AEM LSC22 User manual

CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
INSTALLATION AND OPERATION MANUAL
REV 1.00 January 24, 2017
Anodyne Electronics Manufacturing Corp.
15-1925 Kirschner Road
Kelowna, BC, Canada.
V1Y 4N7
Telephone [phone]
Facsimile [phone]
Website: www.aem-corp.com
© 2017 Anodyne Electronics Manufacturing Corp. (AEM),
All Rights Reserved
ASM-LSC22
LSC22
Loudspeaker Controller

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
Installation and Operation Manual Page ii
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
COPYRIGHT STATEMENT
© 2017 Anodyne Electronics Manufacturing Corp. (AEM), All Rights Reserved
This publication is the property of AEM and is protected by Canadian copyright laws.
No part of this document may be reproduced or transmitted in any form or by any means
including electronic, mechanical, photocopying, recording, or otherwise, without the prior
written permission of AEM.

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
Installation and Operation Manual Page iii
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Prepared By:
Checked By:
Approved By:
The status of this installation and operation manual is controlled by the revision shown on the title page.
The status of each section is controlled by revision shown in the footer of each page. All revisions affecting
sections of this manual have been incorporated.
AEM MANUAL REVISIONS
Section
Revision Number
Revision Description
Date
All
Rev: 1.00
Initial release
Jan 24, 2017
Tony Pearson
Designer
Jan 24, 2017
Steve Kempf
Designer
Feb 1/17
Tom Betzelt
Product Support Manager
Feb 1, 2017
Todd Blackstock
R&D Manager
Feb 2/17

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
Installation and Operation Manual Page iv
ENG-FORM: 820-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Table of Contents
Section Title Page
1.0 Description
1.1 Introduction 1-1
1.2 Product Description 1-1
1.3 Design Features 1-1
1.4 Specifications 1-2
1.4.1 Electrical Specifications 1-2
1.4.2 Physical Specifications 1-5
1.4.3 Environmental Specifications 1-5
1.4.4 Product Approval/Certification 1-6
1.5 Unit Nomenclature 1-6
2.0 Installation
2.1 Introduction 2-1
2.2 Unpacking and Inspection 2-1
2.2.1 Warranty 2-1
2.3 Installation Procedures 2-1
2.3.1 Warnings 2-1
2.3.2 Cautions 2-1
2.3.3 Cabling and Wiring 2-2
2.3.4 Post-Installation Checks 2-2
2.4 Adjustments and Connections 2-3
2.5 Accessories Required But Not Supplied 2-3
2.6 Continued Airworthiness 2-4
2.7 Installation Drawings 2-4
3.0 Operation
3.1 Introduction 3-1
3.2 General 3-1
3.3 Controls and Indicators 3-1
3.3.1 Message Selection/Function 3-1
3.3.2 AUX Input 3-3
3.3.3 Input Selection 3-3
3.3.4 Output Selection 3-3
3.3.5 Siren Selection 3-4
3.3.6 System On/Off & Volume 3-4
3.4 Sidetone 3-4
3.5 -3bB Select 3-4

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 1-1
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Section 1.0 Description
1.1 Introduction
Information in this section consists of product description, design features and specifications for the LSC22
Loudspeaker Controller. All derivative product information will be contained in the applicable manual
supplement, which may be obtained from AEM as required.
Review all notes, warnings and cautions.
1.2 Product Description
The LSC22 Loudspeaker Controller is designed to provide centralized control for an aircraft’s internal and
external loudspeaker systems.
The design is contained in one panel mounted unit, with an illuminated faceplate.
All audio and key lines are interfaced to existing aircraft audio systems.
Front panel switches provide selection of the various operational modes of the LSC22 and a
potentiometer provides output volume control.
Onboard flash memory provides a means to record messages for playback at a later time. A front panel
connector provides programming/recording access.
1.3 Design Features
The LSC22 provides selection and control of internal or external PA system(s) installed in an aircraft. An
integrated 25W speaker driver circuit is designed to drive one 8 Ohm speaker arrangement for internal
paging. The LSC22 also provides one low level audio signal external output that can drive the input on a
remote mounted power amplifier.
The LSC22 generates wail and yelp siren audio for use with a remote power amplifier and speaker
system.
A ‘-3dB’ function allows the output level of the system to be reduced by 3 dB when the input control line is
grounded. Removing the ground returns the system to full output. This function is used to create an “auto
level control’ that automatically increases the system output volume following engine start.

