Advantech MIO-2360 SBC User manual

The information contained in this document has been carefully researched and is, to the best
of our knowledge, accurate. However, we assume no liability for any product failures or
damages, immediate or consequential, resulting from the use of the information provided
herein. Our products are not intended for use in systems in which failures of product could
result in personal injury. All trademarks mentioned herein are property of their respective
owners. All specifications are subject to change without notice.
Manual
ADVANTECH
MIO-2360

User Manual
MIO-2360
Intel® Pentium N4200/Celeron
N3350/Atom™ E3940/Atom™
E3930 Pico-ITX SBC, DDR3L,
24-bit LVDS, VGA/HDMI, 1 GbE,
Full-size Mini PCIe, 4 USB, 2
COM, SMBus, mSATA & MIOe

MIO-2360 User Manual ii
Copyright
The documentation and the software included with this product are copyrighted 2017
by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right
to make improvements in the products described in this manual at any time without
notice.
No part of this manual may be reproduced, copied, translated or transmitted in any
form or by any means without the prior written permission of Advantech Co., Ltd.
Information provided in this manual is intended to be accurate and reliable. However,
Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements
of the rights of third parties, which may result from its use.
Acknowledgements
AMI is a trademark of AMI Software International, Inc.
Intel® is a trademark of Intel® Technologies, Inc.
IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Cor-
poration.
Intel and Atom® are trademarks of Intel Corporation.
Microsoft Windows® is a registered trademark of Microsoft Corp.
RTL is a trademark of Realtek Semi-Conductor Co., Ltd.
ESS is a trademark of ESS Technology, Inc.
UMC is a trademark of United Microelectronics Corporation.
SMI is a trademark of Silicon Motion, Inc.
Creative is a trademark of Creative Technology LTD.
All other product names or trademarks are properties of their respective owners.
Part No. 2006236010 Edition 1
Printed in China Sep 2017

iii MIO-2360 User Manual
Product Warranty (2 years)
Advantech warrants to you, the original purchaser, that each of its products will be
free from defects in materials and workmanship for two years from the date of pur-
chase.
This warranty does not apply to any products which have been repaired or altered by
persons other than repair personnel authorized by Advantech, or which have been
subject to misuse, abuse, accident or improper installation. Advantech assumes no
liability under the terms of this warranty as a consequence of such events.
Because of Advantech’s high quality-control standards and rigorous testing, most of
our customers never need to use our repair service. If an Advantech product is defec-
tive, it will be repaired or replaced at no charge during the warranty period. For out-
of-warranty repairs, you will be billed according to the cost of replacement materials,
service time and freight. Please consult your dealer for more details.
If you think you have a defective product, follow these steps:
1. Collect all the information about the problem encountered. (For example, CPU
speed, Advantech products used, other hardware and software used, etc.) Note
anything abnormal and list any onscreen messages you get when the problem
occurs.
2. Call your dealer and describe the problem. Please have your manual, product,
and any helpful information readily available.
3. If your product is diagnosed as defective, obtain an RMA (return merchandize
authorization) number from your dealer. This allows us to process your return
more quickly.
4. Carefully pack the defective product, a fully-completed Repair and Replacement
Order Card and a photocopy proof of purchase date (such as your sales receipt)
in a shippable container. A product returned without proof of the purchase date
is not eligible for warranty service.
5. Write the RMA number visibly on the outside of the package and ship it prepaid
to your dealer.
Technical Support and Assistance
1. Visit the Advantech web site at www.advantech.com/support where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
–Product name and serial number
–Description of your peripheral attachments
–Description of your software (operating system, version, application software,
etc.)
–A complete description of the problem
–The exact wording of any error messages

