AECO SMC-12 NO SS BC HF AGD1 Series User manual

www.aecosensors.com
YSM NNNNNN
SMC-12 NO SS BC HF LC2 AGD1
YSM000026 SMC-12 NO SS BC HF LC5 AGD1
YSM000027 SMC-12 NO SS BC HF LC10 AGD1
YSM000028
FM011EX Rev. B
SMC-12 NO AGD
LC10
1
SS
LC5
ETC000468
BC HF
LC2
SMC-12 NO SS BC HF ■AGD1
mm
%Sn
V
A
W/VA
Hz
°C
IP
<10
NO
230
0.5
50
230
-25 ÷ +70
67
50
M12x1
CH.17
Ø 24
4
= = 15
NO
4. Electrical and Mechanical Characteristics
( Description )( Code )
3.3 Product series
The magnetic sensors series includes the
models listed below : SMC-12 NO SS BC HF ■AGD1
Potentially explosive atmosphere
with GAS and/or DUST.
Cable length "2mt".
Cable length "5mt".
Cable length "10mt".
Equipment category "1"
according to 2014/34/EU Directive.
Magnetic Sensor with cylindrical enclosure
"M12x1" and "NORMALLY OPEN" output
3.2 Description diagram
3.1 Code diagram
Magnetic sensor intended for use in the explosive atmospheres
according to 2014/34/EU ATEX Directive and IECEx Certification
system.
Progressive number
3. Sensor identification
The series is only identified by the
''Code'' and ''Description''. The diagrams for the decoding are shown below.
SMC-12 NO SS BC HF ■AGD1
1. Introduction
This manual should be read and understood in all its parts before proceeding
with installation of the sensor.
The Magnetic Sensors series, are intended to
be used in a potentially explosive atmospheres with presence of GAS and/or
DUST. They are designed and produced according to the requirements of the
following standards:
SMC-12 NO SS BC HF ■AGD1
2. Installation and Startup
The sensor must be installed, connected and activated only by specialized
personnel. Personnel must be familiar with the types of protection anti-ignition,
the production rules and regulations in the potentially explosive area. The user
is solely responsible for the choice and the use of sensor suitable to the final
application. When installing the sensor observe the following requirements:
Check whether the classification of the sensor is suitable for the application
(see‘’ATEX Marking’’to paragraph 5 and marking on the equipment).
Make sure that the connection cable of the sensor does not have the
endings too tight. Moreover it must not prevent the movement of people
and/or things.
Do not touch uninsulated parts of the connecting cable of the sensor before
having it disconnected from the supply voltage. Do not install the sensor
during a thunderstorm with lightning.
If the cable is subject to movement, do not place the sheath with bending
radius too short; Pay attention to the mounting of the parties subject to
movement and to the fixed ones.
Separate the power cables from the connecting cable of the sensor.
Make sure that the sensor housing is always ground wired.
Operating Instructions
GB
According to:
Annex II P1.0.6 group II, equipment category 1G/1D
Directive 2014/34/EU ( ATEX )
IECEx Certification system
issued by Notification Body IMQ spa.
•EU Type Examination Certificate n° IMQ 12 ATEX 016 X (for ATEX Directive)
•Certificate of Conformity (CoC) n° IECEx IMQ 16.0014X (for IECEx system)
All sensors of this series are covered by the following certificate:
•EN 60079-0:2012+A11:2013 e EN 60079-18:2015 (for ATEX Directive)
• IEC 60079-0:2011 e IEC 60079-18:2014 (for IECEx system)
Protect the sensor cable according to EN 60079-14 (for ATEX) and
IEC60079-14(for IECEx) standards.
The electrical and mechanical characteristics of this series are shown in Table 1:
Tab. 1 - Electrical and Mechanical Characteristics
Housing material: Stainless steel-AISI316
Cable material: PUR/TPE shielded-Halogen free
RED
BLACK
SHIELD
> 20 with M20 magnet
Stainless steel-AISI 316
2 x 24 AWG PUR/TPE HF shielded
2mt, 5mt or 10mt
Sensing distance (Sn)
Hysteresis (’’H’’)
Max switching voltage
Ambient temperature range
IP rating
Housing material
Cable
Output type
Max switching current
Max switching power
Max switching frequency
Characteristics Models
WIRING DIAGRAM
Dimensions ‘’mm’’

SMC-12 NO SS BC HF ■AGD1
V= 230V I= 0.5A P= 50W/VA
Tamb: -25 ÷ +70°C
IMQ 12 ATEX 016X
0722
II 1G Ex ma IIC T6 Ga
II 1D Ex ma IIIC T85°C Da
AECO Inzago-MI-Italy Fig. 2
IECEx IMQ 16.0014X
2016 12345
IP67
Fig. 1
NO
Fp Fp
BLACK
RED
9. EU Declaration of Conformity (ATEX)
7. Maintenance
The sensor has no serviceable components and can not be changed and / or
repaired. In case of failure, please contact AECO srl customer service.
If necessary, you can ask AECO srl for a copy of the following documents :
You can also download the same documents from AECO web site
( ).www.aecosensors.com
Production batch
ATEX/IECEx marking
EC-Type Examination
Certificate number
Ambient temperature range
‘’Model’’ description
Electrical parameters
Wiring diagram
8. Labelling
On every sensor of the '' '' is
applied as shown in Fig. 2 :
SMC-12 NO SS BC HF ■AGD1 series a label
RED
BLACK
Signal
Signal
Sensor Control
If the non resettable fuse complies with IEC 60127 series or
IEC 60691 or ANSI/UL 248-1 only one fuse is necessary.