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 1-2
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
The amplifier is thermal and short circuit protected to prevent damage. The built in power supply is
overcurrent and reverse polarity protected.
Front panel switches provide selection of the various operational modes of the LSC22 including a
VOL/PWR which provides volume control of the selected output and a means of turning off the system.
One front panel Auxiliary input jack provides both an input audio from an external device and a
maintenance mode USB connection that enables loading of audio wave files.
1.4 Specifications
1.4.1 Electrical Specifications
1.4.1.1 Input Operating Voltage
Normal Operating Conditions:
Nominal: +28.0 Vdc
Maximum: +30.3 Vdc
Minimum: +22.0 Vdc
Emergency: +18.0 Vdc
Abnormal Operating Conditions:
Maximum: +32.2 Vdc
Minimum: +20.5 Vdc
1.4.1.2 Input Operating Current
Input Current:
2.0 A max @ 28.0 Vdc
0.2 A idle max @ 28.0 Vdc
Backlighting Current:
28V Lights Power: 10 mA max @ +28.0 Vdc
5V Lights Power: 10 mA max @ +5.0 Vdc

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 1-3
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
1.4.1.3 Input Signals
Microphone Audio (MIC HI)
Quantity: 1
Microphone Type: Amplified dynamic/electret
Circuit Type: Single-Ended
Rated Level: 250 mVrms (TBD) ± 10%
Impedance: 150 Ohm ± 10%
Mic Bias: +12Vdc min
Compression: 85 mVrms rotation point, 1.5:1 compression ratio
Radio Audio Input (RADIO HI)
Quantity: 1
Circuit Type: Single-Ended
Rated Level: 2.5 Vrms ± 10%
Impedance: 1 kOhm ± 10%
Auxiliary Audio Input Interface Connector (AUX LEFT/AUX RIGHT)
Quantity: 1
Circuit Type: Single-Ended, Stereo
Rated Level: 500 mVrms ± 10%
Impedance: 1 kOhm ± 10%
Compression: 200 mVrms rotation point, 1.5:1 comp ratio
Auxiliary Audio Input Front Panel Jack (AUX LEFT/AUX RIGHT)
Quantity: 1
Circuit Type: Single-Ended, Stereo
Rated Level: 500 mVrms ± 10%
Impedance: 1 kOhm ± 10%
Compression: 200 mVrms rotation point, 1.5:1 comp ratio
Mic Key Input (MIC KEY)
Quantity: 1
Rated Level: Gnd (active low), 1 Vdc maximum
Current In: ≤10 mA
-3 dB Control Input (-3DB SELECT)
Quantity: 1
Rated Level: Gnd (active low), 1 Vdc maximum
Current In: ≤10 mA
Siren Key Input (SIREN KEY)
Quantity: 1
Rated Level: Gnd (active low), 1 Vdc maximum
Current In: ≤10 mA
Play Once Input (PLAY ONCE)
Quantity: 1
Rated Level: Gnd (active low), 1 Vdc maximum
Current In: ≤10 mA

