AeroBed R111USB User manual

INFLATION & ADJUSTMENTS
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE
AIR LEAKS.
NOTE: PRESSURE CAN VARY DEPENDING ON ROOM TEMPERATURE AND CONSUMER WEIGHT.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Air Release Valve is closed. If the release valve is open, close it by
using 2 thumbs to push cover and snap into valve. Be careful to avoid pushing valve cover
to the right or left as it snaps into the valve opening.
3. Remove the AC plug and cord from the plastic bag and
shrink wrap.
4. Plug into any standard polarized 120 Volt AC electrical outlet.
North American Electrical rating: 120 VAC 60 Hz 1.5 A.
(Note: 230 VAC product sold outside of North America). This
product has a polarized attachment plug (one blade is wider
than the other) as a safety feature. This plug will fit into a
polarized outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician. Never use with an extension cord unless
the plug can be fully inserted. Do not attempt to defeat this
safety feature.
5. On the Control Wand, press the UP arrow on the switch into the
“INFLATE” position to inflate your bed. Once bed has reached
desired firmness, return the switch to the off position “O”.
6. Lie on your bed and use the Control Wand to adjust the firmness
to your desired level. For a firmer bed, press the UP arrow on the
switch into the “INFLATE” position. For a softer bed, press the
down arrow “ADJUST” until desired firmness level is attained.
7. Once desired firmness is reached, ensure the switch is returned
to the off position “O”.
USB ChArgINg POrT
1. Your AeroBed®product includes a USB port built into the
pump for charging your personal device. Please adhere to the
following guidelines to ensure proper usage.
2. In order to charge your personal device
using the included USB port, the pump must
remain plugged into any standard polarized
120VoltAC electrical outlet throughout the
entire charging cycle.
3. For your convenience, directly below the
pump is a black mesh pocket that may be
used for storing your personal device throughout the charging cycle.
4. Once your device is fully charged, please disconnect the charging cable from the device
and from the USB port.
DEFLATION AND STOrAgE
1. To deflate your bed, open the Quick Release Valve and allow air to expel.
2. For the most compact storage, close the valve and use the Control Wand to press the
DOWN arrow on the switch into the “DEFLATE” position. After all the air is expelled from
the bed, return switch to the off position “O”.
3. Roll or fold the AC cord and wand cord and secure it. Fold the sides of the bed into the
center along its length. Tightly roll and place the bed in the convenient carry bag or other
storage solution and store in a dry, clean location.
4. Store your bed in a clean, dry place at room temperature (above 50 °F/10 °C). Storing your
bed under 50 °F (10 °C) and over 100 °F (38 °C) may affect its performance and will not
be covered under warranty.
SErVICINg OF DOUBLE-INSULATED PrODUCTS
In a double-insulated product, two systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated product, nor is a means for grounding
to be added to the product. Servicing a double-insulated product requires extreme care and
knowledge of the system, and is to be done only by qualified service personnel. Replacement
parts for a double-insulated product must be identical to the parts they replace.
INSTRUCTION MANUAL
R111USB
Thank you for joining the AeroBed®family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed®product. You are about to enjoy
the comfort of an AeroBed®product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed®product. Always instruct and supervise
others on your bed’s proper use, maintenance and safety.
IMPOrTANT SAFETY
INFOrMATION AND WArNINgS
SAVE ThESE INSTrUCTIONS
rEAD AND FOLLOW ALL INSTrUCTIONS
BEFOrE USINg ThIS PrODUCT.
Preparation of your AeroBed®product requires no tools. Use of tools may damage your bed.
When using an electrical furnishing, basic precautions should always be followed, including
the following: Read all instructions before using (this furnishing).
IMPORTANT
• Productisforindooruseonly.Donotuseoutdoors.ForHousehold/ResidentialUseOnly.
• Thisproducthasnotbeenevaluatedforammabilityorcigaretteignitionresistance.
WARNING
• Useonatsurfacesonly.Bedmaytipoveronunevensurfaces.
• Removeallsharpobjectsfromareawherebedwillbesetupandused.Donotusethis
bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.
• Unplugproductwhennotinuse.
• Pumpisnotintendedforcontinuoususe.Pumpmaystopworkingoroverheatifitis
used for extended periods of time.
• Donotusepumpcontinuouslyformorethan10minutes.
• Toavoidexcessiveheatbuild-upinpump,allowpumptocoolofffor30minutesafter
each 10 minutes of continuous use.
