Advantech MIO-2263 User manual

User Manual
MIO-2263
Intel® Atom™ SoC J1900/E3825
Pico-ITX SBC, DDR3L, 18/24-bit
LVDS, VGA or HDMI, 1 GbE, Half-
size Mini PCIe, 4 USB, 2 COM,
SMBus, mSATA & MIOe

MIO-2263 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2014
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements
of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of AMI Software International, Inc.
Intel® is a trademark of Intel® Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel and Atom® are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective owners.
Part No. 2006226312 Edition 3
Printed in China July 2015

iii MIO-2263 User Manual
Product Warranty (1 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

MIO-2263 User Manual iv
Packing List
Before installation, please ensure the following items have been shipped:
Item Part Number
1 MIO-2263 SBC
1 Startup manual
Cables
Heatsink:
Stud & Screw
Ordering Information
Model Number Description
Optional Accessories
Part No. Description
1960065074N001 Heat Spreader (99.5 x 70.5 x 11.2 mm)
Part Number Description
1700006291 SATA cable 7P 30 cm w/ right angle
1700022444-01 Audio Cable 2*5P-2.0/JACK*2 20cm
1701200220 COM PORT cable 2*10P-2.0/D-SUB 9P(M)*2 22 cm
1700019656 SATA Power cable 5P-1.25/5P-2.0+SATA 5P 15 cm
1700002172 USB cable 2.0mm pitch USB-A(F) 17cm
1700019705 AT Power cable 12cm
1960063455T001 99.5 x 70.5 x 15.7 mm
Part Number Description
9666226300E Stud and screw pack, including:
1935031500 Screw R/S D=5.3 H=2 + M3*15L, 4 pcs
1910002596-01 Stud F=M3*10L M=M3*5L B=5 H=19, 4 pcs
193B0204C0 Screw F/S D=3.5 H=0.8 + M2*4L, 2 pcs
MIO-2263J-U0A1E Intel® Atom™ SoC J1900, fanless, LVDS, VGA, Gigabit
Ethernet, 4 USB, mSATA, SMBus, GPIO, 2 COM, mini PCIe,
MIOe
MIO-2263JH-U0A1E Intel® Atom™ SoC J1900, fanless, LVDS, HDMI, Gigabit
Ethernet, 4 USB, mSATA, SMBus, GPIO, 2 COM, mini PCIe,
MIOe
MIO-2263E-S3A1E Intel Atom SoC E3825, fanless, LVDS, VGA, Gigabit Ether-
net, 4 USB, mSATA, SMBus, GPIO, 2 COM, mini PICe, MIOe

v MIO-2263 User Manual
Declaration of Conformity
This device complies with the requirements in part 15 of the FCC rules: Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation
FCC Class A
This equipment has been tested and found to comply with the limits for a Class A dig-
ital device, pursuant to Part 15 of the FCC Rules. These limits are designed to pro-
vide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this device in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense. The
user is advised that any equipment changes or modifications not expressly approved
by the party responsible for compliance would void the compliance to FCC regula-
tions and therefore, the user's authority to operate the equipment.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.

