Aerfast TS55-14V User manual

MODEL: TS55-14V

△,!WARNING
Operating instructions
CORDLESS AUTOFEED SCREW DRIVER MODEL TS55 14V
General Safety Instructions
Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury. Save all
warnings and instructions for future reference! The term "power tool" in the
warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled cords increase the risk of electric
shock.
e. When operating a power tool outdoors, use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f. If operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions will reduce personal
injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on.
1.

A wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used. Use
of dust collection can reduce dust related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the rate
for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c. Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation.
5. Battery tool use and care
a. Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery pack may create a risk of fire
when used with another battery pack.
b. Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
c. When battery pack is not in use, keep it away from other metal objects,
like paper clips, coins, keys, nails, screws or other small metal objects,
that can make a connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d. Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or burns.
6. Service
a. Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
2.

△,!WARNING
Product Safety Instructions
△,!WARNING
Important Safety Instructions for Charger & Battery Pack
1. To ensure the designed operational integrity of power tools, do not remove
installed cover or screws.
2. Use your tool at lower input than specified on the nameplate, otherwise, the
finish may be spoiled and working efficiency reduced by motor overload.
3. Do not wipe plastic parts with solvent. Solvents such as gasoline, thinner,
benzene, carbon tetrachloride, alcohol, ammonia and oil containing chloric
annex may damage and crack plastic parts. Do not wipe them with such
solvent. Wipe plastic parts with a soft cloth lightly dampened with soap water.
4. Use clamps or other practical way to secure and support the work piece to a
stable platform. Holding the work by hand or against your body is unstable and
may lead to a loss of control.
5. Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may create a risk of injury
when used on another tool.
1. Caution：To reduce risk of injury, charge only specific type rechargeable
battery packs. Other types of battery packs may burst causing personal injury
and damage.
2. Before using charger, read all instructions and cautionary markings on battery
packs and chargers.
3. Do not expose charger to rain or snow.
4. To reduce the risk of damage to electric plug and cord, pull by plug rather than
cord when disconnecting charger.
5. Use of an attachment not recommended or sold by the charger manufacture
may result in a risk of fire, electric shock, or injury to persons.
6. Make sure cord is located so that it will not be stepped on, tripped on, tripped
over, or otherwise subjected damage or stress.
7. Do not operate charger with damaged cord or plug. Replace them
immediately.
8. Do not operate charger if it has received a sharp blow, been dropped, or
otherwise damage in any way, take it to qualified center.
9. To reduce risk of electric shock, unplug charger from outlet before attempting
any maintenance or cleaning. Turning off controls will not reduce this risk.
10. Do not disassemble charger or battery pack, take it to a qualified service
center while repair is required. Incorrect reassembling may result in a risk of
electric shock or fire.
3.

△,!WARNING
1. Do not charge battery pack when temperature is below 10°C (50°F) or
above 40°C (104°F).
2. Do not attempt to use a set-up transformer, an engine generator or DC
power receptacle.
3. Do not allow anything to cover or clog the charger vents.
4. Always cover the battery pack terminals with the battery pack cover
when the battery pack: is not used.
5. Do not short the battery pack:
6. Do not touch the terminals with any conductive material.
7. Avoid storing battery pack in a container with other metal objects
such as nails, coins, etc.
8. Do not expose battery pack to water or rain, A battery pack short can
use large current flow, overheating, possible burns and even a
breakdown.
9. Do not store the machine and battery pack in locations where the
temperature may reach or exceed 50°C (122°F)
10. Do not incinerate the battery pack even if it is severely damaged or
completely worn out. The battery pack can explode in a fire.
11. Be careful not drop, shake or strike battery pack.
12. Do not charge inside a box or container of any kind. The battery pack
must be placed in a well ventilated area during charging.
13. For extension of the battery lifetime, the lithium-ion battery is designed
with the protection function to stop the output.
In the case of described below, when using this product, even if you are
pulling the switch, the motor may stop.
This is not malfunction but the result of protection function.
When the battery power remaining runs out, the motor stops.
If the tool is overloaded, the motor may stop.
In this case, release the switch of tool and eliminate causes of
overloading. After that you can use it again.
If the battery is overheated under overload work, the battery power
may stop. In this case stop using the battery and let the battery cool.
After that you can use it again.
14. Do not leave batteries unused for extended period of time. Recharge
the battery every 3~6 months and bring Li-Ion battery to 40~80%
charge level before storage.
15. Li-Ion batteries are sensitive to high temperature and should be kept in
a cool, dry and out of direct light exposure. Ideal temperature for
operation and storage is below 77°F.
Additional Safety Rules for Charger & Battery Pack
16. This product is designed with low voltage protection, which prevents the tool
from over discharging and prolong battery's lifespan.
4.