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 1-4
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
1.4.1.3 Output Signals
Internal PA Audio (INT PA HI/LO)
Quantity: 1
Circuit Type: Differential
Rated Level: 25W (14.15 ± 10% Vrms)
Rated Load Impedance: 8 Ohms ± 10%
Output Impedance: ≤ 3 Ohms
Frequency Response: ≤ 3 dB from 200 Hz to 6 kHz
Distortion: ≤ 10% @ rated output
Audio Noise Level: ≥-60 dB from rated output
Sidetone Audio (SIDETONE HI/LO)
Quantity: 1
Circuit Type: Balanced
Rated Level: 7.75 Vrms ± 10%
Rated Load Impedance: 600 Ohms ± 10%
Output Impedance: ≤ 75 Ohms
Frequency Response: ≤ 3 dB from 200 Hz to 6 kHz
Distortion: ≤10% @ Rated output
Audio Noise Level: ≥-60 dB from rated output
External PA Audio (EXT PA HI/LO)
Quantity: 1
Circuit Type: Balanced
Rated Level: Selectable
500 mVrms ± 10% (LSA400/800, PA250/700) or
6.5 Vrms ± 10% (PA110/PA220)
Rated Load Impedance: 600 Ohms ± 10%
Output Impedance: ≤ 75 Ohms
Frequency Response: ≤ 3 dB from 200 Hz to 6 kHz
Distortion: ≤10% @ Rated output
Audio Noise Level: ≥-60 dB from rated output
Switched Power Output (SWITCHED POWER)
Quantity: 1
Rated Level: 26.5 Vdc (active high)
Current Output: 0.4 A maximum, over-current protected

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 1-5
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
1.4.2 Physical Specifications
Height 1.11” [28.2mm]
Depth (behind panel) 6.34” [161.0mm]
Depth (behind panel including connectors) 6.59” [167.4mm]
Width (behind panel) 4.84” [122.9mm]
Width (front panel) 5.74” [145.8mm]
Weight 1.2 lbs (0.54 kg)
Mounting Dzus rail (4 fasteners), 0.375” vertical spacing
with Allen key head (0.094” across the flats).
Dzus stud head has custom diameter of 0.300”.
Connectors One 25 pin male D-subminiature with V5 locks
One 9 pin male D-subminiature with V5 locks
One 3.5mm, 4 conductor jack
Material/Finish Enclosure shall be conversion coated aluminum.
Finish is clear conversion coating per MIL-DTL
Type II Class 3
Bonding ≤2.5 mΩ
1.4.3 Environmental Specifications
Temperature -40 to +70C (operating)
-55 to +85C (survival)
Altitude 35,000 feet max.
Humidity 95% Non-condensing
Operational Shock 6g for 11msec (any axis)
Crash Safety Shock 20g for 11 msec (impulse), 3 sec (sustained)
Vibration DO-160G category ‘S’curves B & M
DO-160G category ‘U2’curves F & F1
Qualification of the LSC22 Loudspeaker Controller was completed in accordance with
DO-160G Env. Cat. C4-BAB[SBM][U2FF1]XXXXXXZ[BXX]AB[ACE]XMXXXAX.
Note: Refer to Environmental Qualification Form located in Section 2 of this Manual for complete details
of the environmental categories.

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 1-6
ENG-FORM: 800-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
1.4.4 Product Approval/Certification
None
1.5 Unit Nomenclature
LSC22-001
Dzus mount Loudspeaker Controller
Blue/White Panel Lighting
LSC22-001N
Dzus mount Loudspeaker Controller
NVIS Green A Panel Lighting
End of Section 1.0

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 2-1
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Section 2.0 Installation
2.1 Introduction
Information in this section consists of: unpacking and inspection procedures, installation procedures, post-
installation checks, and installation drawings.
2.2 Unpacking and Inspection
Unpack the equipment carefully. Inspect the unit visually for damage due to shipping and report all such
claims immediately to the carrier involved. Note that each unit should have the following:
- LSC22
- USB Type A to 3.5mm 4 conductor cable
- Certificate of Conformity or Release certification
Verify that all items are present before proceeding and report any shortage immediately to your supplier.
2.2.1 Warranty
All Anodyne Electronics Manufacturing Corp. (AEM) products are warranted for 2 years. See the website
www.aem-corp.com/warranty for complete details.
2.3 Installation Procedures
2.3.1 Warnings
WARNING:
High volume settings can cause hearing damage. Set the volume
control to the minimum volume setting prior to conducting tests, and
slowly increase the volume to a comfortable listening level.
WARNING:
When the LSC22 is connected in a speaker amplifier system, the
system is capable of producing high sound pressure levels. Proper
personal protective equipment is required to prevent hearing damage.
2.3.2 Cautions
CAUTION:
Do not remove components or external connections (with the exception of the
AUX input) from the product while the unit is turned on. This could cause
damage to the component or unit.

