Advantech MIC-3359 User manual

M
M
MI
I
IC
C
C-
-
-3
3
30
0
00
0
00
0
0
S
S
Se
e
er
r
ri
i
ie
e
es
s
s
USER’
’
’S
Manual
U
US
SE
ER
RS
S
M
Ma
an
nu
ua
al
l
Advantech CompactPCI®
Modular Industrial Compute
r
MIC-3359
6U CompactPCI® Intel®
Desktop Pentium® 4
&
Mobile Pentium® 4-M
Processor Board with VGA
on Board

MIC-3359 User Manual --- Page I
Copyright Notice
This document is copyrighted, 2005. All rights are reserved. The original
manufacturer reserves the right to make improvements to the products described in
this manual at any time without notice. No part of this manual may be reproduced,
copied, translated or transmitted in any form or by any means without the prior
written permission of the original manufacturer. Information provided in this manual
is intended to be accurate and reliable. However, the original manufacturer assumes
no responsibility for its use, nor for any infringements upon the rights of third parties
which may result from its use.
Acknowledgements
PICMG™, CompactPCI®and the PICMG™, CompactPCI®logos are trademarks of the
PCI Industrial Computers Manufacturers Group. All other product names or
trademarks are properties of their respective owners.
CE Notification
The MIC-3359, developed by Advantech Co., Ltd., has passed the CE test for
environment specifications when shielded cables are used for external wiring. We
recommend the use of shielded cables.
FCC
This device complies with the requirements in part 15 of the FCC rule: Operation is
subject to be following two conditions：
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may
cause undesired operation.
CAUTION!!
Danger of explosion if battery in correctly replaced. The battery need not to be
charged. Replace only with Advantech-specified batteries.

MIC-3359 User Manual --- Page II
Product warranty
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for one year from the date of
purchase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is
defective, it will be repaired or replaced at no charge during the warranty period. For
out-of-warranty repairs, you will be billed according to the cost of replacement
materials, service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1、Collect all the information about the problem encountered. For example, CPU
speed, Advantech products used, other hardware and software used, etc. Note
anything abnormal and list any on-screen messages you get when the problem
occurs.
2、Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3、If your product is diagnosed as defective, obtain an RMA (return merchandise
authorization) number from your dealer. This allows us to process your return
more quickly.
4、Carefully pack the defective product, a fully-completed Repair and Replacement
Order Board and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5、Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.

MIC-3359 User Manual --- Page III
Packing List
Before installation, ensure that the following materials have been received:
• 1 MIC-3359 all-in-one single board computer
• 1 Utility and user manual (PDF file) CD-ROM disc
• 1 CPU Heat sink (Assembled)
• 1 Thermal pad for Pentium 4-M CPU
• 1 Solder-side cover (Assembled)
• Several screws
• 1 warranty certificate document
If any of these items are missing or damaged, contact your distributor or sales
representative immediately.
Technical Support and Sales Assistance
If you have any technical questions about the MIC-3359 or any other Advantech
products, please visit our support website at:
! http://www.advantech.com.tw/support
For more information about Advantech's products and sales information, please visit:
! http://www.advantech.com

Contents
Contents................................................................................ IV
Tables ................................................................................... VI
Figures .................................................................................VII
1. Hardware Configuration ......................................................2
1.1 Introduction ..................................................................... 2
Single P2P Bridge....................................................................3
1.2 Specifications ................................................................... 4
1.3 Jumpers and Switches ....................................................... 7
1.3.1 Jumper Setting ............................................................ 7
1.3.2 Clear CMOS (JP4)......................................................... 9
1.3.3 Switch Setting ............................................................10
1.4 Connector Setting ............................................................12
1.5 Safety Precautions ...........................................................12
1.6 Installing the CPU and Heatsink..........................................13
1.7 Software Support .............................................................14
2. AWARD BIOS Setup ........................................................... 16
2.1 Entering Setup.................................................................16
2.1.1 Standard CMOS Setup .................................................17
2.1.2 Advanced BIOS Features Setup .....................................17
2.1.3 Advanced Chipset Features Setup..................................21
2.1.4 Integrated Peripherals .................................................24
MIC-3359 User Manual --- Page IV
2.1.5 Power Management Setup ............................................27

2.1.6 PNP/PCI Configuration Setup ........................................27
2.1.7 PC Health Status.........................................................29
2.1.8 Load Optimized Defaults ..............................................30
2.1.9 Set Password..............................................................30
2.1.10 Save and Exit Setup ..................................................30
2.1.11 Exit Without Saving ...................................................30
Appendix A Pin Assignments ...............................................32
A.1 J1 Connector ...................................................................32
A.2 J2 Connector ...................................................................33
A.3 J3 Connector ...................................................................34
A.4 J5 Connector ...................................................................35
A.5~A.7 On board jumpers and connectors ...............................36
A.8~A11 On board jumpers and connectors ..............................34
A.12~A16 On board jumper and connectors ..............................35
MIC-3359 User Manual --- Page V

