AEG CHDE 6260 User manual

DE 6250
DE 6260
CHDE 6260
335 D
Dunstabzugshaube
Afzuigkap
Hotte
Cooker Hood
Montage- und Gebrauchsanweisung
Installatie- en gebruiksaanwijzing
Notice d’utilisation et d’installation
Operating and Installation Instructions

37
Contents
Safety warnings 38
Fortheuser 38
Fortheinstaller 38
Description of the Appliance 40
Extractorversion 40
RecirculationVersion 40
Hood Operation 41
Maintenance and care 41
Metalgreasefilter 42
Openthemetalgreasefilter 42
Charcoalfilter 43
Changingthelightbulb 44
What to do if 45
Service and spare parts 46
Technical Details 47
Electrical connection 47
Printedonrecycledpaper
AEG - putting words into action

38
Safety warnings
For the user
•Thecookerhoodisdesignedtoextractunpleasantodoursfromthe
kitchen, it will not extract steam.
•Alwayscoverlightedelements,topreventexcessheatfrom
damaging the appliance. In the case of oil, gas and coal fired
cookers it is essential to avoid open flames.
•Also, when frying, keep the deep frying pan on the cooker top/cooker
undercarefulcontrol.
•Thehotoilinthefryingpanmightigniteduetooverheating.
•The risk of self-ignition increases when the oil being used is dirty.
•It is extremely important to note that overheating can cause a fire.
•Never carry out any flambécooking under the hood.
•Always disconnect the unit from the power supply before
carrying out any work on the hood, including replacing the
light bulb (take the cartridge fuse out of the fuse holder or switch off
theautomatic circuit breaker).
•It is very important to clean the hood and replace the filter at
the recommended intervals. Failure to do so could cause
grease deposits to build up, resulting in a fire hazard.
For the installer
•When used as an extractor unit, the hood must be fitted with a
120mmdiameterhose.
•When installing the hood, make sure you respect the following
minimum distance from the top edge of the cooking hob/ring
surfaces:
electric cookers 600 mm
gascookers 650 mm
coal and oil cookers 700 mm min.
•Thenationalstandardonfuel-burningsystemsspecifiesamaximum
depression of 0.04 bar in such rooms.
•The air outlet must not be connected to chimney flues or combustion
gas ducts. The air outlet must under no circumstances be connected
toventilationductsforroomsinwhichfuel-burning appliances are
installed.
•The air outlet installation must comply with the regulations laid down
bythe relevant authorities.
•When the unit is used in its extractor version, a sufficiently large
ventilationhole must be provided, withdimensionsthatare
approximately the same as the outlet hole.

39
•Nationaland regionalbuildingregulations impose anumberof
restrictionson using hoods and fuel-burning appliancesconnectedto
a chimney, such as coal or oil room-heaters and gas fires, in the
sameroom.
•Hoods can only be used safely with appliances connected to a
chimneyif the room and/orflat(air/environment combination) is
ventilatedfrom outside usingasuitable ventilation hole approximately
500-600cm2 largeto avoid the possibility of a depression being
createdduring operationofthe hood.
•Ifyou have any doubts, contact the relevant controlling authority or
buildinginspector’s office.
•Since the rule for rooms with fuel burning appliances is “outlet hole of
the same size as the ventilation hole”, a hole of 500-600 cm2, which
is to say a larger hole, could reduce the performance of the extractor
hood.
•If the hood is used in its filtering function, it will operate simply and
safelyin the above conditions without the need foranyof the
aforementionedmeasures.
•When the hood is used in its extractor function, the following rules
mustbe followed to obtain optimal operation:
—short and straight outlet hose
—keep bends in outlet hose to a minimum
—never install the hoses with an acute angle, they must
always follow a gentle curve only
—keep the hose as large as possible (preferably the same diameter
as the outlet hole).
•Failure to observe these basic instructions will drastically reduce the
performanceand increase the noise levelsoftheextractor hood.

40
Description of the Appliance
•Thecookerhoodisdesignedtoextractunpleasantodoursfromthe
kitchen, it will not extract steam.
•The hood is supplied as an extractor unit and can also be used in a
recirculationmode by fitting one charcoalfilter(availablefrom your
localService ForceCentre).
Extractor version
•In this version fumes are extracted to the outside via a hose.
•Inorder to obtain the best performance the hose shouldhavea
diameter equal to the outlet hole.
Recirculation Version
•Theair is filtered through a charcoal filter and returned to thekitchen.
•Youwill need an original AEG charcoal filter forthe recirculation
function.(Available fromyourlocal ServiceForceCentre).
•Insert the charcoal filter into the lugs of the frame above using the 2
red lugs Eto retain it, press the red lugs inwards, and insert the
charcoal filter in the frame. Fig. 1.
EE
E
Fig. 1

