators: Power, HDD, temperature
Control: Power on/off switch

AIIS-1240 User Manual 4
1.3.13 Environment
Operating Temperature: 0 ~ 45ºC (32 ~ 113ºF)*
Non-operating Temperature: -40 ~ 70ºC (-40 ~ 158ºF)
Operating Humidity: 10 ~ 95% @ 40ºC, non-condensing
Non-operating Humidity: 10 ~ 95% @ 60ºC, non-condensing
* Depends on CPU, i7 CPU supports 0 ~ 40ºC.
1.3.14 Physical Characteristics
Dimension (WxHxD): 232 x 70 x 175 mm
Weight: 2.5Kg
1.3.15 EMC
CE, FCC, CCC, BSMI
1.3.16 Safety
UL, CB, CCC, BSMI
1.4 Jumper Settings
1.4.1 How to Set Jumpers
You can configure your motherboard to match the needs of your application by set-
ting the jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists
of two metal pins and a small metal clip (often protected by a plastic cover) that slides
over the pins to connect them. To “close” (or turn ON) a jumper, you connect the pins
with the clip. To “open” (or turn OFF) a jumper, you remove the clip. Sometimes a
jumper consists of a set of three pins, labeled 1, 2 and 3. In this case you connect
either pins 1 and 2, or 2 and 3. A pair of needle-nose pliers may be useful when set-
ting jumpers.
1.4.2 BIOS CMOS (JCMOS1)
AIIS-1240 CPU card contains a jumper that can erase BIOS CMOS data and reset
the system BIOS information. Normally this jumper should be set with pins 1-2
closed. If you want to reset those data, set JCMOS1 to 2-3 closed for just a few sec-
onds, and then move the jumper back to 1-2 closed. This procedure will reset the
CMOS to its last status or default setting.
Table 1.1: Clear BIOS CMOS (JCMOS1)
Function Jumper Setting
*Keep BIOS CMOS data 1-2 closed
Clear BIOS CMOS data 2-3 closed
*default setting
123
123

5 AIIS-1240 User Manual
Chapter 1 General Introduction
1.4.3 Hardware Monitor Alarm (JOBS1) and Watchdog Timer Output
(JWDT1)
AIIS-1240 contains a watchdog timer that will reset the CPU in the event the CPU
stops processing. This feature means AIIS-1240 will recover from a software failure
or an EMI problem. The JWDT1 jumper settings control the outcome of what the
computer will do in the event the watchdog timer is tripped.
AIIS-1240 also provides jumper: JOBS1 to enable or disable hardware monitor func-
tion.
Table 1.2: H/W Monitor Alarm and Watchdog Timer (JOBS1+JWDT1)
Function Jumper Setting
*Enable watchdog timer
*Enable H/W monitor alarm
*default setting

AIIS-1240 User Manual 6

Chapter 2
2Hardware installation
This chapter introduces external
IO and the installation of
AIIS-1240 Hardware.

AIIS-1240 User Manual 8
2.1 Front Panel Controls, Indicators & Connectors
Figure 2.1 AIIS-1240 Front View
2.1.1 Power On/Off Button
AIIS-1240 has a Power On/Off button with LED indicators on the front side that show
On status (Green LED) and Off/Suspend status (Orange LED). The Power button
supports dual functions: Soft Power -On/Off (Instant off or Delay 4 Seconds then off),
and Suspend.
Figure 2.2 Power On/Off Button
2.1.2 LED Indicators
There are two LEDs on the front panel that indicate system status: The thermal LED
is for system thermal alarm status; and HDD LED is for HDD and Cfast disk status. In
addition, there are four LEDs to indicate the connection of powered device via PoE
port.
Figure 2.3 LED Indicators
Table 2.1: Power Button Connector Pin Assignment
LED color Status
Green Power ON
Amber S1/S4/S5
HDD LED
Temp. LED
PoE
PoE
PoE
PoE

9 AIIS-1240 User Manual
Chapter 2 Hardware installation
2.1.3 Power Input Connector
AIIS-1240 comes with a four pins header that carries 19 ~ 24 VDC external power
input.
Figure 2.4 Power Input Connector
2.1.4 Digital I/O
AIIS-1240 provides one DSUB-15 male connector which offers 4-ch digital input and
4-ch digital output with 2.5KV isolation. AIIS-1240F provides additional DSUB-male
connector which offers 4-ch digital input and 4-ch digital output with 2.5KV isolation.
DSUB-15 Male Connector
Figure 2.5 8-bit DIO Connector
Table 2.2: LED Indicators (Thermal & HDD)
LED color Function
Red Over Temperature LED
Amber SATA LED
Table 2.3: LED Indicator (PoE)
LED color Function
Red Connected Powered Device
Table 2.4: Power Input Connector Pin Assignment
Pin Signal
1GND
2 +19~24 VDC
3 +19~24 VDC
4GND
Table 2.5: 8-bit DIO Connector Pin Assignment
Pin Signal Pin Signal
1GND2DI0
3DI14DI2
5DI36COM
7DO08DO1

AIIS-1240 User Manual 10
DSUB-37 female connector
Figure 2.6 32-bit DIO Connector
2.1.5 VGA+DVI Connector
AIIS-1240 offers an integrated D-sub 24-pin female DVI-D Digital Visual Interface
connector and a D-sub 15-pin VGA; DVI-D carries digital video signal. This supports
high-speed, high-resolution digital displays and traditional analog displays.
Figure 2.7 Figure 2.7 VGA Connector
9DO210DO3
11 GND 12 N/C
13 N/C 14 N/C
15 +5V
Table 2.6: 32-bit DIO Connector Pin Assignment
Pin Signal Pin Signal
1DI0 2 DI2
3DI4 4 DI6
5DI8 6 DI10
7DI12 8 DI14
9GND 10 COM1
11 DO0 12 DO2
13 DO4 14 DO6
15 DO8 16 DO10
17 DO12 18 DO14
19 COM2 20 DI1
21 DI3 22 DI5
23 DI7 24 DI9
25 DI11 26 DI13
27 DI15 28 GND
29 GND 30 DO1
31 DO3 32 DO5
33 DO7 34 DO9
35 DO11 36 DO13
37 DO15
Table 2.5: 8-bit DIO Connector Pin Assignment