MIO-2263 User Manual vi
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

vii MIO-2263 User Manual
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

MIO-2263 User Manual viii

ix MIO-2263 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ...............................................................................................2
1.2 Specifications............................................................................................2
1.2.1 General Specifications..................................................................2
1.2.2 Functional Specifications..............................................................3
1.2.3 Mechanical Specifications.............................................................4
1.2.4 Electrical Specifications................................................................4
1.2.5 Environmental Specifications........................................................5
1.3 Function Block Diagram............................................................................5
Chapter 2 H/W Installation....................................7
2.1 Jumpers ....................................................................................................8
2.1.1 Jumper Description.......................................................................8
2.1.2 Jumper List ...................................................................................8
Table 2.1: Jumper List.................................................................8
2.1.3 Jumper Settings............................................................................8
Table 2.2: J1: LCD Power/Auto Power on...................................8
2.2 Connectors................................................................................................9
2.2.1 Connector List...............................................................................9
2.2.2 Connector Settings .......................................................................9
2.3 Mechanical..............................................................................................12
2.3.1 Jumper and Connector Locations...............................................12
Figure 2.1 Jumper and Connector layout (Top side).................12
Figure 2.2 Jumper and connector layout (Bottom side).............12
2.3.2 Board Dimensions.......................................................................13
Figure 2.3 Board dimension layout (Top side)...........................13
Figure 2.4 Board dimension layout (Bottom side)......................13
Figure 2.5 Board dimension layout (coastline with power connec-
tor and heatsink).......................................................14
Figure 2.6 Board dimension layout (coastline with Power connec-
tor and optional heatspreader) .................................14
Figure 2.7 Board dimension layout (coastline with optional DC/
jack)..........................................................................14
Figure 2.8 MI/O module height constraints................................15
Figure 2.9 Illustration of heat spreader assembly.....................16
Chapter 3 BIOS Settings.....................................17
3.1 BIOS Setup .............................................................................................18
3.2 Entering Setup ........................................................................................19
3.2.1 Main Setup..................................................................................19
3.2.2 Advanced BIOS Features Setup.................................................20
3.2.3 Chipset Configuration .................................................................34
3.2.4 Security.......................................................................................43
3.2.5 Boot.............................................................................................44
3.2.6 Save & Exit .................................................................................45
Chapter 4 S/W Introduction & Installation ........47
4.1 S/W Introduction......................................................................................48
4.2 Driver Installation ....................................................................................48

MIO-2263 User Manual x
4.2.1 Windows 7 Professional ............................................................. 48
4.2.2 Other OS..................................................................................... 48
4.3 Value-Added Software Services............................................................. 48
4.3.1 SUSI Introduction........................................................................ 48
4.3.2 Software APIs............................................................................. 49
4.3.3 SUSI Installation......................................................................... 50
4.3.4 SUSI Sample Programs.............................................................. 51
Appendix A PIN Assignments .............................. 59
A.1 Jumper Setting........................................................................................ 60
Table A.1: Jumper List............................................................... 60
A.2 Connectors.............................................................................................. 60
Table A.2: Connectors............................................................... 60
Table A.3: J1: LCD Power/Auto Power On................................ 60
Appendix B WDT & GPIO ...................................... 81
B.1 Watchdog Timer Sample Code............................................................... 82
B.2 GPIO Sample Code................................................................................ 83
Appendix C System Assignments........................ 85
C.1 System I/O Ports..................................................................................... 86
Table C.1: System I/O Ports ...................................................... 86
C.2 1st MB Memory Map............................................................................... 86
Table C.2: 1st MB Memory Map................................................ 86
C.3 Interrupt Assignments............................................................................. 87
Table C.3: Interrupt assignments............................................... 87

Chapter 1
1General Introduction
This chapter gives background
information on the MIO-2263.
Sections include:
Introduction
Product Features
Specifications

MIO-2263 User Manual 2
1.1 Introduction
MIO-2263 is a MI/O-Ultra SBC (Single Board Computer) with Embedded Intel®
Atom™ SoC J1900 2.0 GHz and E3825 1.33 GHz Processor. The MIO-2263 can
support DDR3L memory up to 8 GB, has one USB 3.0 and 3 USB2.0 compatible
ports, one GbE (up to 1000 Mbps) interface, LVDS and VGA or HDMI support, HD
(High Definition) audio, and one half size mini-PCIe and MIOe expansion slot. In
addition, MIO-2263 also supports one SATA drive, two COM ports, SMBus, one
GPIO and one half size mSATA slot. Advantech's innovative MI/O (multiple I/O)
Extension SBC is equipped with flexible multiple I/O to assist integrators in develop-
ing optimized solutions.
1.2 Specifications
1.2.1 General Specifications
CPU: Intel® Atom™ SoC processor J1900/ E3825
System Chipset Intel® Atom™ SoC J1900/ E3825
BIOS: AMI EFI 64 Mbit Flash BIOS
System Memory: DDR3L, 1333 MHz for J1900, 1066 MHz for E3825, up to 8
GB
Watchdog Timer: Single chip Watchdog 255-level interval timer, setup by soft-
ware
Expansion Interface:
–1 x half size mini-PCIe slot
–1 x MIOe connector: supports 2 x USB 2.0, 2 x PCIe x1, LPC, HD Audio line-
out, SMBus, DP (or HDMI, supported by request), 5 Vsb/12 Vsb power
Battery: Lithium 3 V / 210 mAH
I/O
Internal I/O interface: 2 x USB2.0, 1 x RS-232, 1 x RS-232/422/485, 1 x HD
Audio (line in, line out), GPIO, SMBus
Rear I/O ports: 1 x RJ45 Ethernet, 1 x VGA or HDMI, 1 x USB 3.0, 1 x USB 2.0,
1 x Power connector (or DC jack, supported by request):
Ethernet
Controller: Intel i210 (GbE1)
Speed: 10/100/1000 Mbps
Connector: 1 x RJ45
Standard: Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.ab
Support wake-on-LAN
Display
Controller: Intel® Atom™ SoC J1900/ E3825, Directx* 11 and OpenGL 3.0
support
Resolution:
–VGA: 1920 x 1200
–LVDS: 18/24-bit LVDS1, up to 1440 x 900
–HDMI: 1920 x 1080

