Advantech IDK-1110WR-series User manual

User Manual
IDK-1110WR-series
TFT-LCD 10.1” WSVGA (LED
Backlight)

IDK-1110W User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2014
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice. No part of this manual may be reproduced, copied, translated or transmitted
in any form or by any means without the prior written permission of Advantech Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. How-
ever, Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringe-
ments of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of American Megatrends Inc.
IBM and PC are trademarks of International Business Machines Corporation.
Intel® Core 2 Quad, Pentium Dual Core and Celeron are trademarks of Intel Corpo-
ration.
WinBond is a trademark of Winbond Corporation.
All other product names or trademarks are properties of their respective owners.
Part No. 2006111021 Edition 2
Printed in Taiwan Nov 2014

iii IDK-1110W User Manual
A Message to the Customer
Advantech Customer Services
Each and every Advantech product is built to the most exacting specifications to
ensure reliable performance in the harsh and demanding conditions typical of indus-
trial environments. Whether your new Advantech equipment is destined for the labo-
ratory or the factory floor, you can be assured that your product will provide the
reliability and ease of operation for which the name Advantech has come to be
known. Your satisfaction is our primary concern. Here is a guide to Advantech’s cus-
tomer services. To ensure you get the full benefit of our services, please follow the
instructions below carefully.
Technical Support
We want you to get the maximum performance from your products. So if you run into
technical difficulties, we are here to help. For the most frequently asked questions,
you can easily find answers in your product documentation. These answers are nor-
mally a lot more detailed than the ones we can give over the phone.
So please consult this manual first. If you still cannot find the answer, gather all the
information or questions that apply to your problem, and with the product close at
hand, call your dealer. Our dealers are well trained and ready to give you the support
you need to get the most from your Advantech products. In fact, most problems
reported are minor and are able to be easily solved over the phone.
In addition, free technical support is available from Advantech engineers every busi-
ness day. We are always ready to give advice on application requirements or specific
information on the installation and operation of any of our products.

IDK-1110W User Manual iv
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

v IDK-1110W User Manual
Contents
Chapter 1 Overview...............................................1
1.1 General Description .................................................................................. 2
1.2 Display Characteristics.............................................................................. 2
1.3 Optical Characteristics .............................................................................. 2
1.3.1 Measuring Condition ..................................................................... 3
1.3.2 Measuring Equipment ................................................................... 3
1.4 Block Diagram........................................................................................... 5
Figure 1.1 TFT LCD module ........................................................ 5
1.5 Absolute Maximum Ratings ...................................................................... 5
1.5.1 Absolute Max Rating..................................................................... 5
1.6 Dimensions ............................................................................................... 6
1.6.1 Front view ..................................................................................... 6
1.6.2 Rear view ...................................................................................... 7
Chapter 2 Electrical Characteristics...................9
2.1 TFT LCD Module..................................................................................... 10
2.1.1 Signal Electrical Characteristics.................................................. 10
2.2 Backlight Unit .......................................................................................... 11
2.2.1 Parameter guideline for LED backlight ....................................... 11
Chapter 3 Signal Characteristics.......................13
3.1 Electrical Interface Connection ............................................................... 14
3.2 Interface Timing ...................................................................................... 15
3.2.1 Timing Characteristics ................................................................ 15
Table 3.1: Timing Characteristics .............................................. 15
3.2.2 Input Timing Diagram.................................................................. 15
3.3 Power ON/OFF Sequence ...................................................................... 16
Chapter 4 Display Connector Definition ...........19
4.1 TFT LCD Signal(CN1): LVDS Connector................................................ 20
Table 4.1: Connector ................................................................. 20
4.2 LED Backlight Unit (CN1): LED Backlight Connector ............................. 20
4.3 LED Backlight Unit(CN2): LED Driver board........................................... 21
4.4 LED Driver board drawing....................................................................... 21
Chapter 5 Touch Screen.....................................23
5.1 Touch Characteristics ............................................................................. 24
Chapter 6 Touch Controller................................25
6.1 Touch Controller Characteristics............................................................. 26
6.2 Specifications .......................................................................................... 26
6.3 Environmental Feature............................................................................ 26
6.4 Pin Assignment and Description ............................................................. 27
6.4.1 Connector and LED Location...................................................... 27
6.4.2 Combo Interface Connector, JP1, Pins and Signal Descriptions 27