• Donotattempttodisassemble,repair,orservicethepump.Noserviceablepartsare
contained inside. Contact The Coleman Company, Inc. at 3600 North Hydraulic, Wichita,
KS 67219, 1-800-835-3278 or TDD 1-316-832-8707 in the United States or Sunbeam
Corporation (Canada) Limited, DBA Jarden Consumer Solutions at 20B Hereford Street,
Brampton ON L6Y 0M1, 1-800-387-6161 in Canada for repair and service
center information.
WARNING
This is an electrical product - not a toy. To avoid risk of fire, burns, injury, or shock:
• Alwaysunplugthisfurnishingfromtheelectricaloutletbeforecleaningorservicing.
• Usethisproductonlyforitsintendeduseasdescribedintheseinstructions.Donotuse
attachments not recommended by the manufacturer.
• Neveroperatethisproductifithasadamagedcordorplug,ifitisnotworking
properly, if it has been dropped or damaged, or dropped into water.
• Keepthecordawayfromheatedsurfaces.
• Neveroperatetheproductwiththeairopeningsblocked.Keeptheairopeningsfreeof
lint, hair, and the like.
• Neverdroporinsertanyobjectintoanyopening.
• Donotoperatewhereaerosol(spray)productsarebeingusedorwhereoxygenis
being administered.
• Donotruncordundercarpeting.Donotcoverwiththrowrugs,runnersorsimilar
coverings. Arrange cord away from traffic area and where it will not be tripped over.
WARNING
This is the closed position. Open Air Release Valve. Close Valve Using 2 Thumbs.
INFLATE
DEFLATE
ADJUST

CArE AND MAINTENANCE
WARNING: Do not attempt to disassemble, repair, or service the pump. No serviceable
parts are contained inside. Contact The Coleman Company, Inc. at 3600 North
Hydraulic, Wichita, KS 67219 U.S.A. 1-800-835-3278 or TDD 1-316-832-8707 in the
United States or Sunbeam Corporation (Canada) Limited, DBA Jarden Consumer
Solutions at 20B Hereford Street, Brampton ON L6Y 0M1, 1-800-387-6161 in Canada
for repair and service center information.
1. Inspect your bed prior to each use.
2. Keep your bed away from any sharp objects. Large cuts or snags may not be repairable
and will not be covered by your warranty.
3. When not in use, store your bed in a clean, dry place out of extreme temperatures. Product
must be at room temperature.
4. Do not store your bed folded inside sofa beds or roll-aways. This may cause damage to
your bed and will void your warranty.
CLEANINg
DANGER: To reduce risk of electric shock:
Always unplug this furnishing from the electrical outlet before cleaning or servicing.
We recommend that you do not let the plush surface of your AeroBed®mattress get wet.
Repeated exposure to water or other liquids may cause damage to the plush surface that will
not be covered by your warranty. Should liquid come in contact with the plush surface, blot
liquid dry and use a damp cloth to remove any stain. Let surface air dry completely.
You may clean the PVC on the sides and bottom of your bed with a mild dishwashing
detergent or household cleaner. Do not use strong chemicals or other compounds. Allow your
bed to air dry completely after cleaning and before storing.
Mattress Cover (if included)
Machine wash separately in warm water, gentle cycle using mild soap or detergent. Do not
bleach.
Tumble dry with low heat, remove immediately after drying. Use cool iron if needed.
LIMITED EXPrESS WArrANTY
The Coleman Company, Inc. (“us”) warrants to the original purchaser (“you”) that this
AeroBed®(“product”) is guaranteed against defects in materials and workmanship for the
following periods: pump and valve, three (3) years from date of purchase; mattress, one (1)
year from date of purchase.
OUR EXCLUSIVE OBLIGATION, AND YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED
WARRANTY OR OTHERWISE SHALL BE THE REPAIR OR REPLACEMENT OF ANY PRODUCT OR
PARTS WHICH MAY PROVE DEFECTIVE UNDER THE CONDITIONS OF NORMAL USE DURING
THE WARRANTY PERIOD. IN THE EVENT THE PRODUCT OR PARTS CANNOT BE REPAIRED OR
REPLACED, YOU SHALL RECEIVE A PRODUCT OF COMPARABLE VALUE AT OUR EXPENSE. THIS
WARRANTY IS NON-TRANSFERABLE, AND IS VALID FOR THE FIRST, ORIGINAL PURCHASER
FROM AN AUTHORIZED DEALER OF AEROBED®PRODUCT. THIS LIMITED WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
EXCLUSIONS
Our obligation under this limited express warranty shall not apply if our inspection shows:
A. That the product has been used for other than normal indoor sleeping purposes.
B. Any product or part has been damaged by alteration.
C. Any product or part has been subject to accident, misuse, abuse or has been operated
contrary to our written instructions.