Specifications
Model No.
TS55-14V
Voltage
14.4 V d.c.
No-Load Speed
4500 r.p.m(/min)
Max Torque
82 kg-cm/8N.m/5.9ft-lb
Size
L396 x W80 x H258mm
Tool Weight
(With Battery)
2.27 kg
(Battery0.53kg)
Fastener Range
25-55 mm length
Bit Spec.
1/4”x173Lmm
Charging Time
1 Hour Auto Cut-Off
Specific Safety Rules and/or Symbols
--------Recycle ------Class II Tool
--------Do Not Throw In Garbage V--------Volts
a.c.------Alternating Current Hz-------Hertz
W--------Watts kg-------Kilograms
mm------Millimeter d.c. -----Direct Current
kg-cm--Kilograms Per Centimeter ft-lb------Foot-Pound
/min-----Revolutions or Reciprocations Per Minute
5.

6BView of the Major Components
Accessories
Forward/Reverse Rod
Battery Pack
Main Switch
Battery Button
Conduction Ass’y
Hook
Hook Screw
Charger
Screw Length Adjust Button
Anti Slip Pad
Reverse Knob
Depth Control Knob
Quick Release Button
6.

Operating Instructions (Slide-In)
Installing or Removing Battery Pack
(See Fig.1 Fig.2 )
1. Always switch off the machine before insertion or
removal of the battery pack.
2. To remove the battery pack, push the button on the
battery pack and pull the tool unit from the battery
pack in the direction.
3. To insert the battery pack, align the tool unit slides
with the battery pack sliding groove and push the tool
unit into place.
The tool unit can be slide into battery pack in two
directions.
4. Do not force the battery pack in sliding it into tool unit.
If the battery pack does not slide in easily, it is not
being inserted correctly.
Charging the Battery Pack (See Fig.3)
1. Plug the fast charger into the power source.
2. Slide the battery pack into the charger as the arrow
direction shown on the charger.
3. Push the battery pack into place and make sure the
red light on the charger is “ON”. The battery pack is
now starting the charging cycle.
4. After finish the charging cycle, the light will turn into
green. The battery pack is now ready for use.
5. Your new battery pack is not charged. You need to
charge it before use.
6. If you try to charge a battery pack from a just-operated
machine, sometimes the charging light will not come
on. If this occurs, let the battery pack cool for a while
then re-insert it and try to charge again.
7. When you charge a new battery pack or a battery
pack which has not been used for a long period, it
may not accept a full charge. This is a normal
condition and does not indicate a problem. You can
recharge the battery pack fully after discharging it
completely a couple of times.
8. While charging the second battery, allow the charger
to cool down for 15 minutes before start the second
charging process.
9. Unplug the charger from the power source after finish
the charge.
Fig.1
Fig.2
Fig.3
1
2
7.