IDK-1110W User Manual vi
Figure 6.1 Board mounted header............................................. 28
6.4.3 Touch Screen Connector, JP2, Pins and Signal Descriptions.... 28
Appendix A Handling Precautions ....................... 29
A.1 Handling Precautions.............................................................................. 30

Chapter 1
1Overview

IDK-1110W User Manual 2
1.1 General Description
This specification applies to the 10.1 inch color TFT LCD module IDK-1110WR-
55WSA1E. IDK-1110WR-55WSA1E is designed with a wide viewing angle; wide
operating temperature and long life LEDs backlight, making it well suited as display
units for Industrial Applications. A LED driving board for backlight unit is included in
this panel and the structure of the LED units is replaceable. IDK-1110WR-55WSA1E
uses a built in timing controller and LVDS interface. The screen format is intended to
support the WSVGA (1024(H) x 600(V)) screen and 262k colors (RGB 6-bits). IDK-
1110WR-55WSA1E are a RoSH product.
1.2 Display Characteristics
The following characteristics are summarized on the table below for under 25°C con-
ditions.
1.3 Optical Characteristics
The optical characteristics are measured under stable conditions at 25°C (Room
Temperature):
Items Specifications Unit
Screen Diagonal 10.1 (Diagonal) inch
Active Area 222.72(H) x 125.28(V) mm
Pixels H x V 1024 x 3(RGB) x 600
Pixel Pitch 0.2715 x 0.2088 mm
Pixel Arrangement R.G.B. Vertical Stripe
Display Mode TN, Normally White
Nominal Input Voltage VDD 3.3 typ. Volt
Typical Power Consumption 6.184 typ. Watt
Weight 420 ± 10 Grams
Physical Size 235.0(W) x 145.8(H) x 10.25(D) (typ.) mm
Electrical Interface 1 channel LVDS
Surface Treatment Anti-glare, Hardness 3H
Support Color 262K(6-bit)
Temperature Range
Operating
Storage (Non-Operating)
-5 to + 60
-20 to +70
°C
°C
RoHS Compliance RoHS Compliance
Item Symbol Conditions Values Unit Note
Min. Typ. Max.
Viewing angle
θ L (CR ≥10 ) 60 70 -- degree 1, 2
θ R60 70 --
θ U60 70 --
θ D40 50 --

3 IDK-1110W User Manual
Chapter 1 Overview
1.3.1 Measuring Condition
Measuring surrounding: dark room
Ambient temperature: 25±2°
15 min. warm-up time
1.3.2 Measuring Equipment
The optical characteristics are measured in a dark room. After 30 minutes operation,
the optical properties are measured at the center point of the LCD screen. (Response
time is measured by a Photo detector TOPCON BM-7 of view: 1° / Height: 120 mm.)
Note1: Definition of viewing angle range
Note 2: Definition of Contrast Ratio
Contrast ratio is calculated with the following formula :
Contrast Ratio (CR)=(White) Luminance of ON ÷ (Black) Luminance of OFF
Note 3: Definition of Response time: Sum of TR and T
Response time TR Normal
θ=Φ=0°
-57msec3
TF - 2028msec
Contrast ratio CR 400 500 -- - 2
Color chromaticity WX 0.26 0.31 0.36 - 1, 4
WY 0.28 0.33 0.38 -
RX 0.54 0.59 0.64 -
RY 0.28 0.33 0.38 -
GX 0.29 0.34 0.39 -
GY 0.54 0.59 0.64 -
BX 0.11 0.16 0.21 -
BY 0.05 0.1 0.15 -
Luminance L 350 440 -- cd/m24
Luminance uniformity YU 70 -- -- % 5

IDK-1110W User Manual 4
Note 4: Definition of optical measurement setup
Note 5: Definition of brightness uniformity
(Min Luminance of 9 points)
Luminance uniformity =------------------------------------------------×100%
Note 6: Rubbing Direction (The different Rubbing Direction will cause the different
optimal view direction
Note 7: Condition: Ta=25°C, Life time is estimated data.
Definitions of failure:
1. LCM brightness becomes half of the minimum value.
2. LED doesn’t light normally.

