Aeramax professional Am iii User manual

INSTALLATION GUIDE

AeraMax

PRO Air Quality Control System: AM III

Please read instructions carefully before installing unit

Fellowes, Inc.

1789 Norwood Ave

Itasca, Illinois 60143-1095 USA

630-893-1600

1-800-477-7940

Product Support: 1-800-945-4545

www.aeramaxpro.com

AeraMaxPRO_AMIII_InstallGuide_408530_RevB_111314.indd 8-1 11/13/14 11:01 AM

ENGLISH

AeraMax® PRO Air Quality Control System: AM IV

SAFETY

TOOLS REQUIRED FOR INSTALLATION

PARTS PROVIDED FOR INSTALLATION

PRODUCT INSTALLATION GUIDELINES

WARNING: To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before beginning any installation work.

Confirm no electrical wiring, utility pipes, or duct work is located directly behind the installation / drilling area.

On a stud wall, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to an existing stud.

• Electricdrill,drillbits(notincluded)

• #2Phillipsand#2FlatHeadscrewdrivers(notincluded)

• Wirenuts(notincluded)

• Level(notincluded)

• Mountingtemplate(included)

• DrywallAnchors-10mmOD

• PanHeadPhillipsScrews

1. Accesspanel

2. Filters

3. Filterframe

4. Main Assembly

5. Power Switch

6. Access panel latch

7. Access panel lock

8. Rear housing assembly

9. Control panel

10. Filterframewindow

KEY

Fig1

8”

12”

27”

8”

27”

80”

8”

Fig2

Americans with Disabilities Act (ADA):

BesuretofollowallADAguidelinespertainingto“Objectsprotruding

intoacirculationpath.”Formoreinformationvisitwww.ada.gov.

Place the mounting template provided on the wall where the air

purifier is to be installed. If air purifier is being mounted high on

the wall make sure the top edge of the unit is positioned at least

8”inches(21cm)belowtheceilingtoallowforfilterreplacement

(seeFig2).

AeraMaxPRO_AMIII_InstallGuide_408530_RevB_111314.indd 2-3 11/13/14 11:01 AM

Place the air purifier face up on a

flat, stable work surface. Open the

access panel by pressing in latches

oneachsideoftheunit(Fig3).

Make sure filters are in correct

order-pre-filter/carbonfilter/

HEPAfilter-andinsertedintofilter

frame(Fig16).

Oncetheunitisclosedre-establish

power.Lightsonthecontrolpanel

will be visible through the lens,

indicating the unit is operational

(Fig20).Thepowerlightindicator

will flash once a second.

IMPORTANT: Make sure filter

detection area aligns with window

infilterframe(Fig17).

Using provided template ensure electrical

outletboxislocatedbehindcablehole(A)

in Rear Housing assembly (Fig 9). Drill

holes and place anchors in wall.

If mounting on concrete, cinder block or

brick type walls route the wires through

the“punch-out”holemarked(B)inFig9.

Disconnect main housing assembly

from rear housing assembly.

Separate main housing from rear

housing.Liftmainhousingassembly

away from rear mounting housing

(Fig8).

Close front panel by pressing

firmly until both sides latch closed

(Fig19).

Open access panel and remove

filter assembly by pulling out on

top of side edges of frame, then

lifting. NOTE: remove all plastic

wrapfromfilters(Fig4).

Check for washers at all mounting

screw locations (Fig 10). Pull wires

from electrical outlet box through

hole in rear housing. Align housing

over anchors and securely install all

mounting screws.

The power connector (B, in Fig

12)willcarrypowerfromtherear

housing to the main housing once

the assemblies are fully seated.

The main assembly will attach to

the rear housing assembly by the

four screws previously removed

(Fig5&6).Twosnaphooks(A,

inFig12)willholdthemainand

rear assemblies together until the

screws can be installed.

Removethefourhousingscrews(Fig5&6)andsetasideforre-assembly. Carefully align the main assembly

with the rear housing assembly.

Slowly press into place until snap

is heard, and there is no gap

betweentheassemblies(Fig13).

The unit should now support its

own weight.

At the location of the two upper

housingscrews(Fig5),insertaflat

head screwdriver and gently twist

to release tab as shown in Fig 7.

This will disconnect main housing

assembly from the rear housing

assembly.

Open front panel by pressing

latches on both sides of unit. Allow

door to open fully. Insert filters

– IMPORTANT: make sure filter

detection window is aligned in

upperrightcorner(Fig18).

To restrict access to the control panel

and filters the unit can be locked. To

lock, insert the key provided and

rotateclockwise¼turn(Fig21).

Attachwiresfromelectricaloutletboxtowireslocatedinsiderearhousingusingwirenuts.Matchupline(black)andneutral(white)wires(Fig11).Makesure

all connections are made in accordance with federal, state and local codes and regulations.

Installfourscrews(previouslyremoved)tosecuremainassemblytorear

housingassembly(Fig14&15).

MOUNTING REAR HOUSING AND MAIN ASSEMBLY

RE-INSTALLING FILTERS

LOCKING ACCESS PANEL

MAIN ASSEMBLY INSTALLATION

REAR HOUSING INSTALLATION & WIRING

Test the electrical outlet box first to ensure rated power requirements are met before beginning installation.

Remove air purifier from its shipping carton and remove all packing material.

Reference rear housing and locate desired mounting location. Again, it is strongly recommended at least 2 mounting anchors for the air purifier be mounted to

an existing stud.

1 2

3 4

1 2

3 4

1 2

3 4

1 2

3 4

WARNING: To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before continuing any installation work.