Advantech ADAM-5000/TCP Series User manual

Copyright Notice
This document is copyrighted, 2001, by Advantech Co., Ltd.
All rights are reserved. Advantech Co., Ltd., reserves the right
to make improvements to the products described in this
manual at any time without notice.
No part of this manual may be reproduced, copied, translated
or transmitted in any form or by any means without the prior
written permission ofAdvantech Co., Ltd. Information
provided in this manual is intended to be accurate and reliable.
However,Advantech Co., Ltd. assumes no responsibility for
its use, nor for any infringements upon the rights of third
parties which may result from its use.
Acknowledgments
IBM and PC are trademarks of International Business
Machines Corporation.
Edition 4.0
Aug. 2007

Product Warranty
Advantech warrants to you, the original purchaser, that each of its
products will be free fromdefects in materials and workmanship for two
year from the date of purchase. This warranty does not apply to any
product which have been repaired or altered by other than repair
personnel authorized by Advantech, or which have been subject to
misuse, abuse, accident or improper installation. Advantech assumes no
liability as a consequence of such events under the terms of this
Warranty.
Because of Advantech’s high quality-control standards and rigorous
testing, most of our customers never need to use our repair service. If an
Advantech product ever does prove defective, it will be repaired or re-
placed at no charge during the warranty period. For out-of-warranty
repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem
encountered (e.g. type of PC, CPU speed, Advantech
products used, other hardware and software used etc.).
Note anything abnormal and list any on-screen
messages you get when the problem occurs.
2. Call your dealer and describe the problem. Please have
your manual, product, and any helpful information
readily available.
3. If your product is diagnosed as defective, you have to
request an RAM number. When requesting an RMA
(Return Material Authorization) number, please access
ADVANTECH’s RMA web site: http://
www.advantech.com.tw/rma. If the web sever is shut
down, please contact our office directly. You should fill
in the “Problem Repair Form”, describing in detail the
application environment, configuration, and problems
encountered. Note that error descriptions such as
“does not work” and “failure” are so general that we
are then required to apply our internal standard repair
process.
4. Carefully pack the defective product, a completely
filled-out Repair and Replacement Order Card and a

photocopy of dated proof of purchase (such as your
sales receipt) in a shippable container. A product
returned without dated proof of purchase is not eligible
for warranty service.
5. Write the RMA number visibly on the outside of the
package and ship it prepaid to your dealer.

Technical Support We want you to get the maximum performance
from your products.So if you run into technical difficulties, we are
here to help. For most frequently asked questions you can easily find
answers in your product documentation. Moreover, there area huge
databaseabout troubleshooting and knowledge Base as technical
reference on our website. These answers are normally a lot more
detailed than the ones we can give over the phone. So please consult this
manual or the web site first. If you still cannot find the answer, gather all
the information or questions that apply to your problem and,with the
product close at hand, call your dealer. Our dealers are well trained and
ready to give you the support you need to get the most from your
Advantech products. In fact, most problems reported are minor and are
able to be easily solved over the phone.
In addition, free technical support is available from Advantech engi-
neers every business day. We are always ready to give advice on appli-
cation requirements or specific information on the installation and opera-
tion of any of our products.
Website information:
You can access the most current support on our website:
http://www.advantech.com/support/ If you find a problem with our
documentation, please let us know by completing and returning the
“Support Request Form” on our website:
http://www.advantech.com/support/request_dir.htm