41
Hood Operation
•Best results are obtained by using a low speed for normal conditions
andhigh speed whenodoursare more concentrated.Turnthe hood
on a few minutes before you start cooking then you will get an
underpressureinthe kitchen. It should be left on aftercookingfor
about15 minutes or until allodourshavedisappeared.
The control switches are located on the unit’s front panel:
Thehoodis also equipped with a micro-switch which can be found
underthe lower runner of the visor on the right hand side.
With this micro-switch, the appliance may be automatically switched
on and off by opening and closing the pull-out panel, but only if the fan
speed has already been set and the light button is turned to “I”.
Maintenance and care
•The hood must always be disconnected from the electricity
supply before beginning any maintenance work.
•Neverinsert pointed objects in the motor’s protective grid.
•Washtheoutsidesurfaces using a delicate detergent solution. Never
usecaustic detergents or abrasive brushes orpowders.
•Only ever clean the switch panel and filter grille using a damp cloth
anddelicate detergents.
•It is extremely important to clean the unit and change the filters at
therecommendedintervals. Failure to do so will cause grease
deposits to build up that could constitute a fire hazard.
ON
OFF
Intensivespeed
Light switch Motor switch

42
Metal grease filter
•Thepurpose of the grease filters isto aspirate grease particles which
form during cooking and it must always be used, either in the
externalevacuation or internalrecyclingfunction.
Attention:themetalgreasefiltersmustberemovedandwashed,
eitherby hand or in the dishwasher,every four weeks.
Open the metal grease filter
•Model CHDE 6260:Toremove the grease filters, firstpullthehandles
upwards, then extract the filter outwards. Fig. 2a.
•Model 335 D:Toremove the grease filters, first removethegrid(see
Fig. 2a) and take out the grease filters oushing on the locking
springs Z. Fig. 2b.
Hand washing
Soakgreasefiltersforaboutonehour in hot water with a grease-
looseningcleaner,then rinse offthoroughlywithhot water.Repeat
the process if necessary. Refit the grease filters when they are dry.
Dishwasher
Placegreasefiltersinthedishwasher.Select most powerful washing
programmeand highest temperature, at least65°C.Repeatthe
process. Refit the grease filters when they are dry.
When washing the metal grease filter in the dishwasher a slight
discolouration of the filter can occur, this does not have any impact
onits performance.
•Cleanthe inner housing using ahotdetergentsolution only (never
usecaustic detergents, abrasive powdersorbrushes).
Fig. 2a Fig. 2b
Z

43
Charcoal filter
•The charcoal filter should only be used if you want to use the hood in
therecirculation function.
•Todo this you will need an original AEG charcoal filter (available from
yourlocal Service ForceCentre).
•Thecharcoal filtercannotbe washednorregenerated.
Thecharcoal filter shouldbereplaced every 12monthsunder normal
use.
Replacementfilters areavailablefrom your localServiceForce
Centre.
Fitting the charcoal filter:
Insert the charcoal filter into the lugs of the frame above using the 2
red lugs Eto retain it, press the red lugs inwards, and insert the
charcoal filter in the frame. Fig. 3.
•Removing:
Press both red lugs E upwards (towards the inside of the housing)
andremove the charcoal filterdownwards.Bild. 3.
•Alwaysspecifythehood model code number and serial number
whenordering replacement filters. Thisinformationisshown on the
registration plate located on the inside of the unit.
•Thecharcoal filter can beorderedfromyour local Service Force
Centre.
EE
E
Fig. 3

44
Warning
•Failuretoobserve the instructions on cleaning the unit and changing
thefilters will cause a fire hazard. You are therefore strongly
recommendedto follow these instructions.
•Themanufacturer declines all responsibility for any damage to the
motoror any fire damagelinkedtoinappropriate maintenance or
failuretoobservethe abovesafetyrecommendations.
Changing the light bulb
•Disconnect the cooker hood from the main supply.
•Removethe grease filter/s or the grid(model335D).
•Replace the old bulb with a new one of the same type.
•Refit the grease filter/s or the grid.
•If the light does not come on, make sure the bulb has been inserted
correctlybefore contacting your local Service Force Centre.