LED Indication Function
The Battery Pack has a “SW” button and 4-step green LEDs for indicating
remaining capacity status and Over temperature condition.
The remaining capacity (RC) and temperature protection status green LED
indications ( 3 second ) when the “SW” button is momentarily pressed.
Power On (Green light flashes slowly)
Battery Low (Red light stays illuminated)
Battery charged 80% (Green light flashes rapidly)
Battery charged 100% (Green light stays illuminated)
Battery Pack temperature is too hot or too cold (Red light flashes slowly)
Battery Pack malfunction (Red and Green lights stay illuminated)
Remaining Capacity LED Indication
RC Status
LED 1 (green)
0%- 25%
LED 1, 2 (green)
26%-50%
LED 1, 2, 3 (green)
51%-75%
LED 1, 2, 3, 4 (green)
76%-100%
LED 1 Blinking (0.25Sec/green)
Fully Depleted
LED 1, 2, 3, 4 Blinking (0.5sec/ green)
Over Temperature condition
The LED Light on the Charger
8.

△,!WARNING
1. Charger is plugged into a 100-240V a.c outlet only.
2. If the battery pack is too hot or too cold, the charger will not fast charge the
battery pack and the red Indicator light is “blinking”. When the battery pack
temperature returns to between 0C(32F) and 50C(122F), The charger
will automatically begin charging.
3. If both red and green indicator lights are “ON” the battery pack either does not
comply or is defective. Please contact your retailer.
4. Do not charge the battery pack in the rain, snow or high temperature
environment.
5. Do not charge battery pack when environment temperature is below
0C(32F)or above 40C(104F).
6. While charge the cool battery pack (below 0C) in the warm indoor, keep the
battery pack in the room for one hour to warm up before starting the battery
pack.
A cool battery may charge unsaturated.
7. Remove the plug after finishing the charge.
8. The charger should be cooled at least one hour after continue charging three
times.
9. Do not use generator for charging the battery pack.
9.

2BStrip Installation
1.Check the scale of the adjust is
totally consistent with length of the
screw.
This tool can be used in the following screw sizes.：
d(mm)
Φ3.5~Φ4.5mm
(#6~#8)
L(mm)
25
30
35
40
45
50
55
3. Feed the strip into the strip guide.
Screw Length
Screw Length Adjust Knob
Scale
Press
2.Press the screw length adjust knob
for the correct length of the screw.
Release the knob when the auto feed
assembly has adjusted to the proper
position. Please adjust the length of
screw first. Do not adjust the length
when the collated screw is on.
10.

Tool Operation
4. Move the strip forward until the
2nd empty slot is aligned with
the bit. This will allow for the
proper strip advancement once
the nosepiece is depressed.
2. Whenever possible, hold the
tool at a right angle to the
work surface.
Forward/Reverse Rod
(2)
(1)
Main Switch
1. Make sure the forward/reverse
rod direction ( )。
3.
(1)Pull the main switch to start
the motor.
(2)Press the conduction, with
constant force, against the
work surface.
Do not remove the tool from
the work surface until the
clutch disengages and the
bit stops rotating, signaling a
fully driven screw.
11.

Depth Control Knob
6. This tool has a depth sensing
clutch. When the screw is
countersunk to the pre-set
depth, it automatically
disengages and makes a
click or racheting sound. This
is normal and signals
completion of the drive.
4.Continue to allow the motor
to run.The next screw will be
automatically fed into place
when the tool is depressed
against the work surface.(3)
(3)
Depth Display
5. The depth display shows the
depth level. Adjust the depth
control knob for appropriate
depth. Please do not adjust
the depth control knob when
the depth display shows the
maximum level.
12.

To Remove the Screws
Replaceable Non Slip Pad
Caution
When the battery pack is low or the drive requires too much torque, the
tool may stall at the bottom of the drive (before the clutch can disengage).
Continuous operation in this manner can cause over-heating and
permanent damage.
Reverse direction
Reverse knob
Press
1.
(1)Remove the strip, pull it through
from the top of the nosepiece.
Pull the collated screw upward
for removing.When the screw
is out of position or stuck, push
the reverse knob while pulling
the collated screw downward at
the same time.
Push the forward / reverse rod
to reverse side ( ).
Depress nose piece while
inserting bit into screw.
(2)Maintain forward pressure on
tool.
(3)Pull the main switch to start
motor. Continue operation until
screw is completely
disengaged.
(2)
(1)
(3)
Main Switch
Forward /Reverse Rod
1. The non slip pad is self
replaceable if damaged or
dirty.
13.