Organization of this manual This Manual has six chapters, three
appendices. The following table lists each chapter or appendices with its
corresponding title and a brief overview of the topics covered in it.
Cha p t e r /
Appe ndi x
T i tle T op ic s C o ve r e d
I
n tr o duces t h e s u it a b l e a ppl y i ng i ndus tri e s
a nd t h e p o s iti on i n a SCAD A s ys t e m .
S u mm a r ize th e featu r es an d th e sp ecific a tio n
of AD AM - 5000/ TCP . Ex pl ai ns t h e f unc ti ons of
th
e L E D in dic a tors .
1 U nders t a ndi ng Y our Sys t e m
P r o v id es a b r iefly se lectio n ch art an d
s p ec ifi c a ti on t a bl e of ADAM - 5000 I / O
m odu le s fo r u ser s t o or g a n i ze th eir sys tem
ea sily . G i ve a dir ection to ca lcu l ate s ystem
c a pa c it y and se l e c t a c e rt a i n powe r s uppl y .
R e c o mm e nd a s t a ndar d f o r co mm uni ca ti on
c a bl e a nd c onne ctor .
2 S e l ec ti ng Y our H a rdwa r e
L i sts t h e n ece ssar y co m pone nt s a nd pr ope r
en v ir on m e n t i n inst alli ng p r o cess . Desc ri b e s
t h e H a r d w a r e dim e ns i on a nd t h e wa y t o pl a c e
or m ount i t . Ex pl a i ns t h e rul e of m a ppi ng I/ O
ad d r ess. D escr ib es the w iri ng an d c onnec ti ng
de t a il f o r AD A M-5000/ TC P .
3 H a r d w are In st all a tio n Gu id e
I
n tr o duces t h e d e t a il sp e c ifi c a ti ons f unc ti ons
an d ap p lica t io n w iri ng o f each A D A M - 5000
4 I/ O M odul e I n tr oduc ti on I/
O m odul e s .
Gu id es u ser s to u se W i ndo w s Utility f o r
n e tw o r k & se cu rity settin g , I/O ran g e
con f ig u r a t io n, a ccu r a cy c a libr a tio n , co mm an d
s e tti ng , and so on.
5 S ys t e m Conf i gur a ti on G u i d e
I
n tr o duces t h e f unc ti ons a nd s tr u c t ur e of D LL
dr i vers and c o mm a nd s e t s . Ex pl a i n how t o
i n t e gr at e t h e s e pr ogra mm i ng tool s t o pl a n your
a
ppl i c a ti on pr ogr am .
6
Pl a nni ng Y o ur Appl i c a ti on
Prog ra m
Prov i d e s or gani z e d wor k she e t s f o r us ers t o
e s t a bl i s h s ys t e m c onf i gur a ti on doc um e n t i n
or der .
A D e s ig n W o r ksh ee ts
B D a t a Fo r m a t s an d I/O Ra ng e
Prov i d e s de t a il i n f o rm at i on about D a t a
f o r m a t s a nd I / O R a nge of Ana l og Modul e .
C G roundi ng R e f e re nc e
Ex pl a i ns t h e c onc e p ts a bout f i e l d groundi ng
a nd sh i e l d i ng.

How to use this manual
The following flow chart demonstrates a thought process that you can
use when you plan your ADAM-5000/TCP system.
System Design Flow Chart
System Hardware Configuration
Select I/O Module
Install Utility Software
Select Power Supply
Selecting Your
I/O Module Configuration
Hardware Component
Select Link Terminal & Cable
Network Setting
System Configuration
Select Operator Interface
I/O Module Calibration
Guide
Security Setting
Determine Proper Environment
Terminal Emulation
Install Main Unit and Module
UDP Data Stream
Hardware Installation
System Mounting
Guide
Modbus Data Gateway
Wiring and Connecting
Using ADAM-5000/TCP
DLL Driver
Planning Your
I/O Address Mapping
Application Program
Using ADAM-5000/TCP
Command Set
I/O Modules
Individual I/O Module
Introduction
Introduction
Relational Document &
Technical Information
Appendix