Tables
Table 1-1 MIC-3359 jumper descriptions..................................... 7
Table 1-2 MIC-3359 switch descriptions...................................... 7
Table 1-3 JP2 jumper definition ................................................. 7
Table 1-4 JP3 jumper definition ................................................. 8
Table 1-5 JP5 jumper definition ................................................. 8
Table 1-6 JP7 jumper definition ................................................. 8
Table 1-7 JP8 jumper definition ................................................. 9
Table 1-8 JP4 definition ............................................................ 9
Table 1-9 SW1 & SW3 definition ...............................................10
Table 1-10 SW2 definition........................................................10
Table 1-11 MIC-3359 connector descriptions ..............................12
Table A . 1 J1 connector ...........................................................32
Table A . 2 J2 connector ...........................................................33
Table A . 3 J3 connector ...........................................................34
Table A . 4 J5 connector ...........................................................35
Tables A. 5 ~ A. 7 On board jumpers and connectors ..................36
Tables A. 8 ~ A.11 On board jumpers and connectors .................37
Tables A.12 ~ A.16 On board jumpers and connectors.................38
MIC-3359 User Manual --- Page VI

Figures
Figure 1-1 MIC-3359 functional block diagram............................. 6
Figure 1-2 MIC-3359 jumper, switch and connector locations........11
Figure 1-3 Complete assembly CPU and heatsink........................14
Figure 2-1 Setup program initial screen.....................................16
Figure 2-2 Standard CMOS setup screen....................................17
Figure 2-3 Advanced BIOS features setup screen........................18
Figure 2-4 Advanced Chipset features setup screen.....................21
Figure 2-5 Integrated Peripherals setup screen...........................24
Figure 2-6 Power management setup screen ..............................27
Figure 2-7 PNP/PCI configuration screen....................................28
Figure 2-8 PC Health setup screen ............................................29
MIC-3359 User Manual --- Page VII

MIC-3359 User Manual --- Page 1
1
Chapter
Hardware Configuration

1. Hardware Configuration
1.1 Introduction
The MIC-3359 is a 6U 8HP CompactPCI®SBC ideal for mission critical, demanding
industrial or military applications which require high performance as well as
endurance in harsh operating environments.
The MIC-3359 CompactPCI®CPU board is optimized for Intel®845GV chipset. It
supports both the Intel Desktop Celeron®and Pentium®4 processor up to 2.8 GHz,
and the mobile Pentium® 4 -M processor. The VGA is integrated in the Intel®845GV
chipset, and there are two DDR DIMM slots which can support system memory up to
2GB. The MIC-3359 uses the Intel 82562ET for 10/100 Mb Fast Ethernet, with an
option for the Intel®82551ER for 10/100 Mb Fast Ethernet which is pin-to-pin
compatible with the Intel®82540EM for Giga Ethernet. The Pericom PI7C8150MA MHz
PCI-to-PCI Bridge is designed for bus expansions, programmable data transfer rate
control, and frequency conversions.
To achieve the most cost effective combination for entry-level CT applications or entry
to mid-level industrial applications, you can use a MIC-3041L enclosure with a
MIC-3359 6U CPCI board and Intel Pentium IV processor without a rear I/O transition
board. This gives the best performance-price balance and produces the most
cost-effective solution.
High Performance Intel®Pentium®4 Processor-M, Intel®Desktop Pentium®
4 Processor, and Celeron® Processor
The MIC-3359 supports the Intel®Pentium® 4 processor-M 1.7 GHz and 2.2 GHz, the
Desktop Pentium®4 Processor, and the Celeron® Processor with either u-FCPGA
package or u-FCBGA package. Both Intel®Pentium® processor-M and Intel®Pentium®
processor have on-chip 512 KB L2 cache providing high performance. The Intel®
Celeron® processor has an on-chip 256KB L2 cache providing high performance. With
the support of a 400 MHz and 533 MHz front-side bus, the MIC-3359 can fulfill
customer’s expectations of price-performance computing capability.
MIC-3359 User Manual --- Page 2