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 2-2
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
2.3.3 Cabling and Wiring
All wire shall be selected in accordance with the original aircraft manufacturer's Maintenance Instructions
or AC43.13-1B Change 1, Paragraphs 11-76 through 11-78. Unshielded wire types shall qualify to MIL-W-
22759 as specified in AC43.13-1B Change 1, Paragraphs 11-85, 11-86, and listed in Table 11-11. For
shielded wire applications, use Tefzel MIL-C-27500 shielded wire with solder sleeves (for shield
terminations) to make the most compact and easily terminated interconnect. Follow the interconnect
drawing in Section 2.7 as required.
Allow 3" from the end of the shielded wiring to the shield termination to allow the connector hood to be
easily installed. Refer to the interconnect drawing in Section 2.7 for shield termination details. Aircraft
harnessing shall permit the unit to be removed for easy access to all adjustments.
Maintain wire segregation and route wiring in accordance with the original aircraft manufacturers
Maintenance Instructions.
Unless otherwise noted, all wiring shall be a minimum of 22 AWG, except power, ground, and internal pa
speaker lines, which shall be a minimum of 20 AWG. Reference the Interconnect drawing for additional
specifications. Check that the ground connection is clean and well secured, and that it shares no path with
any electrically noisy aircraft accessories such as blowers, turn and bank instruments or similar loads.
Power to this unit must be supplied from a separate circuit breaker or fuse (fast blow), and not attached to
any other circuit breaker without additional protection. Verify that the selected circuit breaker size and wire
gauge are adequate for the installation using the techniques specified in AC43.13-1B Change 1,
Paragraphs 11-47 through 11-51 and 11-66 through 11-69.
2.3.4 Post-Installation Checks
Ensure all connectors are tight and the mechanical installation is sound.
2.3.4.1 Voltage/Resistance Checks
Do not connect the LSC22 to the wiring harness until the following conditions are met.
Check the following, refer to Section 2.7 for complete wiring details:
a) Check P101 pins 1, 2 for +28 Vdc relative to ground.
b) Check P101 pin 4 for continuity to chassis ground (less than 0.5).
b) Check P101 pins 14, 15, 16 and P102 pin 6 for continuity to ground (less than 0.5).
c) Check P101 pin 3 for 28V lighting voltage relative to ground or P102 pin 1 for 5V lighting voltage
relative to ground.
2.3.4.2 Power On Checks
Power up the aircraft’s systems and confirm normal operation of all functions of the LSC22. Refer to Section
3 (Operation) for specific operational details.
Upon satisfactory completion of all performance checks, make all required log book entries, electrical load,
weight and balance amendments and other documentation as required by your local regulatory agency
before releasing the aircraft for service.

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 2-3
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
2.4 Adjustments and Connections
The unit is shipped from the factory with all internal adjustments set to the rated input test levels to achieve
the rated output levels. Once installed in the aircraft, it may be desirable to change some of these settings
to best suit the local operating environment. The internal adjustments are located on the left side of the unit
when viewed from the faceplate:
User adjustable potentiometer adjustements (clockwise = increasing):
Adjustment
Description
MIC
Microphone Audio Input
RAD
Radio Audio Input
ST
Sidetone Audio Output
AUX
Auxiliary Audio Input
INT
Internal PA Audio Output
EXT
External PA Audio Output
MSG
Message Audio
SRN
Siren Audio
User selectable options for the EXT, MSG, MIC switches are as a follows:
Switch
Description
Up Position
Down Position
EXT
External PA Level Output
6.5 Vrms
0.5 Vrms*
MSG
Messages Played on INT PA
Yes
No*
MIC
Microphone Key Input Type
Live
Keyed*
* - Default Position
2.5 Accessories Required But Not Supplied
Installation kit p/n LSC22-IKC (crimp) is required to complete the installation. The kits consists of the
following:
LSC22-IKC consists of
Quantity Description Part No.
1 D-min 25 Socket Housing 20-21-025
1 D-min 9 Socket Housing 20-21-009
34 MS Crimp Socket 20-26-901
1 25 Pin JVL Hood/Locklever 20-29-250
1 9 Pin JVL Hood/Locklever 20-29-090