Contents
Chapter 1 Understanding Your System .................... 1-1
1-1 Introduction ................................................................. 1-2
1-2 Major Features ............................................................ 1-3
1-2-1 Communication Network ...............................................1-3
1-2-2 Modbus/TCP Protocol ....................................................1-3
1-2-3 Hardware Capacity & Diagnostic.................................1-3
1-2-4 Communicating Isolation...............................................1-4
1-2-5 Completed set of I/O modules for total solutions ...........1-4
1-2-6 Built-in real-time OS and watchdog timer .......................1-4
1-2-7 Software Support ...........................................................1-4
1-2-8 Security Setting .............................................................1-5
1-2-9 UDP Data Stream .......................................................1-5
1-2-10 Modbus Ethernet Data Gateway ....................................1-5
1-3 Technical specification of ADAM-5000/TCP System .. 1-6
1-3-1 System ..........................................................................1-6
1-3-2 Ethernet Communication................................................1-6
1-3-3 Serial Communication .....................................................1-6
1-3-4 Power .............................................................................1-7
1-3-5 Isolation .........................................................................1-7
1-3-6 Mechanical.....................................................................1-7
1-3-7 Environment ................................................................... 1-7
1-3-8 Dimensions .................................................................... 1-7
1-3-9 Basic Function Block Diagram......................................1-8
1-4 LED Status of ADAM-5000/TCP main unit ............. 1-8
Chapter 2 Selecting Your Hardware Components….2-1
2-1 Selecting I/O Module ................................................ 2-2
2-2 Selecting Power Supply ............................................ 2-6
2-3 Selecting Link Terminal and Cable .......................... 2-8
2-4 Selecting Operator Interface ................................... 2-10
Chapter 3 Hardware Installation Guide .................. 3-1
3-1 Determining the proper environment ...................... 3-2
3-1-1 Check the content of shipping box .................................3-2
3-1-2 System Requirement ....................................................3-2
3-1-3 I/O modules ................................................................... 3-2
3-2 Installing your main unit and module .................... 3-3

3-3 Mounting ......................................................................3-4
3-3-1 Panel mounting ...........................................................3-4
3-3-2 DIN rail mounting ........................................................3-4
3-4 Wiring and Connections ...........................................3-6
3-4-1 Power supply wiring ...................................................... 3-6
3-4-2 I/O modules wiring .....................................................3-7
3-4-3 System Network Connections ......................................3-8
3-5 Assigning address for I/O Modules ........................ 3-10
Chapter 4 I/O Module Introduction ........................ 4-1
Chapter 5 System Hardware Configuration ............ 5-1
5-1 System Hardware Configuration............................. 5-2
5-2 Install Utility Software on Host PC ........................ 5-3
5-3 ADAM-5000/TCP Windows Utility Overview......... 5-3
5-3-1 Main Menu .................................................................. 5-3
5-3-2 Ethernet Network Setting .............................................5-5
5-3-3 Add Remote Station ....................................................... 5-8
5-3-4 I/O Module Canfiguration ...........................................5-9
5-3-5 Alarm Setting ............................................................... 5-14
5-3-6 I/O Module Calibration ................................................. 5-15
5-3-7 Firmware Update .......................................................... 5-17
5-3-8 Security Setting ...........................................................5-18
5-3-9 Terminal Emulation ....................................................... 5-19
5-3-10 Data Stream ................................................................ 5-20
5-3-11 Data Gateway Setting ................................................. 5-22
Chapter 6 Planning Your Application Program…... 6-1
6-1 Introduction .................................................................6-2
6-2 DLL (Dynamic Link Library) Driver ..........................6-2
6-2-1 Index ............................................................................. 6-2
6-2-2 Programming Flow ...................................................... 6-4
6-2-3 Function Descriptions .....................................................6-10
6-2-4 Return Codes .................................................................. 6-30
6-3 ADAM-5000/TCP Command ..................................... 6-32
6-3-1 Command Structure ....................................................... 6-32
6-3-2 Modbus Function Code Introduction .............................. 6-33
6-4 Apply with ASCII Command for ADAM-5000/TCP
System ........................................................................... 6-39
6-4-1 Sytax of ASCII............................................................ 6-39
6-4-2 System Command Set............................................... 6-40
6-4-3 Analog Input Command Set .......................................... 6-48
6-4-4 Analog Output Command Set ...................................... 6-127
6-4-5 Digital Input/Output Command Set .............................. 6-141

