Advantech PCM-4386 Installation and operation manual

PCM-4380 Startup Manual1
PCM-4380 Pentium ® M 4" SBC with MIO/VGA/
LVDS Ethernet/USB2.0
Startup Manual
Before you begin installing your card, please make sure
that the following materials have been shipped:
If any of these items are missing or damaged, contact your
distributor or sales representative immediately.
Note 1: For detailed contents of the PCM-4380, please
refer to the enclosed CD Disc or disk (in PDF for-
mat).
Note 2: Acrobat Reader is required to view any PDF file.
Acrobat Reader can be downloaded at:
http://www.adobe.com/products/acrobat/
readstep2.html (Acrobat is a trademark of Adobe.)
Standard SBC Functions
• CPU: Embedded Intel Pentium M/Celeron M
on board Pentium M 1.4 GHz (2M L2 cache)
PCM-4380F-S4A2E
on board Celeron M 1.0 GHz (1M L2 cache)
PCM-4380F-S0A2E
on board Celeron M 600 MHz (512K L2 cache)
PCM-4380F-M0A2E
• System Chipset: Intel 855GME GMCH/ICH4 Chipset
• BIOS: Award 512 Kbit Flash BIOS
• System Memory: 200 pin SODIMM socket, support
ECC Double Data Rate (DDR) 128 MB to 1 GB, accept
128M/256M/512M/1G, DDR 200/266/333 DRAM
• Power Management: APM1.2, ACPI support
• SDD: Supports CompactFlash Card Type I/II (shared
2nd IDE Channel) USB memory, uDOC (option)
• WatchDog Timer: Single chip watchdog 255-level timer
interval, setup by software
• Expansion Interface: Supports 8/16 bit ISA bus for
standard PC/104 device (ITE 8888g), PC/104-Plus
• Battery: 2 pin wafer box for external Battery on board
Enhance IDE Interface 1 x EIDE (UDMA 33), 1 x FDD,
UDMA 100 with PCM-063 riser card, 1 x Keyboard/
Mouse, 3 x RS232, 1 x RS-232/422/485, 1 x LPT
• USB: 4 x USB 2.0 compliant ports
• GPIO: 8-bit general purpose input/output
Solid State Disk
• Supports one 50-pin socket for CFC type I/II
VGA/LVDS Interface
• Chipset: Intel 855GME chip integrated (Extreme Graph-
ics 2)
• Memory Size: Optimized Shared Memory Architecture,
support up to 64MB frame buffer using system memory
• Resolution:
CRT Display Mode: pixel resolution up to 1600 x 1200
@85 Hz and 2048 x 1536 @75 Hz
LCD Display Mode: Dual channel LVDS panel sup-
ports up to UXGA panel resolution with frequency
range from 25 MHz to 112MHz with frequency range
from 25 MHz to 112 MHz
• LCD Interface: 2 Channel (2 x 18/36-bit) LVDS
• LVDS: Hirose connector support up to 2 channel (2 x 18-
bit) LVDS LCD Panel
• Dual Independent Display: CRT+ 36-bit LVDS
Ethernet interface
• Chipset supports:
10/100 Mbps - Intel 82551ER
10/100/1000 Mbps - Intel 82541PI (Optional)
• Ethernet interface: 2 x RJ45
• Standard: IEEE 802.3u 100Base-T
Packing List Specifications
• 1 PCM-4380 SBC
• 1 Startup manual
• 1 Utility CD
• Cable 20P/10P 10 cm EPIC
ATX Power (CN1) p/n: 1700002055
• Cable 2*4P/10P EPIC AT
POWER 15 cm (CN1) p/n: 1700003931
• Flat Cable 44P IDC 44P/44P/
40P Keyed 50 cm (CN27) p/n: 1701440504
• USB CABLE 20 Pin to 2 Port
L=30 cm (CN31) p/n: 1700004891
• Keyboard/Mouse Connector
(CN19) p/n: 1700060202
• Flat cable 44P 20 cm 3COM
& LPT 1.27 mm to D-sub
(CN30)
p/n: 1700002034
• CABLE USB*2/10-2.0 mm 29
cm p/n:1700001267
(PCM-4380U series
only)
For more information on this and other Advantech
products, please visit our website at:
http://www.advantech.com
http://www.advantech.com/eplatform
For technical support and service, please visit our
support website at:
http://www.advantech.com/support
This manual is for the PCM-4380 Series Rev. A2.
Part No. 2006438001 2nd Edition
Oct. 2007
PCM-4380 Pentium ® M 4" SBC with MIO/VGA/LVDS Ethernet/USB2.0