LSC22 Loudspeaker Controller
ASM-LSC22 Installation and Operation Manual
January 24, 2017 Rev: 1.00 Page 2-4
ENG-FORM: 805-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
2.6 Continued Airworthiness
Maintenance of the LSC22 Loud Speaker Controller is ‘on condition’ only. Periodic maintenance of this
product is not required.
2.7 Installation Drawings
Use of the "#" symbol in the REV. column indicates that the document is listed elsewhere in the manual.
Refer to the applicable AEM Part No. to locate the referenced document.
DOCUMENT
REV
DESCRIPTION
TYPE
SERIAL NO.
LSC22-001-403-0
1.00
Loudspeaker Controller
Interconnect
66517+
LSC22-001-405-0
1.00
Loudspeaker Controller
Connector Map
66517+
LSC22-001-521-0
1.00
Loudspeaker Controller
Environmental Qualification Form
66517+
LSC22-001-922-0
1.00
Loudspeaker Controller
Mechanical Installation
66517+
Section 2.0 ends following above documents

SHEET:
UNLESS OTHERWISE SPECIFIED:
SCALE: DRAWING No.:
REVISION
PART No.:
A
PAPER SIZE:
TITLE:
NAME DATE
CHECKED
DRAWN
FINISH:
MATERIAL:
DIMENSIONS ARE IN INCHES [MM]
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
CAGE CODE
CONFIDENTIAL AND PROPRIETARY
APPROVED
L9015
ANODYNE
ELECTRONICS
MANUFACTURINGCORP.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
DO NOT SCALE DRAWING
TOLERANCES:
FRACTIONAL_____________
ANGULAR_______________
TWO DECIMAL PLACE____
THREE DECIMAL PLACE___
±0.0625"
±0.5°
±0.010"
±0.005"
LSC22-001 1.00
403-0 1 of 3
SK
NOV 28/16
N/A
N/A
N/A
LOUDSPEAKER CONTROLLER
INTERCONNECT
Jan 4, 2017
Jan 4/17

SHEET:
UNLESS OTHERWISE SPECIFIED:
SCALE: DRAWING No.:
REVISION
PART No.:
A
PAPER SIZE:
TITLE:
NAME DATE
CHECKED
DRAWN
FINISH:
MATERIAL:
DIMENSIONS ARE IN INCHES [MM]
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
CAGE CODE
CONFIDENTIAL AND PROPRIETARY
APPROVED
L9015
ANODYNE
ELECTRONICS
MANUFACTURINGCORP.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
DO NOT SCALE DRAWING
TOLERANCES:
FRACTIONAL_____________
ANGULAR_______________
TWO DECIMAL PLACE____
THREE DECIMAL PLACE___
±0.0625"
±0.5°
±0.010"
±0.005"
LSC22-001 1.00
403-1 2 of 3
SK
NOV 28/16
N/A
N/A
N/A
LOUDSPEAKER CONTROLLER
INTERCONNECT
Jan 4, 2017
Jan 4/17

SHEET:
UNLESS OTHERWISE SPECIFIED:
SCALE: DRAWING No.:
REVISION
PART No.:
A
PAPER SIZE:
TITLE:
NAME DATE
CHECKED
DRAWN
FINISH:
MATERIAL:
DIMENSIONS ARE IN INCHES [MM]
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
CAGE CODE
CONFIDENTIAL AND PROPRIETARY
APPROVED
L9015
ANODYNE
ELECTRONICS
MANUFACTURINGCORP.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
DO NOT SCALE DRAWING
TOLERANCES:
FRACTIONAL_____________
ANGULAR_______________
TWO DECIMAL PLACE____
THREE DECIMAL PLACE___
±0.0625"
±0.5°
±0.010"
±0.005"
LSC22-001 1.00
403-2 3 of 3
SK
NOV 28/16
N/A
N/A
N/A
LOUDSPEAKER CONTROLLER
INTERCONNECT
Jan 4, 2017
Jan 4/17