Appendix A Design Worksheets ............................A-1
Appendix B Data Formats and I/O Ranges............B-1
B.1 Analog Input Formats ...............................................B-2
B.2 Analog Input Ranges - ADAM-5017 ..............................B-4
B.3 Analog Input Ranges - ADAM-5018/5018P....................B-5
B.4 Analog Input Ranges - ADAM-5017H/5017UH...............B-7
B.5 Analog Output Formats ..............................................B-8
B.6 Analog Output Ranges..................................................B-8
B.7 ADAM-5013 RTD Input Format and Ranges...............B-9
Appendix C Grounding Reference........................C-1
C.1 Grounding ...................................................................C-3
C.2 Shielding ..................................................................... C-11
C.3 Noise Reduction Techniques......................................C-17
C.4 Check Point List ........................................................C-18

Figures
Figure 1-1: Apply to System Application ................................................. 1-2
Figure 1-2: ADAM-5000/TCP system & I/O module dimensions ………. 1-7
Figure 1-3: Function block diagram ......................................................... 1-8
Figure 1-4: ADAM-5000/TCP LED Indicators ........................................... 1-8
Figure 2-1: ADAM-5000 I/O Module Selection Chart ............................... 2-3
Figure 2-2: Ethernet Terminal and Cable Connection ............................ 2-8
Figure 2-3 RS-485 Terminal and Cable Connection ............................... 2-9
Figure 3-1: Module alignment and installation ........................................ 3-3
Figure 3-2: Secure the module to the system ......................................... 3-3
Figure 3-3: ADAM-5000/TCP panel mounting screw placement ........... 3-4
Figure 3-4: ADAM-5000/TCP DIN rail mounting ...................................... 3-5
Figure 3-5: Secure ADAM-5000/TCP System to a DIN rail ..................... 3-5
Figure 3-6: ADAM-5000/TCP power wiring .............................................. 3-6
Figure 3-7: ADAM-5000 I/O Module Terminal Block wiring .................... 3-7
Figure 3-8: System network connection .................................................. 3-8
Figure 3-9 Serial Network Connection ..................................................... 3-9
Figure 3-10: I/O Modules Address Mapping .......................................... 3-10
Figure 5-1: Hardware Configuration ........................................................ 5-2
Figure 5-2: operation Screen .................................................................... 5-3
Figure 5-4: Network Setting ...................................................................... 5-5
Figure 5-3: Tool Bar ................................................................................... 5-5
Figure 5-5: Communication testing function .......................................... 5-6
Figure 5-6: Define Device Name and Description ................................... 5-6
Figure 5-7: TCP/IP Network setting .......................................................... 5-7
Figure 5-8: Adding ADAM-5000/TCP screen ........................................... 5-8
Figure 5-9: Digital I/O Module Configuration ........................................... 5-9
Figure 5-11: Current Analog Input Status .............................................. 5-10
Figure 5-10: Operating and Indicating Icons ......................................... 5-10
Figure 5-12: setting range and integration time ................................... 5-11
Figure 5-13: Analog Module Configuration Screen .............................. 5-12
Figure 5-14: Counter/Frequency Module Configuration ...................... 5-12
Figure 5-15: Location of Counter/Frequency Module ........................... 5-13
Figure 5-16: Alarm Setting for Analog Input and Counter Modules .... 5-14
Figure 5-17: Zero Calibration .................................................................. 5-15
Figure 5-18: Span Calibration ................................................................. 5-15

