Advantech ADAM-3013 User manual

Introduction
ADAM-3013 is a DIN-rail mounted, RTD input signal conditioning module
with 1000VDC 3-way isolation between input, output and power. The
switch configurable input and output offers flexible ,wide raging capability
for Platinum and Nickel RTDS. The input of the ADAM-3013 RTD input
can be configured for any one of up to fourteen defined temperature ranges
(see “Input Range” under “Specification” below) and two OEM-defined
ranges. The output is linearized to the RTD temperature input and can be set
for either 0~5V, 0~10V or 0~2 m A.
The ADAM-3013 is equipped with a dual function LED signal monitor. The
front mounted LED indicates both line power and conversion status.
Conversion operation is indicated by a flashed LED.If the LED is off, please
check that the power connection and wiring connections are correct.
3-way isolation completely eliminates ground loops from any
source.Isolation protects expensive SCADA systems from ground faults and

significantly reduces the effect of high common mode voltage which are
prevalent in many RTD applications.
The ADAM-3013 can be mounted on a DIN-rail and features daisy chain
power wiring to connect easily from adjacent ADAM-3000 series modules
in a compact space.Also,the ADAM-3013 modules uses single +24 VDC
with very low power consumption and can be operate in environments with
high humidity and wide temperature variation.
Features
• Switch configurable input ranges for Platinum and Nickel RTDs.
• Switch configurable linearized output ranges (V and m A).
• 1000 VDC 3-way isolation
• Flexible DIN-rail mounting
• Power/Signal status LED indicator
• Operates from a single of 24 VDC
• Operating temperature range: 0~70°C.
Specifications
• Input range
PT100(a=.00385) –100~100°C. PT100(a=.00392) –100~100°C.
PT100(a=.00385) 0~100°C PT100(a=.00392) 0~100°C
PT100(a=.00385) 0~200°C PT100(a=.00392) 0~200°C
PT100(a=.00385) 0~600°C PT100(a=.00392) 0~600°C
PT100(a=.00385) –100~0°C NI120 0~100°C
PT100(a=.00385) –100~200°C NI120 –80~100°C
PT100(a=.00385) –50~50°C PT100(a=.00385) OEM defiened
PT100(a=.00385) –50~150°C PT100(a=.00392) OEM defiened.
Input Connections
• Input Connections: 2,3 or 4 wires

• Input range: 0~5V, 0~10V,0~20m A
• Accurancy: +/- 0.1% of full range (voltage) or
• +/- 0.15°C (voltage)
+/- 0.2% of full range (current)
• Temperature drift: +/- 30 ppm of full range
• Input CMR at DC: 92dB minimum
• Isolation: 1000 VDC.
• Supply voltage: 24 Vdc +/- 10%
• Operating temperature range: 0~70°C
• Bandwidth: 4Hz
• Power consumption: <0.95W
Ordering Information
• ADAM-3013 : Isolated RTD Input Module
Configuration
Please refer to the following pages on the Adam-3013 configuration.
Figure 1 shows the RTD Wiring of ADAM-3013. Figure 2 shows the
terminal wiring of ADAM-3013.Positive terminals 9 and 7 are internally
connected, as are negative terminals 12 and 10.Power can be connected
through the adjacent modules, making wiring much easier.ADAM-3013
uses single 24 VDC. Table 1 shows the switch setting to configure the
RTD input type and range.To reach the switches,you need to remove the
DIN-rail bracket by sliding it down.