Change the Driving Bit
Note: Use the bit provided by the manufacturer.
1.
1)Push the quick release
button backward first.
(2) then press down to
loose conduction ass’y
2. Remove conduction
ass’y.
3. Pull the ring-pull and
replace the bit.
After replacement
assemble conduction
ass’y and lock in
screw.
Conduction Ass’y
Bit
Ring-Pull
(2)
(1)
14.

Installing Extended Rod Ass’y
1. Remove conduction
ass’y and bit.
Conduction Ass’y Bit
3.
(1) Push the ring backward.
(2) Inject the bit.
2.
(1) Pull the ring-pull.
(2) Inject the extended
spindle.
(3) Inject the extended
rod.
※Pull the ring-pull of
the extended rod
can separate the
extended rod.
(2) (1)
Bit Ring
Ring-pull
Extended Spindle
(2) (1)
(3)
Extended Rod
Ring-pull
Conduction Ass’y
Extended Rod
Handle
4. Inject the conduction
ass’y .
The handle can be
adjusted 360 degrees,
based on the user's setting
(to tighten: clockwise/ to
loose: anti-clockwise)
15.

Installing Or Removing Hook
1. Installing Hook：
Use Phillips or slotted bit size bit and tighten in clockwise.
2. Removing Hook：
Use Phillips or slotted bit size bit to loosen the hook.
(1)
(2)
16.

Précautions d'utilisation
Avertissements généraux de sécurité pour l'outil
Lire tous les avertissements de sécurité et toutes les instructions. Ne pas suivre les
instructions de sécurité peut entraîner un choc électrique, un incendie et / ou des
blessures graves. Conserver tous les avertissements et les instructions comme
référence future! Le terme «outil électrique» dans ce manuel se réfère à votre outil
filaire ou sans fil, selon qu’il soit alimenté par le réseau électrique (filaire) ou un outil
électrique fonctionnant sur batterie (sans fil).
1. Sécurité du lieu
a. Garder la zone de travail propre et bien éclairée. Les endroits encombrés ou
sombres sont propices aux accidents.
b. Ne pas utiliser d'outils électriques dans des atmosphères explosives, telles qu’en
présence de liquides inflammables, de gaz ou de poussière. Les outils électriques
créent des étincelles qui pourraient enflammer les poussières ou les vapeurs.
c. Éloignez les enfants lorsque vous utilisez un outil électrique.
Les distractions peuvent vous faire perdre le contrôle.
2 Sécurité électrique
a. Les fiches des outils électriques doivent correspondre à la prise. Ne modifiez
jamais la fiche d’aucune façon. Ne pas utiliser d'adaptateurs de fiche avec mise à la
terre. Les fiches non modifiées et des socles adaptés réduiront le risque de choc
électrique.
b. Évitez tout contact corporel avec des surfaces mises à la terre tels que tuyaux,
radiateurs, cuisinières et réfrigérateurs. Il ya un risque accru de choc électrique si
votre corps est relié à la terre.
c. Ne pas exposer les outils électriques à la pluie ou à l'humidité. L’eau dans un outil
électrique augmente le risque de choc électrique.
d. Ne maltraitez pas le cordon. Ne jamais utiliser le cordon pour porter, tirer ou
débrancher l'outil électrique. Garder le cordon loin de la chaleur, de l'huile, des bords
tranchants ou des pièces mobiles. Les cordons endommagés ou emmêlés
augmentent le risque de choc électrique.
e. Lorsque vous utilisez un outil à l'extérieur, utiliser un cordon de rallonge adapté à
un usage extérieur. L'utilisation d'un cordon adapté à une utilisation extérieure réduit
le risque de choc électrique.
f. Si l’utilisation d’un outil électrique dans un endroit humide est inévitable, utiliser un
dispositif protégé (RCD). L'utilisation d'un RCD réduit le risque de choc électrique.
3. La sécurité des personnes
a. Restez alerte, regarder ce que vous faites et faites preuve de bon sens lorsque
vous utilisez un outil électrique. Ne pas utiliser un outil électrique si vous êtes fatigué
ou sous l'influence de drogues, d'alcool ou de médicaments. Un moment d'inattention
lors de l'utilisation d'outils électriques peut entraîner des blessures graves.
b. Utiliser un équipement de protection individuel. Toujours porter des lunettes de
protection.
INSTRUCTIONS UTILISATEUR
VISSEUSE AUTOMATIQUE Á BATTERIE POUR VIS EN BANDES. TS55-14V
1.