SHEET:
UNLESS OTHERWISE SPECIFIED:
SCALE: DRAWING No.:
REVISION
PART No.:
A
PAPER SIZE:
TITLE:
NAME DATE
CHECKED
DRAWN
FINISH:
MATERIAL:
DIMENSIONS ARE IN INCHES [MM]
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
CAGE CODE
CONFIDENTIAL AND PROPRIETARY
APPROVED
L9015
ANODYNE
ELECTRONICS
MANUFACTURINGCORP.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
DO NOT SCALE DRAWING
TOLERANCES:
FRACTIONAL_____________
ANGULAR_______________
TWO DECIMAL PLACE____
THREE DECIMAL PLACE___
±0.0625"
±0.5°
±0.010"
±0.005"
LSC22-001 1.00
405-0 1 of 2
SK
NOV 28/16
N/A
N/A
N/A
LOUDSPEAKER CONTROLLER
CONNECTOR MAP
Jan 4, 2017
Jan 4/17

SHEET:
UNLESS OTHERWISE SPECIFIED:
SCALE: DRAWING No.:
REVISION
PART No.:
A
PAPER SIZE:
TITLE:
NAME DATE
CHECKED
DRAWN
FINISH:
MATERIAL:
DIMENSIONS ARE IN INCHES [MM]
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
ANODYNE ELECTRONICS MANUFACTURING.
ANY REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
ANODYNE ELECTRONICS MANUFACTURING IS
PROHIBITED.
CAGE CODE
CONFIDENTIAL AND PROPRIETARY
APPROVED
L9015
ANODYNE
ELECTRONICS
MANUFACTURINGCORP.
KELOWNA BC CANADA
(250)-763-1088
WWW.AEM-CORP.COM
DO NOT SCALE DRAWING
TOLERANCES:
FRACTIONAL_____________
ANGULAR_______________
TWO DECIMAL PLACE____
THREE DECIMAL PLACE___
±0.0625"
±0.5°
±0.010"
±0.005"
LSC22-001 1.00
405-1 2 of 2
SK
NOV 28/16
N/A
N/A
N/A
LOUDSPEAKER CONTROLLER
CONNECTOR MAP
Jan 4, 2017
Jan 4/17

ENVIRONMENTAL QUALIFICATION FORM
Description:
Loudspeaker Controller
Document:
LSC22-001-521-0100
Part #:
LSC22-001
TSO #:
N/A
Manufacturer’s Specification and/or Other Applicable Specification:
Manufacturer:
Anodyne Electronics Manufacturing Corp.
Address:
#15 - 1925 Kirschner Rd., Kelowna, BC, Canada. V1Y 4N7
DO-160 Rev:
G
Prepared By:
Checked By:
Approved By:
Rev: 1.00 Jan 25, 2017 Page 1 of 4
ENG-FORM: 521-0100.DOTX
CONFIDENTIAL AND PROPRIETARY TO ANODYNE ELECTRONICS MANUFACTURING CORP.
Conditions
Section
Description of Conducted Tests
Temperature and Altitude
Ground Survival Low Temp
Short
-Time Operating Low Temp
Operating Low Temp
Ground Survival High Temp
Short
-Time Operating High Temp
Operating High Temp
In
-flight Loss of Cooling
Altitude
Decompression
Overpressure
4.0
4.5.1
4.5.1
4.5.2
4.5.3
4.5.3
4.5.4
4.5.5
4.6.1
4.6.2
4.6.3
Equipment tested to Categories
C4
-55° C
-4
0° C
-4
0° C
+85° C
+70° C
+7
0° C
N/A
+
35,000 ft (+10,700 m)
N/A
N/A
Temperature Variation
5.0
Equipment tested to Category B
± 5° C/min.
Humidity
6.0
Equipment tested to Category A
95% RH for 48 hrs.
Operational Shocks and Crash Safety
Operational Shocks
Crash
Safety Impulse
Crash Safety Sustained
7.0
7.2.2
7.3.2
7.3.3
Equipment tested to Category B
6 g for 11 ms in all axes
20 g for 11 ms in all axes
20 g for 3 s in all axes
Steve Kempf
Designer
Jan 25/17
Nikolis Andrews
Designer
Jan 31 2017
Todd Blackstock
R&D Manager
Jan 31/17