Protection Fuse
Fp =
Inf (A)= 0.8A
(Fuse nominal current) Vnf (V)=230Vac
(Fuse nominal voltage) Rupture capacity
1500A
Temperature class for GAS
Indicates the maximum surface temperature that can reach the sensor
at the maximum ambient temperature according to EN 60079-0 (for
ATEX) e IEC 60079-0 (for IECEx).
T6 Maximum surface temperature : 85 °C
Maximum Surface Temperature for DUST
Indicates the maximum surface temperature that can reach the sensor
at the maximum ambient temperature according to EN60079-0(for A
TEX) e IEC60079-0(per IECEx)
T85 Maximum surface temperature : 85 ° C
Equipment Protection Level (EPL) for GAS
Indicates the level of protection of the equipment according to
EN 60079-18(for ATEX) and IEC 60079-18(for IECEx).
Ga Equipment with protection level 'ma'
Equipment Protection Level (EPL) for DUST
Indicates the level of protection of the equipment according to
EN 60079-18(for ATEX) and IEC 60079-18(for IECEx)
Da Equipment with protection level 'ma'
6. Conditions of use in potentially explosive area.
During the use of the sensor in potentially explosive atmosphere observing
the following instructions is important for safety :
The maximum permissible ambient temperature is Ta = +70 °C
To protect the sensor from damage due to shock and vibration
It is necessary to protect the circuit by connecting in series to the sensor
n° 2 non resettable fast-acting fuses with the following ratings :
5. ATEX and IECEx marking
ZONE 0, ZONE 1 and ZONE 2 (Atmosphere with GAS)
ZONE 20, ZONE 21 and ZONE 22 ( DUST)Atmosphere with
for use in
For all models '' '' refere to the ATEX and
IECEx marking below indicated :
SMC-12 NO SS BC HF ■AGD1
The meaning of the symbols that make the marking is as follows:
Specific mark. Protection against explosion
II Equipment group .
(Atex only)
Category group .(Atex only)
1Equipment designed for use in places where
(ZONE 0 or ZONE 20).an explosive atmosphere is constantly present
Equipment suitable for use in all other places other than mines and
their surface installations.
GAtmosphere due to the presence of gases, vapors and mists.
DAtmosphere due to the presence of dust
Ex Equipment designed for use in potentially explosive atmospheres
Type of explosive atmosphere(Atex only).
ma Type of protection
Encapsulation protection level according to EN 60079-18(for
ATEX) and IEC 60079-18(for IECEx).
''ma''
Explosion group GAS
Specifies the explosion group which the type of GAS belongs to,
according to .EN 60079-20(for ATEX) and IEC 60079-20(for IECEx)
IIC An typical GAS of this group is the hydrogen
Explosion group DUST
IIIC Conductive dust
Specifies the explosion group which the type of DUST belongs to,
according to EN 60079-0 (for ATEX) e IEC 60079-0 (for IECEx).
II 1D Ex ma IIIC T85°C Da
II 1G Ex ma IIC T6 Ga Ex ma IIIC T85°C Da
Ex ma IIC T6 Ga
(ATEX marking) (IECEx marking)
Sensor data sheet
EU Declaration of Conformity (for ATEX only)
EU Type Examination Certificate (for ATEX only)
IECEx Manufacturer Declaration (for IECEx only)
Certificate of Conformity (CoC) (for IECEx only)
IP protection grade
Manufacture year
Certificate of Conformity(CoC) number
10. Manufacturer Declaration ( IECEx)
Manufacturer Declaration
Product’s name: Magnetic Sensors
Models: SMC-12 NO SS BC HF ■AGD1
IECEx Marking:
Ex ma IIC T6 Ga
Ex IIIC T85°C Dama
Certificate of Conformity(CoC):
Notified body of the
Certificate of Conformity(CoC):
IECEx IMQ 16.0014X
Inzago: 2016.09.01 Maurizio Scaramuzza
We AECO s.r.l.
Via G. Leopardi 5, 20065 Inzago (MI), Italy
CESI spa
Via R. Rubattino n° 54
20134 Milano, Italy
n° 0722
IMQ spa
Via F. Quintiliano n° 43
20138 Milano, Italy
n° 0051
CMD007EX REV. A
-25°C< Ta <+70°C
IEC 60079-0:2011
IEC 60079-18:2014
IEC 60947-1 : 2007
IEC 60947-5-1 : 2003
according to IECEx certification system
declare under our sole responsibility that the products:
Monitoring body for Quality
Assessment Report (QAR):
to which this declaration relates are in conformity with the following standards:
Legal representative
declare under our sole responsibility that the products:
EU Declaration of Conformity
Product name: Magnetic Sensors
Models: SMC-12 NO SS BC HF ■AGD1
ATEX Marking:
II 1G Ex ma IIC T6 Ga
II 1D Ex IIIC T85°C Dama
EU Type Examination:
Notified body of the
EU-Type examination:
IMQ 12 ATEX 016 X
Inzago: 2016.09.01 Maurizio Scaramuzza
We AECO s.r.l.
Via G. Leopardi 5, 20065 Inzago (MI), Italy
2014/34/EU -
ATEX Directive
2014/35/EU -
Low voltage Directive
Legal representative
CESI spa
Via R. Rubattino n° 54
20134 Milano, Italy
n° 0722
Monitoring body per appendix IV
of the directive 20014/34/EU:
IMQ spa
Via F. Quintiliano n° 43
20138 Milano, Italy
n° 0051
CUE055EX REV. A
-25°C< Ta <+70°C
EN60079-0:2012 + A11:2013
EN60079-18:2015
EN 60947-1 : 2007
EN 60947-5-1 : 2004
and are comply with the following armonized standards
to which this declaration relates, meet the requirements of the european directives
(■= LC5 orLC10)
LC2 or
(■= LC5 orLC10)
LC2 or
Shield