Compact Mechanical Design
The MIC-3359 has a CPU heatsink specially designed for the mobile Intel®Pentium®
4-M and Intel®Pentium®4 processor, enabling the MIC-3359 to operate without a
cooling fan on the heat sink. It needs only cooled air from the chassis fans for
ventilation.
Single P2P Bridge
The MIC uses the Pericom PI7C8150MA MHz PCI-to-PCI Bridge, which designed for
bus expansions, programmable data transfer rate control, and frequency conversions.
The Pericom Bridge can drive up to seven PCI slots in master mode, including those
using bus master cards. Up to eight MIC-3359 units can be installed in one enclosure.
Complete I/O Functions
MIC-3359 User Manual --- Page 3
The MIC-3359 offers all the I/O functions of an industrial computer with the rugged
Euroboard form factor. Output cables are fully connected to the rear I/O module via
user-define connectors (J3 and J5) on the backplane. The I/O panel contains two
10/100 base Ethernet ports (one of them is optional ), two COM ports, two USB 2.0
ports, one VGA connector, one PS/2 keyboard port, one PS/2 mouse port, and one
parallel port. The front panel also has a reset button and LEDs for power status and
HDD operation. The built-in high speed IDE controller provides two separate IDE
channels with Ultra DMA/33/66/100 mode. One is for CF on board, and the other one
is for IDE devices. The user-defined J3 connector is designed to support one IDE
device, one floppy drive, one printer device, and one or two Ethernet networks. These
drives can simply be connected to the backplane or to the rear transition board for
easy service and maintenance.

1.2 Specifications
Standard SBC Functions
•CompactPCI Bus Interface
PICMG 2.0 Rev. 3.0 compatible, 5V signaling; 32 bit/33 MHz, REQ/GNT for 7 slots;
Operates in system slot as system master
• CPU: Intel®Pentium®4 / Intel®Celeron®, 478-pin package FC-PGA
Mobile Pentium 4 Processor-M from 1.2 GHz up to 2.2 GHz for low power
dissipation (higher frequencies on request), Desktop Pentium 4 from 2 GHz up to 2.8
GHz for high performance, 512 KB full speed L2 on-die cache, 400 MHz and 533 MHz
processor front-side bus, passive heat sink for the processor, at least 300 LFM forced
air cooling required in the chassis.
• BIOS: 4 Mb Firmware Hub (FWH) using Award BIOS
• Chipset: Intel®845GV/ICH4 Chipset
Host Interface Support for Intel processor in an mPGA478 package
Hyper-Threading Technology support
Support Hub Interface 1.5 (266 MB/s point-to-point Hub Interface to the ICH4)
Integrated Graphics, core frequency of 200 MHz, resolution up to 2048 x 1536 x 60Hz
x 8 bit, shared memory up to 64MB
• Front Side Bus: 400MHz/533 MHz (Intel®Pentium®4 processor-M Processor)
• Bus Interface: 32-bit/33 MHz, PICMG 2.16 compliant
• Memory: Double Data Rate (DDR) SDRAM Configuration
Up to 2.0 GB of 200 MHz or 266 MHz DDR SDRAM
Two DDR DIMMs, single-sided and/or double-sided, DDR 200/266 unregistered,
184-pin non-ECC DDR
• Ethernet: the MIC-3359 uses the Intel@82562ET LAN chip for 10/100 Mb Fast
Ethernet, with an option for the Intel® 82551ER 10/100 Mb for Fast Ethernet which is
pin-to-pin compatible with the Intel® 82540EM 10/100/1000 Mb for Giga Ethernet.
MIC-3359 supports one 10/100Mb LAN; MIC-3359-A supports two 10/100Mb LANs;
MIC-3359-B supports one 10/100Mb LAN, and one Gb LAN.
MIC-3359 User Manual --- Page 4
• Enhanced IDE interface: The IDE interface supports two channels. The master for
the primary channel is reserved for the Compact Flash. The secondary IDE channel
can be connected to a RIO module via the J3 connector. The interface supports PIO
mode 4 and ATA 33/66/100 mode.

• Serial ports: COM1 and COM2 port (support RS-232/422/485 interface)
• USB port: Supports up to six USB channels: two front, two rear, and two on board
for internal devices; USB specification 2.0/1.1 compatible
• CompactFlash®socket: one CompactFlash®type II socket on board.
• AC97’ Audio Interface:Mic-in, Line-in, Line-out
•LEDs: Indicate LAN activity and speed, one green LED for power status, one yellow
LED for IDE HDD status.
• FDD Connector
•Parallel Port
•PS/2 Port: One for keyboard and one for mouse
MIC-3359 User Manual --- Page 5
•Watchdog timer: Provides system reset, interrupt and NMI support via software
control. Time interval is from 1 to 255 seconds.