3 MIO-2263 User Manual
Chapter 1 General Introduction
1.2.2 Functional Specifications
Processor
Chipset
Processor
Intel® Atom™ SoC Processor J1900/ E3825
Frequency
–J1900 2.0 GHz/ CPU Burst 2.42 GHz
–E3825 1.33 GHz
Manufacturing Technology: 22 nm
L2 cache: 2 MB (J1900)/ 1 MB (E3825)
Memory
Supports DDR3L, 1333 MHz (J1900), DDR3L 1066 MHz
(E3825), up to 8 GB
SODIMM Socket: 204-pin SODIMM socket type *1
Graphic Engine
Directx* 11, OGL 3.0, OCL 1.1, OGL ES 2.0
Hardware decode/ acceleration:
–Encode: H264, MPEG2/4, VC1, WMV9
–Decode: H264, MPEG2
Display
VGA: 1920 x 1200 @ 60 Hz
HDMI: 1920 x 1080
LVDS1: 18/24-bit, up to 1440 x 900 @ 60 Hz
Dual independent display: LVDS + VGA or HDMI + LVDS
Control Hub Intel® Atom SoC processor J1900/ E3825
Audio
High Definition Audio (HD) ALC-888S codec
Up to 2 channel of PCM (Pulse Code Modulation) audio out-
put
Connectors: Line-out, Line-in
PCI-Express Interface
4 PCI-Express x1 Lanes
Lane 1 &2 : MIOe connector
Lane 3: Half-size Mini PCIe connector
Lane 4: Intel i210 GbE controller
SATA Interface 1 x mSATA by mini-PCIe socket
1 x SATAII (Max. Data transfer Rate 300 MB/s)
USB Interface
2 x internal USB ports
2 x rear I/O ports at coastline (one USB 2.0 + one USB 3.0)
Transmission speed up to 480 Mbps (USB 2.0) / 5 Gbps
(USB 3.0)
Power Management
Full ACPI (Advanced Configuration and Power Interface) 3.0
Supports S0, S3, S4, S5
Support wake on LAN
BIOS AMI EFI 64 Mbit Flash BIOS via SPI

