Advantech PCM-9370F Installation and operation manual

1 PCM-9372 Startup Manual


























PCM-9372 VIA Eden SBC with CPU, VGA/ LCD,
LVDS, Ethernet, and Audio
Startup Manual
Before you begin installing your card, please make sure
that the following materials have been shipped:
• 1 PCM-9372 all-in-one single board computer
• 1 startup manual
• CD-ROM or disks for utility, drivers, and manual (in PDF
format)
• 1 3.5" IDE flat cable 40-pin to 40-pin (patr no:
1701400452)
• 1 keyboard/ PS2 monse cable (part no. 1700060202)
• 1 second serial port cable (part no.1701140201)
• 1 parallel port cable (part no. 1700260250)
• 1 FDD cable for 3.5" FDD only (part no.1701340603)
• 1 Audio cable (part no. 1703100152)
• 1 USB cable (part no. 1703100121)
If any of these items are missing or damaged, contact
your distributor or sales representative immediately.
Note: For detailed contents of the PCM-9372,
please refer to the enclosed CD-ROM or disk
(in PDF format).
• CPU: Onboard Eden 667MHz MHz (PCM-9372F-M0A1)
or
VIA Eden 400 MHz processor (PCM-9372F-J0A1)
with 128KB L1 cache memory)
• BIOS: Award 256 KB Flash memory
• System memory: One 144-pin SODIMM socket
accepts 64 MB up to 512 MB SDRAM
• 2nd cache memory: 64 KB on the processor
• Enhanced IDE interface: One channels supports up to
two EIDE devices. BIOS auto-detect, PIO Mode 3 or
Mode 4, supports up to UDMA 66/100 mode
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/epc
Fortechnical support and service, please visit our support
website at:
http://support.advantech.com
This manual is for the PCM-9372 series Rev. A1.
Part No. 2006937200 1st Edition
Printed in Taiwan Sep., 2002
• FDD interface: Supports up to two FDDs
• Serial ports: Two serial RS-232 ports, COM1: RS-232,
COM2: RS-232/422/485
• Parallel port: One parallel port, supports SPP/EPP/
ECP mode
• Keyboard/mouse connector: Supports standard PC/
AT keyboard and a PS/2 mouse
• Power management: Supports power saving modes
including Normal/Standby/Suspend modes. APM 1.2
compliant
• Watchdog timer: 62 level timer intervals
• USB: Two USB 1.1 compliant universal serial bus ports
• Expansion: One PC/104 connector for ISA control
board
Solid State Disk
• Supports one 50-pin socket for CFC type I/II
VGA/LCD Interface
• Chipset: VIA Twister chip with integrated Savage4 2D/
3D/Video Accelerator
• Frame buffer: Supports 4/8/16/32MB frame buffer with
system memory
• Interface: 4X AGP VGA/LCD interface, Support for 9,
12, 15, 18, 24, 36 bit TFT and optional 16- or 24-bit
DSTN panel
• Display mode: CRT Modes: 1280 x 1024@16bpp
(60Hz), 1024 x 768@16bpp (85Hz); LCD/Simultaneous
Modes: 1280 x 1024@16bpp (60Hz), 1024 x
768@16bpp (60Hz)
• LVDS: Supports 2 Channel (2 x 18bit) LVDS interface
Ethernet interface
• Chipset: RTL 8100
• Ethernet interface: IEEE 802.3u 100BASE-T Fast
Ethernet compatible
• I/O address switchless setting
• Built-in boot ROM
Audio Function
• Chipset: VIA 82C686
• Audio controller: AC’97 ver. 2.0 compliant interface
• Audio interface: Microphone in, line in, line out
Packing List
Specifications
PCM-9372 VIA Eden SBC with CPU, VGA/LCD, LVDS, Ethernet, and Audio

2 PCM-9372 Startup Manual
Mechanical and Environmental
• Dimensions 145 x 102 mm (5.9"x 4.2")
• Power supply voltage: +5 V ±5% and +12V ±5%
• Power requirements:
Max
4.5A@+5V, 1.3A@+12V
(Within 5ms after power on)
typical
2.08A@5V,0.08A@+12V (W/ Eden-400,128MB)
2.33A@5V,0.08A@+12V (W/ Eden-667,128MB)
• Operating temperature: 0 ~ 60°C (32 ~ 140°F)
• Weight: 0.85 kg (weight of total package)
The board has a number of jumpers and connectors that
allow you to configure your system to suit your applica-
tion.
The tables below list the function of each jumper and con-
nector.
PCM-9372 Switches & Jumpers
* default setting
Jumpers and Connectors
Jumpers
Label Function
S1 System reset button
S2 CMOS clear button
S3 Panel type select
JP1 COM2 RS232/422/485 & WDT setting
Connectors
Label Function
CN1 LCD Inverter control connector
CN2 Flat panel connector
CN3 LVDS connector
CN4 Ext. flat panel connector
CN5 CRT display connector
CN6 PC/104 expansion
CN7 ATX feature connector
CN8 COM 1 port connector
CN9 Main Power connector
CN10 Peripheral power connector (-5V, -12V)
CN11 Power & HDD LED connector
CN12 Keyboard and PS/2 mouse connector
CN13 IDE hard drive connector (primary)
CN14 Audio connector
CN15 Ethernet connector
CN16 COM2 port connector
CN17 USB channel 1, 2 connector
CN18 ATX power on/off switch connector
CN19 Parallel port connector
CN20 Floppy drive connector
CN21 CFC connector
CN22 CPU fan power connector
S2 CMOS clear button
Condition Result
unpressed* Normal
pushed Clear CMOS
JP1 Watchdog timer action
Pins System reset* IRQ11
7-8 closed open
9-10 open closed
JP1 COM2 RS-232/422/485 select
Pins RS-232* RS-422 RS-485
1-2 Open Open Closed
3-4 Open Closed Open
5-6 Closed Open Open

PCM-9372 Startup Manual 3
PCM-9372 Connectors (component side) PCM-9372 Switches & Connectors (solder side)
S1 Panel Type select
SW SW SW SW
1-1 1-2 1-3 1-4 Panel type
ON ON ON ON DSTN** 640x480 18bit
ON ON ON OFF TFT 640x480 18bit
ON ON OFF ON TFT 640x480 LVDS
ON ON OFF OFF (Resvd)
ON OFF ON ON (Resvd)
ON OFF ON OFF DSTN** 800x600 18bit
ON OFF OFF ON TFT* 800x600 18bit
ON OFF OFF OFF TFT 800x600 LVDS
OFF ON ON ON (Resvd)
OFF ON ON OFF (Resvd)
OFF ON OFF ON DSTN** 1024x768 36bit
OFF ON OFF OFF TFT 1024x768 36bit
OFF OFF ON ON TFT 1024x768 1Chan LVDS
OFF OFF ON OFF TFT 1024x768 2Chan LVDS
OFF OFF OFF ON TFT 1024x768 18bit
OFF OFF OFF OFF TFT 1024x768 24bit
* Default setting
** will support in the future
CN1 CN22 CN11
CN19
CN13
CN6
CN8
CN
17
CN18
CN12
CN10
CN14
CN16
CN7 CN9
CN5 CN
CN 2
CN 3
CN 4
20
CN15

4 PCM-9372 Startup Manual
PCM-9372 Mechanical Drawing(component side)
PCM-9372 Mechanical Drawing (solder side)