AEG ALT58BC401 User manual

ALT58BC401
ALT58BC
A58BCT18

2
2
Important!
It is essential that you read the instructions in this manual before
assembling, operating, and maintaining the product.
Subject to technical modifications.
ALT58BC
ALT58BC401
A58BCT18
x3

33
ALT58BC
ALT58BC401
A58BCT18
x3
THROTTLE LOCK
THROTTLE TRIGGER
HARNESS HANGER
UPPER SHAFT
BLADE GUARD
BIKE HANDLE
LOWER SHAFT
KNOB
BLADE
LINE TRIMMER GUARD
LINE TRIMMER HEAD
HARNESS
CONSTRUCTION WASHER
BLADE NUT
OPERATOR’S MANUAL
COMBINATION WRENCH
BATTERY PACK
LOCK PIN
TORX KEY
CHARGER

4
4
14
18
11 13
CHANGING FROM BRUSHCUTTER HEAD TO LINE TRIMMER HEAD
INSTALLING THE BLADE INSTALLING THE LINE TRIMMER HEAD
CHANGING FROM LINE TRIMMER HEAD TO BRUSHCUTTER HEAD

55
23 8
910
INSTALLING THE BLADE GUARD INSTALLING THE LINE TRIMMER GUARD
ATTACHING AND REMOVING THE HARNESS INSTALLING THE BIKE HANDLE

6
6
23
22
32 34
REMOVING THE LOWER SHAFT
ATTACHING THE LOWER SHAFT
CLEANING THE PRODUCTRELOADING THE TRIMMING LINE

77
26 24
27 29
35
STARTING THE PRODUCT INSERTING AND REMOVING THE BATTERY PACK
STORING THE PRODUCT
OPERATING THE LINE TRIMMEROPERATING THE BRUSHCUTTER

8
8
2
1
2
1
INSTALLING THE BIKE HANDLE
INSTALLING THE BLADE GUARD

99
2
1
2
1
INSTALLING THE BLADE GUARD

10
10
3
4
2
1
1
1
2
3
4
2
1
1
2
1
2
3
2
INSTALLING THE LINE TRIMMER GUARD
INSTALLING THE BLADE

11 11
3
4
2
1
NOTE: When installing the blade head,
always use a new nylon locking nut. Not
using a new nylon locking nut can result
in damage to the product or injury to
the user.
1
1
2
3
4
2
1
1
2
1
2
3
2
INSTALLING THE BLADE

12
12
6
5
1
2
3
4
2
1
NOTE: Make sure that the nylon locking
nut torque is ≥ 25 Nm when assembling
the blade. Failure to follow this
procedure can result in serious injury.
Nylon locking nut should have at least 4
turns after finger tight.

13 13
6
5
1
2
3
4
2
1
INSTALLING THE LINE TRIMMER HEAD

14
14
1
2
3
4
2
1
1
2
7
8
6
5
1
2
12
1
2
3
CHANGING FROM LINE TRIMMER HEAD TO
BRUSHCUTTER HEAD

15 15
1
2
3
4
2
1
1
2
7
8
6
5
1
2
12
1
2
3

16
16
10
9
11
12
14
1
2
13
NOTE: When installing the blade head,
always use a new nylon locking nut.
Not using a new nylon locking nut can
result in damage to the product or
injury to the user.

17 17
10
9
11
12
14
1
2
13
NOTE: Make sure that the nylon locking
nut torque is ≥ 25 Nm when assembling
the blade. Failure to follow this
procedure can result in serious injury.
Nylon locking nut should have at least 4
turns after finger tight.

18
18
3
4
2
1
2
3
1
2
7
8
6
5
1
CHANGING FROM BRUSHCUTTER HEAD TO
LINE TRIMMER HEAD

19 19
3
4
2
1
2
3
1
2
7
8
6
5
1

20
20
1
1
2
10
9
12
11
2
1
2
14
13