MIO-2263 User Manual 4
Others
1.2.3 Mechanical Specifications
1.2.3.1 Dimensions (mm)
L100 mm x W72 mm (3.9" x 2.8")
1.2.3.2 Height on top (mm)
15.7 mm (Heatsink)
1.2.3.3 Height under bottom (mm)
16.34 mm (Rear I/O USB)
1.2.3.4 Weight (g)
0.46 kg (1.01 lb, weight of total package)
1.2.4 Electrical Specifications
Power Supply Type: Single 12 V DC power input (support DC power hot plug)
1.2.4.1 Power supply Voltage
Single 12 V input 10%
Total peripheral power supply output: 5 V @ 3 A for CPU board and MIOe mod-
ule totally, 12 V @ 2 A for MIOe module
1.2.4.2 Power Consumption
Typical in Windows 8 Idle Mode:
J1900: 0.85 A @ 12 V (10.2 W)
E3825: 0.59 A @ 12 V (7.08 W)
Max in Windows 8 HCT12 (10 minutes):
J1900: 1.04 A @ 12 V (12.48 W)
E3825: 0.76 A @ 12 V (9.12 W)
1.2.4.3 RTC Battery
Typical Voltage: 3.0 V
Normal discharge capacity: 210 mAh
Ethernet
Controller: Intel® i210 (GbE1)
Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE
802.ab
Support 10/100/1000 Mbps
Connectors: RJ45
LAN1 LED
–Link: Green (100Mbps)/ Orange (1000Mbps)
–Active: Green (flash)
Support wake on LAN
Serial ports Controller: SMSC SCH 3114 1 x RS-232 / 1 x 232/422/485 serial ports with ESD protection:
air gap ± 15 kV, contact ± 8 kV
GPIO
Controller: SMSC SCH 3114
8-Bit (programming) through Super I/O, pin header
5 V tolerance
SMBus Default is SMBus

5 MIO-2263 User Manual
Chapter 1 General Introduction
1.2.5 Environmental Specifications
1.2.5.1 Operating Humidity
40 °C @ 95% RH Non-Condensing
1.2.5.2 Operating Temperature
0 ~ 60 °C (32~140 °F)
1.2.5.3 Storage Humidity
60 °C @ 95% RH Non-Condensing
1.2.5.4 Storage Temperature
-40 ~ 85 °C (-40 ~ 185 °F)
1.3 Function Block Diagram
DDI Port 1
DP/HDMI
DDR3L 1333/1066
SO-DIMM up to 8GB
Super I/O
Intel Atom SoC
E3825 / J1900
Single
Channel
LPC
2 x USB2.0
Half size Mini PCIe PCIe x 1
USB2.0
Half size mSATA SATAII 300MB/s
1 x SATA II SATAII 300MB/s
VGA
RGB
HDMI
DDI0
SMBus
2 PCIe x1
HD Audio Line-out
2 x USB2.0
LPC
12Vsb/5Vsb
Reset
Transmitter
USB Hub
MIOe
1 x USB 3.0 USB2.0/USB3.0
1 x USB 2.0 USB2.0
AMI BIOS SPI
ALC888S
2 x USB 2.0
18/24 bit LVDS
HD Audio
SMBus
Intel i210 PCIe x1
SMBus
8-bit GPIO
COM1: RS-232/422/485
COM2: RS-232
Watchdog Timer
Line-in
Line-out
RJ45

MIO-2263 User Manual 6

Chapter 2
2H/W Installation
This chapter explains the setup
procedures of the MIO-2263 hard-
ware, including instructions on
setting jumpers and connecting
peripherals, as well as switches,
indicators and mechanical draw-
ings. Be sure to read all safety
precautions before you begin the
installation procedure.

MIO-2263 User Manual 8
2.1 Jumpers
2.1.1 Jumper Description
Cards can be configured by setting jumpers. A jumper is a metal bridge used to close
an electric circuit. It consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To close a jumper, you
connect the pins with the clip. To open a jumper, you remove the clip. Sometimes a
jumper will have three pins, labeled 1, 2 and 3. In this case you would connect either
pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows.
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes.
Generally, you simply need a standard cable to make most connections.
2.1.2 Jumper List
2.1.3 Jumper Settings
Warning! To avoid damaging the computer, always turn off the power supply
before setting jumpers.
Table 2.1: Jumper List
J1 LCD Power / Auto Power on
Table 2.2: J1: LCD Power/Auto Power on
Part Number 1653003260
Footprint HD_3x2P_79
Description PIN HEADER 3*2P 180D(M) 2.0mm SMD SOUARE PIN
Setting Function
(1-2) +5V
(3-4) (default) +3.3V
(5-6) (default) Auto Power On