MIO-2360 User Manual iv
Packing List
Before installation, please ensure the following items have been shipped:
Item Part Number
1 MIO-2360 SBC
1 Startup manual
Cables
Heatsink:
Stud & Screw
Ordering Information
Model Number Description
Optional Accessories
Part No. Description
TBD Heat Spreader
Part Number Description
1700006291 SATA cable 7P 30 cm w/ right angle
1700022444-01 Audio Cable 2*5P-2.0/JACK*2 20cm
1701200220 COM PORT cable 2*10P-2.0/D-SUB 9P(M)*2 22 cm
1700027546-01 A cable 1*5P-2.0/1*5P-2.0+SATA 15P 15cm MIO-236
1700002172 USB cable 2.0mm pitch USB-A(F) 17cm
1700019705 AT Power cable 12cm
1960078695T001 99.5 x 70.5 x 15.7 mm
Part Number Description
9666226300E Stud and screw pack, including:
1935031500 Screw R/S D=5.3 H=2 + M3*15L, 4 pcs
1910002596-01 Stud F=M3*10L M=M3*5L B=5 H=19, 4 pcs
193B0204C0 Screw F/S D=3.5 H=0.8 + M2*4L, 2 pcs
MIO-2360N-S1A1E Intel® Celeron SoC N3350, fanless, LVDS, VGA/HDMI, Giga-
bit Ethernet, 4 USB, mSATA, SMBus, GPIO, 2 COM, Mini
PCIe, MIOe
MIO-2360N-S2A1E Intel® Pentium SoC N4200, fanless, LVDS, VGA/HDMI,
Gigabit Ethernet, 4 USB, mSATA, SMBus, GPIO, 2 COM,
Mini PCIe, MIOe
TBD Intel® Atom™ SoC E3940, fanless, LVDS, VGA/HDMI, Giga-
bit Ethernet, 4 USB, mSATA, SMBus, GPIO, 2 COM, Mini
PCIe, MIOe
TBD Intel® Atom™ SoC E3930, fanless, LVDS, VGA/HDMI, Giga-
bit Ethernet, 4 USB, mSATA, SMBus, GPIO, 2 COM, Mini
PCIe, MIOe

v MIO-2360 User Manual
Declaration of Conformity
This device complies with the requirements in part 15 of the FCC rules: Operation is
subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interfer-
ence to radio or television reception, which can be determined by turning the equip-
ment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommended by the man-
ufacturer. Discard used batteries according to the manufacturer's
instructions.

MIO-2360 User Manual vi
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp
cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equip-
ment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting
it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment
from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source
to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be
opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service
personnel:
The power cord or plug is damaged.
Liquid has penetrated into the equipment.
The equipment has been exposed to moisture.
The equipment does not work well, or you cannot get it to work according to
the user's manual.
The equipment has been dropped and damaged.
The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE
STORAGE TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60° C
(140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT
SHOULD BE IN A CONTROLLED ENVIRONMENT.
16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY
REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE
RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES
ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.
The sound pressure level at the operator's position according to IEC 704-1:1982 is
no more than 70 dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech
disclaims all responsibility for the accuracy of any statements contained herein.

vii MIO-2360 User Manual
Safety Precaution - Static Electricity
Follow these simple precautions to protect yourself from harm and the products from
damage.
To avoid electrical shock, always disconnect the power from your PC chassis
before you work on it. Don't touch any components on the CPU card or other
cards while the PC is on.
Disconnect power before making any configuration changes. The sudden rush
of power as you connect a jumper or install a card may damage sensitive elec-
tronic components.

MIO-2360 User Manual viii

ix MIO-2263 User Manual
Contents
Chapter 1 General Introduction ...........................1
1.1 Introduction ............................................................................................... 2
1.2 Specifications ............................................................................................ 2
1.2.1 General Specifications .................................................................. 2
1.2.2 Functional Specifications .............................................................. 3
1.2.3 Mechanical Specifications............................................................. 4
1.2.4 Electrical Specifications ................................................................ 4
1.2.5 Environmental Specifications........................................................ 5
1.3 Function Block Diagram ............................................................................ 5
Chapter 2 H/W Installation....................................7
2.1 Jumpers .................................................................................................... 8
2.1.1 Jumper Description ....................................................................... 8
2.1.2 Jumper List ................................................................................... 8
Table 2.1: Jumper List ................................................................. 8
2.1.3 Jumper Settings ............................................................................ 8
Table 2.2: J1: LCD Power/Auto Power on................................... 8
2.2 Connectors................................................................................................ 9
2.2.1 Connector List............................................................................... 9
2.2.2 Connector Settings ....................................................................... 9
2.3 Mechanical .............................................................................................. 12
2.3.1 Jumper and Connector Locations ............................................... 12
Figure 2.1 Jumper and Connector layout (Top side) ................. 12
Figure 2.2 Jumper and connector layout (Bottom side)............. 12
2.3.2 Board Dimensions....................................................................... 13
Figure 2.3 MIO-2360 Mechanical Drawing (Top Side) .............. 13
Figure 2.4 MIO-2360 Mechanical Drawing (Bottom Side) ......... 13
Figure 2.5 MIO-2360 Mechanical Drawing (Side View)............. 14
Figure 2.6 MIO-2360 Mechanical Drawing (Side View with Option-
al HDMI) ................................................................... 14
Figure 2.7 MI/O module height constraints................................ 15
Figure 2.8 Illustration of heat spreader assembly..................... 16
Chapter 3 BIOS Settings.....................................17
3.1 BIOS Setup ............................................................................................. 18
3.2 Entering Setup ........................................................................................ 19
3.2.1 Main Setup.................................................................................. 19
3.2.2 Advanced BIOS Features Setup................................................. 20
3.2.3 Chipset Configuration ................................................................. 33
3.2.4 Security ....................................................................................... 42
3.2.5 Boot............................................................................................. 43
3.2.6 Save & Exit ................................................................................. 44
Chapter 4 S/W Introduction & Installation ........45
4.1 S/W Introduction...................................................................................... 46
4.2 Driver Installation .................................................................................... 46
4.2.1 Windows 10 Professional............................................................ 46
4.2.2 Other OS..................................................................................... 46
4.3 Value-Added Software Services ............................................................. 46

