AEONS Technologies SP Series User manual

Models: 6U, 9U, 12U, 15U, 18U, 22U
Owner’s Manual
Rev. 1.2
AEONS SP Series Wall-Mounted Enclosure
Applied to Model Series: SPxx06, SPxx09, SPxx12, SPxx15, SPxx18, SPxx22
aeonstech.com
[email protected]
1644 N Maple Street, Corona, CA 92880
www.aeonstech.com/support
Copyright © 2020 Aeons LLC. All rights reserved.
*actual product may vary from picture

1
This manual contains instructions and warnings that must be followed during the
installation and operation of the product. Failure to comply may invalidate the warranty and
cause property damage or personal injury.
Keep the enclosure in a controlled indoor environment, away from moisture, temperature
extremes, flammable liquids and gasses, conductive contaminants, dust, and direct sunlight.
Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not
block, cover or insert objects into the external ventilation openings of the enclosure.
The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt
to unpack, move or install it unassisted. Use a mechanical device such as a forklift or pallet
jack to move the enclosure in the shipping container. Inspect the shipping container and the
enclosure for shipping damage. Do not use the enclosure if it is damaged. Leave the
enclosure in the shipping container until it has been moved as close to the final installation
location as possible.
Use caution when cutting packing materials. The enclosure may be scratched, causing
damage not covered by the warranty. Save all packing materials for later use. Repacking and
shipping the enclosure without the original packing materials may cause product damage
that will void the warranty.
Install the enclosure in a structurally sound area capable of handling the load, or on a level
floor that is able to bear the weight of the enclosure, all equipment that will be installed in
the enclosure and any other enclosures and/or equipment that will be installed nearby. For
permanent wall mounting, be sure to securely fasten the enclosure to the building structure
before operation. Do not place any object on the enclosure, especially containers of liquid,
and do not attempt to stack the enclosures.
Important Safety Instructions
Overview
Thank you for purchasing the AEONS enclosure product.
The AEONS signature series enclosures accommodate all standard 19-inch rackmount
equipment. They feature premier quality, heavy-duty cabinets in various U sizes for quick and
easy deployment.
Our enclosures include quick-release doors and side panels for convenient maintenance.
Front access doors are reversible for installation flexibility. Front door and side panels are
lockable. An optional rolling caster kit (optional for 15U-22U) is available for easy
maneuvering of enclosures.

2
1. Top Panel
2. Cable Access Cover
3. Hanger Bar
4. Back Panel
5. L Mounting Bracket
6. Side Panels
7. Frames
8. Vertical Mounting Rails
9. Bottom Panel
10. Front Door
11. Accessories
Parts Identification
Assembly Hardware Kits:
M8*12 Inner Hexagon Screw - 16pcs
M8 Flange Nut - 16pcs
M6*12 screw - 4pcs
M6 Cage Nut - 4pcs
M6 Plastic washer - 4pcs
M4 self-tapping screw - 17pcs
User Hardware Kits:
U capacity ≤12U, 12 sets cage nuts;
U capacity＞12U, 24 sets cage nuts.
(cage nut set: M6*12 screw & plastic washer, M6 Cage Nut)
M5self-tapping screw - 8pcs
Lock kit - 1pcs
White Plastic Washer - 1pcs
Anchors - 4pcs
Ground Wire Kit - 1pcs
Keys - 2pcs
Casters - 4pcs (Optional only for 15U-22U)
Accessories List
1 2 3
4
5
6
78910

3
Assembly Steps
Step 1: Install Bottom Panel and Frames
Lay down Bottom Panel (#9) on a flat surface. Insert Left
and Right Frames (#7) with large flange oriented to the
inside. Ensure that the slots in the center of the frames are
facing inward as shown in the detailed view.
Secure with 8x M8 Hexagon Screws and 8x M8 Flange Nuts
from bottom, and 2x M4 self-tapping screws from front.