WArrANTY rEDEMPTIONS
You must obtain an authorization from us before returning a defective product. Call us at
1-800-835-3278 or TDD 1-316-832-8707 in the United States or 1-800-387-6161 in Canada
for a return authorization. The product should be carefully packaged and delivered postage or
delivery charges prepaid at the address set forth above. You are responsible for all damages
incurred in shipping.
WArrANTY DISCLAIMEr
EXCEPT FOR THE LIMITED EXPRESS WARRANTY SET FORTH IN THIS SECTION AND IMPLIED
WARRANTIES FOR THE DURATION OF THE EXPRESS WARRANTY, SELLER MAKES NO EXPRESS
OR IMPLIED REPRESENTATIONS. ALL CLAIMS AGAINST US MUST BE BROUGHT WITHIN ONE
(1) YEAR FROM THE TIME THEY ARISE. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW
LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE DISCLAIMER MAY NOT APPLY TO YOU.
LIMITATION OF LIABILITY
TO THE FULLEST EXTENT PERMITTED BY LAW, SELLER SHALL NOT BE LIABLE FOR INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES WITH RESPECT TO THE SALE OF USE
OF THE PRODUCTS, INCLUDING ANY LOST REVENUES, LOSS OF USE OR LOST PROFITS,
REGARDLESS OF THE THEORY BY WHICH ANY CLAIM MAY BE BASED, INCLUDING ANY TORT,
TANGIBLE PROPERTY DAMAGE OR STATUTORY CAUSES OF ACTION. NOTWITHSTANDING
THE TERM OF ANY LIMITED OR IMPLIED WARRANTY, OR IN THE EVENT THAT ANY LIMITED
WARRANTY FAILS OF ITS ESSENTIAL PURPOSE, IN NO EVENT WILL OUR ENTIRE LIABILITY TO
YOU EXCEED THE PURCHASE PRICE ACTUALLY PAID BY YOU FOR THE PRODUCTS, OR ANY
DEFECTIVE OR NONCONFORMING PORTION THEREOF, WHICHEVER IS THE LESSER AMOUNT.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO
YOU.
THIS AGREEMENT AND ANY CLAIMS AND DISPUTES BETWEEN THE PARTIES SHALL BE
GOVERNED BY AND SUBJECT TO THE INTERNAL LAWS (EXCLUSIVE OF THE CONFLICTS OF
LAW PROVISION) AND DECISIONS OF THE COURTS OF THE STATE OF KANSAS. THE EXCLUSIVE
VENUE AND JURISDICTION FOR ALL CLAIMS AND DISPUTES SHALL BE THE STATE OR
FEDERAL COURT LOCATED IN WICHITA, KANSAS.
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003 (B).
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier: R111 USB
Responsible Party - U.S. Contact Information
The Coleman Company, Inc
3600 N Hydraulic
Wichita, KS 67219
1-800-835-3278
www.coleman.com
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Please write us or call us with any comments or questions:
For products purchased in the United States: The Coleman Company, Inc. at 3600 North
Hydraulic, Wichita, KS 67219 U.S.A. 1-800-835-3278 or TDD 1-316-832-8707
For products purchased in Canada: Sunbeam Corporation (Canada) Limited, DBA Jarden
Consumer Solutions at 20B Hereford Street, Brampton ON L6Y 0M1, 1-800-387-6161
The Coleman Company, Inc. neither assumes nor authorizes any representative or other
person to assume any obligation or liability other than those expressly set forth herein.
© 2020 The Coleman Company, Inc. All rights reserved.
Made in China
www.aerobed.com
4010053849 (ECN20071854-03)
Not suitable for
children under
3 years of age.
This furnishing has not been evaluated for flammability or cigarette ignition
resistance. See instructions for additional warnings.
This airbed can melt or burn. Keep away from open flames, heaters, and
other hot objects. Do not smoke on or near the airbed.
This airbed is not for use in water. It is not a life saving device, personal
flotation device, or water toy.
This airbed is not a toy. Do not stand, walk, jump or play on the
airbed. This can result in serious injury or damage to the airbed.
WARNING: Read airbed instruction manual and follow
all safety instructions to avoid serious injury or death.
Risk of Suffocation
• Infantshavesuffocatedoninatablemattresses.Neverallow
a child under 3 years of age or persons with limited mobility
to sleep on an inflatable mattress.
• Childrencanbeentrappedbetweentheinatablemattress
and an adjacent vertical surface. Provide at least a shoulder
width space between the inflatable mattress and walls,
dressers or other vertical objects to avoid entrapment.
• Alwayskeeptheinatablemattressfullyinatedwheninuse.