Figure 5-19: CJC Calibration .................................................................. 5-16
Figure 5-20: Analog Output Module Calibration ................................... 5-16
Figure 5-21: Firmware Upgrade .............................................................. 5-17
Figure 5-22: Password Setting ............................................................... 5-18
Figure 5-23: Command Emulation ......................................................... 5-19
Figure 5-24: Data Stream Configuration ................................................ 5-20
Figure 5-25: Data Stream Monitoring ..................................................... 5-21
Figure 5-26: RS-485 Modbus Network Setting ...................................... 5-22
Figure 6-1: Request Comment Structure ............................................... 6-32
Figure 6-2: Response Comment Structure ............................................ 6-33
Figure 6-3: ASCII Command Structure in ADAM-5000/TCP ................. 6-39
Figure 6-4: Data format for 8-bit parameters ......................................... 6-64
Figure 6-5: The other bits are not used and are set to 0. ....................6-128
Figure C-1: Think the EARTH as GROUND. ............................................ C-3
Figure C-2: Grounding Bar ....................................................................... C-4
Figure C-3: Normal mode and Common modC ...................................... C-5
Figure C-4: Normal mode and Common modC ...................................... C-6
Figure C-5: The purpose of high voltage transmission ......................... C-7
Figure C-6: wire impedancC ..................................................................... C-8
Figure C-7: Single point grounding (1) .................................................... C-9
Figure C-8: Single point grounding (2) .................................................. C-10
Figure C-9: Single isolated cable ........................................................... C-11
Figure C-10: Double isolated cable ....................................................... C-12
Figure C-11: System Shielding .............................................................. C-13
Figure C-12: The characteristic of the cable ........................................ C-14
Figure C-13: System Shielding (1) ......................................................... C-15
Figure C-14:System Shielding (2) .......................................................... C-16
Figure C-15: Noise Reduction Techniques ........................................... C-17

Tables
Table 2-1: I/O Selection Guidelines .......................................................... 2-2
Table 2-2: I/O Modules Selection Guide .................................................. 2-5
Table 2-3: Power Consumption of ADAM-5000 series ........................... 2-6
Table2-4: Power Supply Specification Table .......................................... 2-7
Table 2-5: Ethernet RJ-45 port Pin Assignment ..................................... 2-8
Table 4-1: I/O module support List……….. ............................................. 4-1
Table 6-1: Response Comment Structure ............................................. 6-33
Table 6-2: CPU Command Set Table ...................................................... 6-40
Table 6-3 Baud rate codes ...................................................................... 6-42
Table 6-4: ADAM-5013 RTD Input command Set Table ........................ 6-49
Table 6-5: ADAM-5017/5018 Analog Input command Set Table .......... 6-63
Table 6-6: ADAM-5017H Analog Input command Set Table ................ 6-80
Table 6-7 Analog Input alarm command set table ................................ 6-89
Table 6-8 Analog Input alarm command set table ...............................6-108
Table 6-9: Analog Output command Set Table ....................................6-127
Table 6-10: Counter/Frequency Command Set Table .........................6-149
Table A-1: I/O Data Base ........................................................................... A-3
Table A-2: Summary Required Modules ................................................. A-5
Table A-3: Table for Programming .......................................................... A-6

Chapter 1
Understanding Y our System
UsingthisChapter
If you want to read about Go to page
Introduction 1-2
Major Feature 1-3
Technical Specification 1-6
LED Status of ADAM-5000/TCP Series main unit 1-8

Chapter 1 Understanding Your System
1-1 Introduction Undoubtedly, Ethernet connectivity is becoming to a
big trend for industrial applications. Longer communication distances,
faster communication speeds, and greater advantages attract people into
developing their system based upon this network scenario. But there
used to be a thresh-old in connecting information layers and field control
layers.People usually had to prepare a data exchange server between
information systems and control systems as a communication bridge.
Obviously, it takes a lot of time and money. To meet user’s requirements,
Advantech announces the new DA&C system, the ADAM-5000/TCP
Series, the Ethernet I/O solution for people developing their eAutomation
architecture. It can be applied to various applications, such as traffic,
building, telecom, water treatment, and others.
ADAM-5000/TCP Series include the following 2 products:
ADAM-5000/TCP: 8-slot Distributed DA&C System for Ethernet
ADAM-5000L/TCP: 4-slot Distributed DA&C System for Ethernet
1-2 ADAM-5000/TCP User’s Manual