2 PCM-4380 Startup Manual
Audio Function
• Audio controller: Support AC97 3D surround stereo sound
• Audio interface: Speaker-out, CD-input, line-in, Line-out
Microphone (with PCM-410A-00A1E option)
Mechanical and Environmental
• Dimensions 115 x 165 mm (4.5"x 6.5")
Mechanical Drawing (dxf file) is available.
• Power Supply Type: ATX, AT
• Power Supply Voltage: +5 V ±5%, +12 V ±5%
ATX:
+5 V ±5%, ±12 V ±5% (Optional)
AT:
5 V only to boot up, 12 V for LCD inverter and PC/104
module (12 V optional for PC104 add on card and LCD
inverter)
• Operating Temperature: 0 ~ 60° C (32 ~ 140° F)
• Operating Humidity: 0% ~ 90% Relative Humidity, noncon-
densing
• Storage Temperature:
Standard products (0 ~ 60° C)
Storage temperature: -20 ~ 70° C
• Storage Humidity:
Standard products (0~60° C)
Relative humidity: 95% @ 60° C
• Weight: 0.85 kg (weight of total package)
• Optional Accessories:
PCM-410A-00A1E: AC 97 Audio/USB module for PCM-
4380/4386 series
PCM-410C-00A1E: COM/LPT daughter board for EPIC
The board has a number of jumpers that allow you to con-
figure your system to suit your application.
The table below lists the function of each of the jumpers
and connectors.
Note: In ATX mode, please use ATX power cable (PN:
1700002055: 20P/10P EPIC ATX POWER Cable 10CM)
in the bundle package to connect the power supply.
In AT mode, please use AT power cable (PN:
1700003931: 2*4P/10P EPIC AT POWER 15 cm) in the
bundle package to connect the power supply.
There are two 4 pin connectors on the AT power cable.
It's ok to connect single big 4P under AT mode.
The maximum current for (5 V, 12 V) through this “single
big 4P”.
Specifications
Jumpers and Connectors
Jumpers
Label Function
J1 AT/ATX power select
J2 LCD power
J3 COM2 setting
J4 PCI VIO setting
Connectors
Label Function
CN1 Power Con.
CN3 DDR-SODIMM (RVS)-5.2mm
CN4 Battery Con.
CN5 System Fan
CN6 Power Switch (PS: only work with ATX power)
CN7 GPIO
CN8 LAN1 (RJ45)
CN9 LAN2 (RJ45)
CN11 Compact II W/O Ejector
CN13 HD & Power LED
CN14 LVDS Connector
Jumpers and Connectors
Connectors
Label Function
CN15 Inverter Power
CN16 VGA connector
CN18 USB 0/1
CN19 KB_MS
CN21 COM1
CN24 ISA_-5V
CN26 RS-422/485
CN27 IDE0
CN28 MIO-USB (USB-DOC)
CN30 COM 2/3/4 & LPT
CN31 USB 2/3 & AC 97 (Audio I/F)
J1: ATX/AT Power Select
Setting Function
1-2 AT Power mode
None ATX Power mode
J2: LCD Power
Pin Signal
1-2 +5 V
2-3 +3.3 V
J3: COM2 Setting
Pin Signal
1-2 RS232
3-4 RS485
5-6 RS422
J4: PCI VIO Setting
Pin Signal
1-2 +5 V
2-3 +3.3 V
123
123
123
123

PCM-4380 Startup Manual 3
PCM-4380 Connectors (component side)
PCM-4380 Connectors (solder side)

4 PCM-4380 Startup Manual
PCM-4380 Mechanical Drawing (component side)
PCM-4380 Mechanical Drawing (solder side)