Functional Block Diagram
LED Reset
SW PS/2 COM2 RJ1RJ2USB
VGA
COM1
PARALELL AUDIO
VGA CON.
(Front Panel)
VGA
Switch
Intel MCH
845GV DDR DIMM * 2
DDR POWER +2.5V +1.25V +1.5V
USB PORTS * 2
Primary IDE (CF)
Secondary IDE
Intel
82801DB
ICH4
LAN2
82551ER(10/100)
or
82540EM (10/100/1000)
LAN1
82562ET
(10/100)
PCI to PCI Bridge
PI7C8150MA
Bypass
resistor
(Reserved)
J1 J2 J3 J5
CLK GENERATOR
ICS950211 VCORE & 1.2V
Intel P4 Intel P4-M Celeron
FDDLPT
COM1 & 2
(RS232/422/485)
PS/2
FWH
(BIOS)
CPLD &
PORT 80
SpeedStep
SUPER I/O
Winbond
W83627HF
RJ45
RJ45
FSB 100/133 MHz
DDR 266/333
USB 2.0
ATA 33/66/100
HUB 1.5
PCI 32bits 33MHz
PCI 32bit
LPC
FDD LPT Sec. IDE COM1 & 2
LAN1 & 2
VGA USB
MIC-3359 User Manual --- Page 6
Figure 1-1 MIC-3359 functional block diagram

1.3 Jumpers and Switches
Table 1-1 and Table 1-2 list the jumper and switch functions. Figure 1-2 illustrates the
jumper and switch locations. Read this section carefully before changing the jumper
and switch settings on your MIC-3359 board.
Tab le 1 -1 MIC-3359 jumper descriptions
Number Function
JP2 VGA Output Setting
JP3 CPU Speed Setting
JP4 Clear CMOS
JP5 CF Mode Setting
JP7 COM2 Setting
JP8 COM1 Setting
Tab le 1 -2 MIC-3359 switch descriptions
Number Function
SW1 & SW3 CPU setting
SW2 Reset Button
1.3.1 Jumper Settings
Tab le 1 -3 JP2 jumper definition
JP2 - VGA Output Settings
Default Front Panel
Rear I/O
MIC-3359 User Manual --- Page 7

Tab le 1 -4 JP3 jumper definitions
JP3 - CPU Speed Settings
Default CPU Select
100MHz
133MHz
Tab le 1 -5 JP5 jumper definition
JP5 - CF Mode Settings
Default Master
Slave
Tab le 1 -6 JP7 jumper definition
JP7 – COM2 Settings
Default RS232 RS422 RS485
MIC-3359 User Manual --- Page 8

Tab le 1 -7 JP8 jumper definition
JP8 – COM1 Settings
Default RS232 RS422 RS485
1.3.2 Clear CMOS (JP4)
This jumper is used to erase CMOS data and reset the system BIOS information.
Follow the procedures below to clear the CMOS.
1、Turn off the system.
2、Close jumper JP4 (2-3) for about 3 seconds.
3、Set jumper JP4 as Normal.
4、Turn on the system. The BIOS is reset to its default setting.
Tab le 1 -8 JP4 definition
JP4 – Clear CMOS
Default Normal
Clear CMOS
MIC-3359 User Manual --- Page 9

1.3.3 Switch Settings
Tab le 1 -9 SW1 & SW3 definition
SW1 & SW3 – CPU Settings
SW3 SW1
Default P4、Celeron
SW3 SW1
P4-M
Table 1-10 SW2 definition
SW2 – Reset Button
PUSH Reset System
MIC-3359 User Manual --- Page 10

MIC-3359 User Manual --- Page 11
Figure 1-2 MIC-3359 jumper, switch, and connector locations

1.4 Connector Setting
On-board connectors link to external devices such as hard disk drives, keyboards, or
floppy drives, etc. Table 1-11 lists the function of each connector and Figure 1-2
illustrates each connector location.
Table 1-11 MIC-3359 connector descriptions
Number Function
CN1 FDD Connector
CN2 V(I/O) Setting
CN3 IDE Connector (Secondary IDE)
CN4 CompactFlash™ Connector (Primary IDE)
CN6 USB Port (Internal)
CN7 Internal COM2 Connector
CN8 LPT Connector
CN9 PS/2 Mouse/Keyboard Connector
CN10 USB Port*2
CN12 VGA Connector
CN13 COM1 Connector
CN14 COM2 Connector
JP10 AC’97 Connector
RJ1 LAN1 Connector
RJ2 LAN2 Connector (82551ER)
RJ2 LAN2 Connector (82540EM)
J1/J2 Primary CompactPCI®bus
J3/J5 Rear I/O transition
LED IDE LED and Power LED
1.5 Safety Precautions
Follow these simple precautions to protect yourself from harm and the products from
damage.
1、To avoid electric shock, always disconnect the power from your PC chassis
before you work on it. Don’t touch any components on the CPU board or other
boards while the PC is on.
MIC-3359 User Manual --- Page 12
2、Disconnect power before making any configuration changes. The sudden rush