Les équipements de protection tels que les masques à poussière, des chaussures
de sécurité antidérapantes, un casque ou une protection auditive utilisés dans les
conditions appropriées réduiront les blessures personnelles.
c. Empêcher les démarrages intempestifs. S'assurer que le commutateur est en
position arrêt avant de brancher à une source d'alimentation et / ou de la batterie, de
ramasser ou transporter l'outil. Porter les outils en ayant le doigt sur l'interrupteur ou
sur l’interrupteur d’ outils électriques engendre les accidents.
d. Retirer toute clé (de réglage) avant de mettre l'outil en marche.
Un outil ou une clé de réglage attachée à une partie tournante de l'outil peut
entraîner des blessures.
e. Ne pas se précipiter. Conserver son équilibre en tout temps. Cela permet un
meilleur contrôle de l'outil électrique dans des situations imprévues.
f. Portez des vêtements adéquats. Ne pas porter de vêtements amples ou de bijoux.
Gardez vos cheveux, vêtements et gants éloignés des pièces mobiles. Les
vêtements amples, les bijoux ou les cheveux longs peuvent se prendre dans les
pièces mobiles.
g. Si des dispositifs sont prévus pour le raccordement d'aspiration de la poussière et
pour les installations de collecte, s'assurer qu'ils sont connectés et correctement
utilisés. Utiliser des collecteurs de poussière peut réduire les risques liés à la
poussière.
4 Utilisation des outils électroportatifs et entretien
a. Ne pas forcer l'outil de puissance. Utilisez l'outil électroportatif approprié pour
votre
application. L'outil adapté réalisera mieux le travail et de façon plus sûre à la vitesse
pour laquelle il a été conçu.
b. Ne pas utiliser l'outil si l’interrupteur ne permet pas de le désactiver. Tout outil qui
ne peut pas être contrôlé par son interrupteur est dangereux et doit être réparé.
c. Débranchez la fiche de la source d'alimentation et / ou la batterie de l'outil
électrique avant d'effectuer des réglages, de changer d’accessoires, ou de ranger
les outils électriques. Ces mesures de sécurité préventives réduisent le risque de
démarrage de l'outil en marche accidentellement.
d. Ranger les outils électriques inutilisés hors de la portée des enfants et ne pas
laisser des personnes non familiarisées avec l'outil ou sans ces instructions utiliser
l'outil. Les outils électriques sont dangereux dans les mains d'utilisateurs novices.
e. Entretenir les outils électriques. Vérifier l 'alignement ou le grippage des parties
mobiles, les ruptures des pièces et toute autre condition qui pourrait affecter le
fonctionnement de l'outil. S'il est endommagé, faites réparer votre outil avant de
l'utiliser. De nombreux accidents sont causés par des outils électriques mal
entretenus.
f. Maintenez vos outils propres. Des outils soigneusement entretenus sont moins
susceptibles de se coincer et sont plus faciles à contrôler.
2.