MIO-2263 User Manual x
4.3.1 SUSI Introduction........................................................................ 46
4.3.2 Software APIs ............................................................................. 47
4.3.3 SUSI Installation ......................................................................... 48
4.3.4 SUSI Sample Programs.............................................................. 49
Appendix A PIN Assignments .............................. 57
A.1 Jumper Setting........................................................................................ 58
Table A.1: Jumper List............................................................... 58
A.2 Connectors.............................................................................................. 58
Table A.2: Connector list ........................................................... 58
Appendix B WDT & GPIO ...................................... 75
B.1 Watchdog Timer Sample Code............................................................... 76
B.2 GPIO Sample Code ................................................................................ 77
Appendix C System Assignments........................ 79
C.1 System I/O Ports..................................................................................... 80
Table C.1: System I/O Ports ...................................................... 80
C.2 1st MB Memory Map............................................................................... 80
Table C.2: 1st MB Memory Map ................................................ 80
C.3 Interrupt Assignments ............................................................................. 81
Table C.3: Interrupt assignments............................................... 81

Chapter 1
1General Introduction
This chapter gives background
information on the MIO-2360.
Sections include:
Introduction
Product Features
Specifications

MIO-2360 User Manual 2
1.1 Introduction
MIO-2360 is a MI/O-Ultra SBC (Single Board Computer) with Embedded Intel® Cel-
eron N3350/Atom™ E3940/Atom™ E3930 Processor. The MIO-2360 can support
DDR3L memory up to 8 GB, has 2 x USB 3.0 and 4 x USB 2.0 compatible ports, one
GbE (up to 1000 Mbps) interface, LVDS and VGA or HDMI support, HD (High Defini-
tion) audio, and one full size mini-PCIe and MIOe expansion slot. In addition, MIO-
2360 also supports one SATA drive, two COM ports, SMBus, one GPIO and one half
size mSATA slot. Advantech's innovative MI/O (multiple I/O) Extension SBC is
equipped with flexible multiple I/O to assist integrators in developing optimized solu-
tions.
1.2 Specifications
1.2.1 General Specifications
CPU: Intel® Pentium N4200/Celeron N3350/Atom™ E3940/Atom™ E3930
System Chipset Intel® Celeron/Atom SoC integrated
BIOS: AMI EFI 64 Mbit Flash BIOS
System Memory: DDR3L, 1866 MHz, up to 8 GB
Watchdog Timer: Single chip Watchdog 255-level interval timer, setup by soft-
ware
Expansion Interface:
–1 x full size mini-PCIe slot
–1 x MIOe connector: SMBus, 2 x USB3.0, LPC, 2 x PCIe x1, line out, Dis-
playPort/HDMI*, +5 Vsb/+12 Vsb power, Power On, Reset, SATA*
Battery: Lithium 3 V / 210 mAH
I/O
Internal I/O interface: 2 x USB2.0, 2 x RS-232/422/485, 1 x HD Audio (line in,
line out), GPIO, SMBus
Rear I/O ports: 1 x RJ45 Ethernet, 1 x VGA or HDMI, 2 x USB 3.0, 1 x Power
connector (or DC jack, supported by request)
Ethernet
Controller: Intel i210 (GbE1)
Speed: 10/100/1000 Mbps
Connector: 1 x RJ45
Standard: Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE 802.ab
Support wake-on-LAN
Display
Controller: Intel® SoC N3350/E3940/E3930, DirectX 11 and OpenGL3.0 sup-
port for VGA and HDMI display output
Resolution:
–VGA: Up to 1920 x 1200 at 60Hz
–LVDS: 24-bit LVDS, up to 1920 x 1200 at 60Hz
–HDMI: Up to 3840 x 2160 at 30Hz