9 MIO-2263 User Manual
Chapter 2 H/W Installation
2.2 Connectors
2.2.1 Connector List
2.2.2 Connector Settings
2.2.2.1 Battery Connector (BH1)
MIO-2263 supports Lithium 3 V/210 mAH CR2032 battery with wire via battery con-
nector (BH1).
2.2.2.2 12 V Power Input Connector (CN1)
Main power connector supports single 12 V input, and there's an optional choice of
DC/Jack (CN2, co-layout with 2pin power connector)
2.2.2.3 DDRIII SODIMM Socket (CN6)
One 204-pin/H9.2 mm DDRIII DIMM socket supports DDR3L 1333 MHz (J1900)/
1066 MHz (E3825) up to 8 GB.
CN1 12 V Power Input
CN2 DC JACK (by request)
CN3 12 V Power Input (2 x 3 pin support by request)
CN6 DDR3 SO-DIMM
CN9 GPIO
CN11 VGA
CN12 HDMI
CN13 Front Panel
CN14 SATA
CN15 mSATA
CN16 Mini PCIe
CN18 Internal USB
CN19 External USB 3.0 + USB 2.0
CN20 COM1/COM2
CN24 Gigabit Ethernet
CN27 HD Audio
CN29 MIOe
CN30 Inverter Power/Internal SATA Power
CN31 18/24 bits LVDS Panel
CN33 SMBus
BH1 Battery
Note! How to clear CMOS: (Must follow below steps)
1. Turn off system power
2. Unplug CR2032 battery cable on BH1
3. Waiting for 15sec or short BH1 pin1-2
4. Connect battery cable on BH1
5. Turn on system power

MIO-2263 User Manual 10
2.2.2.4 GPIO (General Purpose Input Output) (CN9)
The board supports 8-bit GPIO (5 V tolerance) through GPIO pin header. The 8 digi-
tal inputs and outputs can be programmed to read or control devices, with each input
or output defined.
2.2.2.5 VGA/ HDMI/ LVDS Interface Connections (CN11/ CN12/ CN31)
The MIO-2263's display interface support either VGA or HDMI on rear IO and is
capable of driving a wide range of flat panel displays, including passive LCD and
active LCD displays.The board has three kinds of connector types to support these
displays: one is on rear IO support either standard CRT VGA monitors or high defini-
tion HDMI display and one for LVDS type LCD panels.
CRT display connector (CN11)
The CRT display 15pins connector is a rear I/O connector on coastline used for con-
ventional CRT displays. Resolution: up to 1920 x 1200.
HDMI display connector (CN12)
MIO-2263 also support HDMI display output, meet HDMI1.4a specification. Resolu-
tion: up to 1920 x 1080.
LVDS LCD panel connector (CN31)
The board supports single channel 18/24-bit LVDS LCD panel displays via 14*1pin
wafer box. Resolution: up to 1400 x 900.
2.2.2.6 Front Panel Connector(CN13)
MIO-2263 integrates below functions as front panel 6pin connector.
Power button
Supports power on/off button in ATX mode.
Reset
If you install a reset switch, it should be an open single pole switch. Momentarily
pressing the switch will activate a reset.
Power LED
Power LED indicator would light when power is on.
HDD LED
HDD LED indicator for hard disk access is an active low signal
2.2.2.7 SATA Connector (CN14)
MIO-2263 features one high performance Serial ATA interfaces. Data transfer rates
up to 300 MB/s enabling very fast data and file transfer, and independent DMA oper-
ation on two ports.
2.2.2.8 mSATA Connector (CN15)
MIO-2263 provides a half size mini-PCIe socket which integrates SATAII signals,
supports mSATA interface modules.
2.2.2.9 Mini PCIe Connector (CN16)
MIO-2263 supports a half size mini PCIe slot. PCI Express Mini Card (also known as
Mini PCI Express, Mini PCIe, and Mini PCI-E) is a replacement for the Mini PCI form
factor based on PCI Express. It is developed by the PCI-SIG. The host device sup-
ports both PCI Express and USB 2.0 connectivity.
2.2.2.10 USB Connectors (CN18 and CN19)
The board provides four USB (Universal Serial Bus) ports, two are rear I/O on coast-
line (CN19); and the other two are internal USB ports (CN18). The rear I/O USB port
support one USB 3.0 port and one USB 2.0. The USB 3.0 port comply with USB