Understanding Your System Chapter 1
1-2 Major Features
1-2-1 Communication Network
By adopting a 32-bit RISC CPU, the ADAM-5000/TCP Series has
greatly ad- vanced data processing abilities for the user, especially for
network com- munications (response time < 5ms). There is a standard
RJ-45 modular jack Ethernet port on the ADAM-5000/TCP’S CPU
board, and I/O mod- ules field signals would be able to link with the
Ethernet directly without assistance from other hardware devices such as
converters or data gate- ways. The communication speeds can be auto-
switched between 10 M and 100 Mbps data transfer rate depending
upon the network environ- ment. Through an Ethernet network, your
DA&C systems, computer workstations, and higher-level enterprise
MIS servers can access plant- floor data. Such data can be used in
system supervising, product sched- uling, statistical quality control, and
more.
1-2-2 Modbus/TCP Protocol Modbus/TCP is one of the most
popular standards for industrial Ethernet networks. Following this
communicationprotocol, the ADAM-5000/TCP Series is easy to integrate
with any HMI software packages or user-developed applications that
support Modbus. Users do not have to prepare a specific driver for the
ADAM-5000/TCP Series when they install the DA&C sys- temwith
their own operating application. It will certainly reduce engineer effort.
Moreover, the ADAM-5000/TCP Seriesworks as a Modbus data server.
It allows eight PCs or tasks to access its current data simultaneously
from anywhere: LAN, Intranet, or Internet.
1-2-3 Hardware Capacity & Diagnostic Advantech’s
ADAM-5000/TCP Seriesis designed with a high I/O capacity and
supports all types of ADAM-5000 I/O modules. Providing eight slots for
any mixed modules, this DA&C system handles up to 128 I/O points
(fourADAM-5024sallowed).Differentfrom other mainunits,theADAM-
5000/TCP Series not only has a higher I/O capacity, but it also has a
smarter diagnostic ability. There are eight indicators on the front case of
the CPU module. Users can read the system status clearly, including
power, CPU, Ethernet link, Communication active, communication rate,
and more. In addition, there are also Tx and Rx LEDs on the Ethernet
port, indicating data transfer and reception.
ADAM-5000/TCP User’s Manual
1-3

Chapter 1 Understanding Your System
1-2-4 Communicating Isolation
High-speed transient suppressors isolate ADAM-5000/TCP SeriesEthernet
port from dangerous voltage up to 1500V
DC power spikes and avoid
surge damage to whole system.
1-2-5 Completed set of I/O modules for
total solutions
The ADAM-5000/TCP Series uses a convenient backplane system
common to the ADAM-5000 series. Advantech’s complete line of
ADAM-5000 mod- ules integrates with the ADAM-5000/TCP Series to
support your applications
(notincludeADAM-5090). Full ranges of digital module supports 10 to
30 V
DC
input and outputs. A set of analog modules provide 16-bit
resolution and programmable input and output (including bipolar) signal
ranges. For details, refer to Chapter
4 I/O Modules.
1-2-6 Built-in real-time OS and watchdog timer The
microprocessor also includes a real-time OS and watchdog timer. The
real-timeOSisavailable tohandleseveraltasksatthesame time.The
watchdog timer is designed to automatically reset the microprocessor if
the system fails. This feature greatly reduces the level of maintenance
required and makes the ADAM-5000/TCP Series ideal for use in
applications which require a high level of system performance and
stability.
1-2-7 Software Support
Based on the Modbus standard, the ADAM-5000/TCP
Seriesfirmware is a built-in Modbus/TCP server. Therefore,
Advantech provides the neces- sary DLL drivers, OCX component OPC
Server, and Windows Utility for users for client data for the ADAM-
5000/TCPSeries. Users can configure this DA&C system via Windows
Utility; integrate with HMI software pack- age via Modbus/TCP driver
or Modbus/TCP OPC Server. Even more, you can use the DLL driver
or OCX component to develop your own applications.
1-4 ADAM-5000/TCP User’s Manual