3 MIO-2360 User Manual
Chapter 1 General Introduction
1.2.2 Functional Specifications
Processor
Chipset
Processor
Intel® Pentium N4200/Celeron M3350/Atom™ E3940/
Atom™ E3930
Frequency
–N4200/N3350 1.10 GHz
–E3930 1.60 GHz
–E3940 1.30 GHz
Manufacturing Technology: 14 nm
L2 cache: 2 MB
Memory Supports DDR3L 1866 MHz, up to 8 GB
SODIMM Socket: 204-pin SODIMM socket type *1
Graphic Engine
Directx* 11, OGL 3.0, OCL 1.1, OGL ES 2.0
Hardware decode/ acceleration:
–Encode: H264, MPEG2/4, VC1, WMV9
–Decode: H264, MPEG2
Display
VGA: 1920 x 1200 @ 60 Hz
HDMI: 3840 x 2160 @ 30Hz
LVDS1: 24-bit, up to 1920 x 1200 @ 60Hz, up to 1440 x 900
@ 60 Hz
Dual independent display: VGA+LVDS+MIOe or
HDMI+LVDS+MIOe
Control Hub Intel® SoC N3350/E3940/E3930
Audio
High Definition Audio (HD) ALC-888S codec
Up to 2 channel of PCM (Pulse Code Modulation) audio out-
put
Connectors: Line-out, Line-in
PCI-Express Interface
4 PCI-Express x1 Lanes
Lane 1 &2: MIOe connector
Lane 3: Full-size Mini PCIe connector
Lane 4: Intel i210 GbE controller
SATA Interface 1 x mSATA by mini-PCIe socket
1 x SATAIII (Max. Data transfer Rate 600 MB/s)
USB Interface
2 x internal USB ports
2 x rear I/O ports at coastline (two USB 3.0)
Transmission speed up to 480 Mbps (USB 2.0) / 5 Gbps
(USB 3.0)
Power Management
Full ACPI (Advanced Configuration and Power Interface) 3.0
Supports S0, S3, S4, S5
Support wake on LAN
BIOS AMI EFI 64 Mbit Flash BIOS via SPI

MIO-2360 User Manual 4
Others
1.2.3 Mechanical Specifications
1.2.3.1 Dimensions (mm)
L100 mm x W72 mm (3.9" x 2.8")
1.2.3.2 Height on top (mm)
15.7 mm (Heatsink)
1.2.3.3 Height under bottom (mm)
16.34 mm (Rear I/O USB)
1.2.3.4 Weight (g)
0.47 kg (1.04 lb, weight of total package)
1.2.4 Electrical Specifications
Power Supply Type: Single 12 V DC power input (support DC power hot plug)
1.2.4.1 Power supply Voltage
Single 12 V input 10%
Total peripheral power supply output: 5 V @ 3 A for CPU board and MIOe mod-
ule totally, 12 V @ 2 A for MIOe module
1.2.4.2 Power Consumption
Typical in Windows 10 Idle Mode:
N3350: 0.41 @ 12V (4.89 W)
E3940: TBD
E3930: TBD
Max in Windows 10 HCT12 (10 minutes):
N3350: 1.09 A @ 12 V (12.90 W)
E3940: TBD
E3930: TBD
Ethernet
Controller: Intel® i210 (GbE1)
Compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.3z, IEEE
802.ab
Support 10/100/1000 Mbps
Connectors: RJ45
LAN1 LED
–Link: Green (100Mbps)/ Orange (1000Mbps)
–Active: Green (flash)
Support wake on LAN
Serial ports
Controller: SMSC SCH 3114
2 x 232/422/485 serial ports with ESD protection: air gap ± 15
kV, contact ± 8 kV
GPIO
Controller: SMSC SCH 3114
8-Bit (programming) through Super I/O, pin header
5 V tolerance
SMBus Default is SMBus