4
Step 2: Install Top Panel and Frames
Place the Top Panel (#1) on a flat surface. Turn the assembly
over and insert it into the top panel. Ensure that the Top and
Bottom Panels (#1 and #9) are oriented in the same direction.
Secure with 8x M8 Hexagon Screws and 8x M8 Flange Nuts
from bottom, and 2x M4 self-tapping screws from front.

5
Step 3: Install Vertical Mounting Rails
Install the 4 Vertical Rack Rails (#8) to
the horizontal rails at the desired depth
using the M5 self-tapping screws
provided. When determining the
appropriate depth, make sure consider
the equipment that you plan to mount
inside the enclosure, and the rail depth
is the same on both sides of the cabinet.
Step 4: Install L Type Mounting Bracket
Mount L Brackets (#5) to the Vertical
Mounting Rails on each side of the
cabinet using the Cage Nut Kit provided.
Note: To mount the L Type Mounting
Brackets (#5), the depth between front
and back vertical rails should be 11’’
(280mm) for 450mm depth cabinet and
16.9’’ (430mm) for 600mm depth
cabinet.)

6
Step 5: Install Side Panel
Install the two Side Panels (#6) into
place using the Side Panel Latches.
Once each Side Panel (#6) is
attached, test to ensure that each
Side Panel Lock locks properly.
Step 6: Install Front Door Lock
Install the Front Door Lock to the
Front Door (#10) as shown in the
left picture.

7
Step 7: Install Front Door
To attach the Front Door (#10) to the cabinet, locate
the side with two pins. Insert the bottom fixed pin with
White Plastic Washer into the door hinge hole. With
your thumb, pull down on the top spring pin and slide it
into place over the second door hinge hole and release.
NOTE: Each side of the front of the cabinet has door
hinge holes; this allows you to choose the door swing
orientation.

8
Step 8: Install Back Panel
Attach the Back Panel (#4) to the cabinet
using 6x M4 Self-tapping Screws.
Step 9: Install Hanger Bar
Attach the Hanger Bar (#3) to a wall or other suitable
mounting surface using 4 appropriate anchors.
NOTE: Make sure the mounting hooks are
facing outwards.

9
Step 10: Mount the Enclosure
Fit the cabinet’s 2 mounting notches onto the 2 mounting
hooks on the hanger bar. The enclosure should slide down
onto the hooks until secure.
After the cabinet hung properly, secure the cabinet to the
hanger bar using 2 M4 Screws from inside of cabinet to the
holes on the mounting hooks as shown.

10
Step 11: Install Casters (Optional and only
available for 15U, 18U and 22U versions)
Attach Casters using 16x M6 Self Tapping
Screws to Bottom Panel (#9).

11
Technical Support
Thank you for purchasing the Aeons product. We intends this manual to guide you through a
smooth installation. Aeons assumes that you are qualified in the servicing of IT equipment
and trained in recognizing any hazards that may occur in the installation of this product. Our
lifetime technical support is an integral part of our commitment to provide industry-leading
solutions. If you ever need help with our product, visit www.aeonstech.com and submit your
Technical Support Request online or email your request to [email protected].
Limitations of Liability
Different wall materials require different type of anchoring devices. Please contact a
specialist for advice on suitable anchoring systems. Aeons is not liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing,
performance, or use of this material.
Aeons assumes no responsibility for the use, application, or reliability of the software or
hardware that you install into the product.
It is highly recommended that installation of this product be performed by a qualified and
experienced installer. Improper installation of this product could result in damage to the
product, other equipment, or personal injury. Aeons cannot be held responsible for damage
to equipment or personal injury resulting from improper use, installation or the misuse of
information presented in this document.
Use of Trademarks and other Protected Names and Symbols
This manual may make reference to trademarks, registered trademarks, and other protected
names and/or symbols of third-party companies not related in any way to Aeons. These
references are for illustrative purposes only and do not represent an endorsement of a
product or service by us, or an endorsement of the product(s) to which this manual applies
by the third-party company in question. Regardless of any direct acknowledgement
elsewhere in the body of this document, we hereby acknowledges that all trademarks,
registered trademarks, service marks, and other protected names and/or symbols contained
in this manual and related documents are the property of their respective holders.