Understanding Your System Chapter 1
1-2-8 Security Setting
Though Ethernet technology comes with great benefits in
speed and integration, there also exist risks about network invasion
from outside. For this reason, a security protection design was built into
the ADAM-5000/TCPSeries. Once the user has set the password into
the ADAM-5000/ TCP firmware, important system configurations
(Network,Firmware,Pass- word) can only be changed through password
verification.
1-2-9 UDP Data Stream Most of time, each hostPC in a DA&C
systemneeds toregularly request the I/O devices via TCP/IP packs to
update current data. It may cause to data collision and lower
performance on the network, especially when there are frequent
communication between multi-servers and I/O devices. To reduce the
communication loading of the host computer on your Ethernet
network, the ADAM-5000/TCP Seriesalso supports UDP
(User Datagram Protocol) protocol to broadcast the data packs to
specific IPs without requesting commands. Users can apply this
great feature to implement Data Stream, Event Trigger, and other
advanced functions.
1-2-10 Modbus Ethernet Data Gateway
Much more than an I/O system, ADAM-5000/TCP Series provides an
RS-485 network interface for other Modbus devices integration.
It works as Ethernet Data Gateway, upgrading Modbus serial network
devices up to Ethernet layer. Maximum 16 nodes of ADAM-5511 or 3’rd
party products supported Modbus protocol are allowed to integrate
with an ADAM-5000/TCPSeries. This great feature enlarges your system
scope, as opposed to other general dummy I/O system.
ADAM-5000/TCP User’s Manual
1-5

Chapter 1 Understanding Your System
1-3 Technical specification of ADAM-
5000/TCP Series System
1-3-1 System
• CPU:ARM32-bitRISCCPU
• Memory:4MBFlashRAM
• OperatingSystem:Real-timeO/S
• Timer BIOS: Yes
• I/OCapacity:8slots(ADAM-5000/TCP)
4 slots (ADAM-5000L/TCP)
• StatusIndicator: Power(3.3V,5V), CPU, Communication (Link,
Collide,10/100Mbps, Tx,Rx)
• CPUPowerConsumption:5.0W
• ResetPushBottom: Yes
1-3-2 Ethernet Communication
• Ethernet:10BASE-TIEEE802.3
100BASE-TXIEEE802.3u
• Wiring: UTP, category 5 or greater
• BusConnection: RJ45modular jack
• Comm.Protocol:Modbus/TCP
• DataTransfer Rate: Up to 100 Mbps
• MaxCommunicationDistance:100meters
• EvenResponseTime:<5ms
• DataStreamRate: 50 ms to 7 days
1-3-3 Serial Communication
• RS-485 signals: DATA +, DATA-
• Mode:Halfduplex,multi-drop
• Connector:Screwterminal
• Transmission Speed: Up to 115.2 Kbps
• Max.TransmissionDistance:4000 feet(1220 m)
1-6 ADAM-5000/TCP User’s Manual

Understanding Your System Chapter 1
1-3-4 Power
• Unregulated10 to 30V
DC
• Protection: Over-voltage and power reversal
1-3-5 Isolation
• EthernetCommunication:1500V
DC
• I/OModule:3000V
DC
1-3-6 Mechanical
• Case: KJW with captive mounting hardware
• Plug-inScrewTerminal Block:
Accepts 0.5 mm 2 to 2.5 mm 2 , 1 - #12 or 2 - #14 to #22 AWG
1-3-7 Environment
• OperatingTemperature: - 10 to 70º C (14 to158ºF)
• StorageTemperature: - 25 to 85º C(-13 to 185º F)
• Humidity: 5to 95%,non-condensing
• Atmosphere: No corrosive gases
NOTE: Equipment will operate below 30% humidity.
However, static electricity problems occur much more
frequently at lower hu- midity levels. Make sure you take
adequate precautions when you touch the equipment. Consider
using ground straps, anti- static floor coverings, etc. if you use
the equipment in low humidity environments.
1-3-8 Dimensions The following diagrams show the dimensions
of the system unit and an I/O unit. All dimensions are in millimeters.
Figure 1-2: ADAM-5000/TCP system & I/O module dimensions
ADAM-5000/TCP User’s Manual
1-7
355.0
331.5
309.5