5 IDK-1110W User Manual
Chapter 1 Overview
1.4 Block Diagram
Figure 1.1 TFT LCD module
1.5 Absolute Maximum Ratings
1.5.1 Absolute Max Rating
Item Symbol
Value
Unit Note
Min. Max.
LED Power Supply Volt-
age
VLED -0.3 15.0 V GND=0
Logic Supply Voltage VDD -0.3 5.0 V
Operating Temperature TOPA -5 60 °C
Storage Temperature TSTG -20 70 °C

IDK-1110W User Manual 6
1.6 Dimensions
1.6.1 Front view

7 IDK-1110W User Manual
Chapter 1 Overview
1.6.2 Rear view

IDK-1110W User Manual 8

Chapter 2
2Electrical
Characteristics

IDK-1110W User Manual 10
2.1 TFT LCD Module
Note VDD-dip condition:
When 2.7V≤VDD<3.0V, td≤10ms.
VDD>3.0V, VDD-dip condition should be same as VDD-turn-con condition.
2.1.1 Signal Electrical Characteristics
Note LVDS Signal Waveform.
Item Symbol
Value
Unit Note
Min. Typ. Max.
Power voltage VDD 3.0 3.3 3.6 V 1
Current of power supply IDD - 0.3 - A VDD=3.3V
Black Pattern
Power voltage for LED
driver
VLED 4.5 5 5.5 V
LED driver current of
power supply
ILED - 1.4 A VLED=5V
ADJ=100%
Parameter Symbol
Value
Unit Remark
Min. Typ. Max.
Differential Input
High Threshold
VTH - - 100 mV VCM=1.2V
Differential Input
Low Threshold
VTL -100 - -- mV
Input current IIN -10 - +10 uA
Differential input
Voltage
VID 0.2 - 0.6 V
Common Mode
Voltage Offset
VCM |VID|/2 1.25 2.4-
|VID|/2
V

11 IDK-1110W User Manual
Chapter 2 Electrical Characteristics
2.2 Backlight Unit
2.2.1 Parameter guideline for LED backlight
Following characteristics are measured under a stable condition using an inverter at
25°C (Room Temperature):
Note1 The constant current source is needed for white LED back-light driving.
When LCM is operated over 60 deg.C ambient temperature, the IL of the
LED back-light should be adjusted to 460mA max.
There are 6 Groups LED shown as below, VLEDA-LEDK=9.6V ,Ta=25°C
Note1 Condition: Ta=25°C, continuous lighting
Life time is estimated data. Definitions of failure:
1.LCM brightness becomes half of the minimum value.
2.LED doesn’t light normally.
When LCM is operated over 40°C ambient temperature, the ILED should be followed:
Parameter Symbol
Value
Unit Note
Min. Typ. Max.
LED Driver voltage VLED 4.5 5 5.5 V
Power Supply Current
For LED Driver
ILED - 1.4 - A VLED=5V
VADJ=3.3V
(duty 100%)
ADJ Input Voltage VADJ - 3.3 VLED V duty=100%
LED_EN Voltage VEN -3.3-V
LED voltage VAKL -9.610.8VI
L= 540mA,
Ta = 25° C
LED current IL- 540 - mA Note1
- 460 - mA Note1
LED Life Time - - 50K - Hour Note2

IDK-1110W User Manual 12

Chapter 3
3Signal Characteristics

IDK-1110W User Manual 14
3.1 Electrical Interface Connection
CN1 (Input signal): CSTAR DS100-430-H23 (equivalent JAE FI-XB30SSRL-HF16)
Pin No. Symbol Description Note
1 GND Ground
2 VDD 3.3V Power
3 VDD 3.3V Power
4 V_EDID 3.3V Power for EDID
5 NC No connection
6 CLK_EDID EDID Clock Input
7 DATA_EDID EDID Data Input
8 RXIN0- LVDS Signal - channel0-
9 RXIN0+ LVDS Signal+ channel0+
10 GND Ground
11 RXIN1- Data Input channel1-
12 RXIN1+ Data Input channel1+
13 GND Ground
14 RXIN2- Data Input channel2-
15 RXIN2+ Data Input channel2+
16 GND Ground
17 RXCLKIN- Data Input CLK-
18 RXCLKIN+ Data Input CLK+
19 GND Ground
20 NC No connection
21 NC No connection
22 GND Ground
23 GND Ground
24 NC No connection
25 NC No connection
26 NC No connection
27 NC No connection
28 NC No connection
29 NC No connection
30 NC No connection