45
What to do if
Ifyourappliance fails to work properly please carry out the following
checks.
Symptom Solution
The cooker hood will not start... Check that:
Thehoodisconnected to
the electricity supply.
Check that a fan speed has
beenselected
The cooker hood is not working Check that:
effectively.. The fan speed is set high
enoughforthetask.
Thegrease filters are clean.
Thekitchen is adequately vented
to allow the entry of fresh air.
If set up for recirculation, check
that the charcoal filter is still
effective.
If set up for extraction, check that
the ducting and outlets are not
blocked.
Thecooker hood has Thesafetycut-out device hasbeen
switchedoff duringoperation... tripped.
Turnoff the hobandthenwait for
thedevice to reset.
Ifthe hood has been installed
below the heights indicated in the
installation instructions the motor
willcut-out frequently which will
damagethehood.
If after all these checks, the problem persists, contact your local
ServiceForce Centre, quotingthemodeland serial number.
Pleasenotethat it will be necessary to provide proof of purchasefor
anyin-guarantee servicecalls.
In-guaranteecustomers shouldensurethat the abovecheckshave
been made as the engineer will make a charge if the fault is not a
mechanicalor electrical breakdown.

46
Service and spare parts
Inthe event of your appliance requiring service, or if you wish to
purchase spare parts, contact your local AEG Service Force Centre by
telephoning
08705 929 929
Your call will be automatically routed to the Service Centrecovering
your post code area.
Forthe address ofyourlocalService Force Centreandfurther informa-
tion about Service Force, please visit the website at
www.serviceforce.co.uk
Please ensure that you have read the section „What to do if....“as the
engineer will make a charge if the fault is not a mechanical or electrical
breakdowneventheappliance isunderwarranty.
Please note that proof of purchase is required for in-guarantee
service calls.
Help us to help you
Pleasedetermine your type ofenquirybefore writing or telephoning.
When you contact us we need to know:
•Yourname
•Address and post code
•Telephonenumber
•Clear and concise details of the fault
•Nameand model oftheappliance*
•Enumber*
* This information can be found on the rating plate, which can be seen
whenthegreasefilters areremoved.

47
Technical Details
Model: CHDE 6260 335D
DE 6260
DE 6250
Maximum absorbed power: 330 W 230 W
Fuse rating: T6A250V T6A250V
Motorabsorption: 2 x 125 W 1 x 150 W
Lighting: 2 x 40 W 2 x 40 W
Duct diameter Ø120 mm Ø120 mm
Length of the cable: 150 cm 150 cm
Electrical connection
Safety warnings for the electrician
The electric outlet should be placed on the wall inside the chimney. The
hood has a power cable, 150 cm, with earth connection and the rated
voltageis 220 - 240 V (CHDE 6260/335D) - 230V (DE 6260 - DE 6250).
Connect the hood to the mains supply via a double pole switch
which has 3 mm minimum separation between the contacts.
The switch must be accessible at all times.
Thefollowing is valid in the United Kingdom only:
- the wire which is coloured green and yellow must be connected to
the terminal which is marked with the letter E or by the earth symbol
( ),orcoloured green or green and yellow;
- the wire which is coloured blue must be connected to the terminal
which is marked with the letter N or coloured black, -
- the wire which is coloured brown must be connected to the terminal
which is marked with the letter L or coloured red.

340
270
135
120
650 min
560
566
600
400 min
340
135
120
650 min
400
599
270
420 min.
600
130
560 min
130
D
B
C
2 3
A
B
D
C
1
2
3
C:4
C:4.1
C:4.2
D:4
5
6
7
8
9
10
11-3.1 11-3.2
DE 6250-ml
DE 6260-ml
A
10 x 4,5x13 mm (DE 6260)
8 x 4,5x13 mm (DE 6250)
6 x 4,5x16 mm
4 x 5,0x45 mm (DE 6260)
2 x 5,0x45 mm (DE 5260)
2 x
(DE 6260)
3 x 2,9x13 mm
2 x
4 x 8 mm (DE 6260)
2 x 8 mm (DE 5260)
LI1R6A
AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
© Copyright by AEG

19 mm
DE 6250
Ø 120 mm
2,9 x 13 mm
600
528
35
510
348
¯ 8 mm
=
=
b
a
2
3
153 153
D:4
C:4
8
11
1
3 x 4,5x16
2 x 4,5x13
(430 D - 450 D)
4 x 4,5x13
(330 D - 350 D )
5
4
C: 4.2 C:4.1
6
7
54 - 100 mm
10
9
3.2
6 x 4,5x13
ab
017 - (C)
16 33
19 36}(D)
4 6
5 7
100/120 mm Ø
3.1
120 mm Ø 120 mm Ø
330/350 D
16 - 20 mm
430/450 D
3.2
Ø120 mm
2,9 x 13 mm
3.1

AEG Hausgeräte GmbH
Postfach 1036
D-90327 Nürnberg
http://www.aeg.hausgeraete.de
http://www.aeg.co.uk
© Copyright by AEG LI1R7B Ed. 07/02