5 MIO-2360 User Manual
Chapter 1 General Introduction
1.2.4.3 RTC Battery
Typical Voltage: 3.0 V
Normal discharge capacity: 210 mAh
1.2.5 Environmental Specifications
1.2.5.1 Operating Humidity
40 °C @ 95% RH Non-Condensing
1.2.5.2 Operating Temperature
0 ~ 60 °C (32~140 °F)
1.2.5.3 Storage Humidity
60 °C @ 95% RH Non-Condensing
1.2.5.4 Storage Temperature
-40 ~ 85 °C (-40 ~ 185 °F)
1.3 Function Block Diagram
DDR3L 1866
SO-DIMM up to 8GB
Intel Celeron
Intel Atom
SoC
N3350 / E3940
Full-size Mini-PCIe
SMBus/I
2
C*
Transmitter VGA
HDMI
Half-size mSATA
1 SATAIII
PCIe x1 DDI
Transmitter 18/24 bit
LVDS
eDP
2 USB2.0
Watchdog Timer
COM1: RS-232/422/485
COM2: RS-232/422/485
MIOe
DP/HDMI
SMBus
2 PCIe x1
Line-out
LPC
SATAII (optional)
2 USB3.0
RESET
USB2.0
SATAIII 600MB/s
USB2.0
SATAIII 600MB/s
2 USB3.0
USB3.0/USB2.0
AMI BIOS
SPI
Audio Codec
Line-in
Line-out
HD Audio
I2C
SMBus
Intel i210
8-bit GPIO SUPER I/O
RJ45
PCIex1
LPC
Single
Channel

MIO-2360 User Manual 6

Chapter 2
2H/W Installation
This chapter explains the setup
procedures of the MIO-2360 hard-
ware, including instructions on
setting jumpers and connecting
peripherals, as well as switches,
indicators and mechanical draw-
ings. Be sure to read all safety
precautions before you begin the
installation procedure.

MIO-2360 User Manual 8
2.1 Jumpers
2.1.1 Jumper Description
Cards can be configured by setting jumpers. A jumper is a metal bridge used to close
an electric circuit. It consists of two metal pins and a small metal clip (often protected
by a plastic cover) that slides over the pins to connect them. To close a jumper, you
connect the pins with the clip. To open a jumper, you remove the clip. Sometimes a
jumper will have three pins, labeled 1, 2 and 3. In this case you would connect either
pins 1 and 2, or 2 and 3.
The jumper settings are schematically depicted in this manual as follows.
A pair of needle-nose pliers may be helpful when working with jumpers. If you have
any doubts about the best hardware configuration for your application, contact your
local distributor or sales representative before you make any changes.Generally, you
simply need a standard cable to make most connections.
2.1.2 Jumper List
2.1.3 Jumper Settings
Warning! To avoid damaging the computer, always turn off the power supply
before setting jumpers.
Table 2.1: Jumper List
J1 LCD Power / Auto Power on
Table 2.2: J1: LCD Power/Auto Power on
Setting Function
(1-2) +5V
(3-4) (default) +3.3V
(5-6) (default) Auto Power On

9 MIO-2360 User Manual
Chapter 2 H/W Installation
2.2 Connectors
2.2.1 Connector List
2.2.2 Connector Settings
2.2.2.1 Battery Connector (BH1)
MIO-2360 supports Lithium 3 V/210 mAH CR2032 battery with wire via battery con-
nector (BH1).
2.2.2.2 12 V Power Input Connector (CN1)
Main power connector supports single 12 V input, and there's an optional choice of
DC/Jack (CN2, co-layout with 2pin power connector)
2.2.2.3 DDRIII SODIMM Socket (CN5)
One 204-pin/H9.2 mm DDRIII DIMM socket supports DDR3L 1866 MHz up to 8 GB.
CN1 12 V Power Input
CN2 DC JACK (by request)
CN3 12 V Power Input (2 x 3 pin support by request)
CN5 DDR3L SO-DIMM
CN7 GPIO
CN8 HD Audio
CN9 Gigabit Ethernet
CN10 Mini PCIe
CN11 SATA
CN12 mSATA
CN13 COM1/COM2
CN14 Inverter Power/Internal SATA Power
CN15 18/24 bits LVDS Panel
CN16 VGA
CN17 HDMI
CN18 MIOe
CN19 Internal USB 2.0
CN20 External USB 3.0
CN21 SMBus
CN22 Front Panel
CN26 Battery
Note! How to clear CMOS: (Must follow below steps)
1. Turn off system power
2. Unplug CR2032 battery cable on BH1
3. Waiting for 15sec or short BH1 pin1-2
4. Connect battery cable on BH1
5. Turn on system power