Aeroex Technologies ROX-400 Supplement

1
Rev 7-02/19
AEROEX Technologies Inc.
Oil Mist Eliminator
ROX-400/600/800/1100/2000
Installation & Service Manual
www.aeroex.com
AEROEX Technologies Inc.
17 Hamilton Rd
Barrie, ON Canada, L4N 8Y6
Tel: [phone] Fax [phone]
705-734-0199
[e-mail]
[e-mail]

Rev 7-02/19 www.aeroex.com orde[email protected] 2
Installation:
•Mount mist collector level.
•Units can be mounted directly on top of machines, on a post or on the wall.
•Ensure that there is 20” free space above to open lid and remove filters.
•Minimize the length of ducting to avoid air flow loses.
•Metal ducting or flexible hose can be used.
•Do not locate suction intake on machining applications in direct line of the cutting spray.
•A chip strainer mounted in the machine (CNC) enclosure is recommended.
•Connect the 2 oil drain lines using a pee trap (5”) or loop in hose.
•Loop in hose must be minimum 8” below connection, no max.
•Connect into 1 hose after pee traps.
•Fill pee traps with water or oil to create air lock.
•Install motor starter and set overloads.
•Connect electrical power to motor using a flexible cable.
•Check motor rotation.
Typical installation:

Rev 7-02/19 www.aeroex.com orde[email protected] 3
Maintenance:
The mist collector can operate for long periods without maintenance. The maintenance period will depend on the
type of oil & solids/chips in air stream. Some soluble oil & synthetic concentrates will congeal requiring the
mechanical separator elements and agglomerator filter media to be manually cleaned/washed. The air flow will
reduce if this happens.
Inspect the unit after 3 months, 6 months & 1 year to establish the maintenance interval. If there is no fouling, the
mist separator can run indefinitely without maintenance. It is recommended that the 2nd stage agglomerator filter
media be replaced every 10 years.
HEPA filter replacement:
Replace when magnehelic pressure gauge
reaches 3” wg
Note:
If 2nd stage filter is plugged, no air flow will be go
to 3rd stage filter and pressure reading will be
low.

Rev 7-02/19 www.aeroex.com orde[email protected] 4
Disassembly:
Disconnect and lock-out electrical
power.
Remove bolts (4) on hinged lid.
Lid jack nut.
Insert 3/8” bolt and jack lid up to open.
Remove the bolts on impeller inlet
plate and remove.
Remove nut on pressure plate and
remove.
Remove 1st stage mechanical
separation elements.
They can be disassembled for
cleaning by removal of the bolts (6).
Remove 2nd stage filter media
(agglomerator). This is a permanent
media and can be washed many
times.

Rev 7-02/19 www.aeroex.com orde[email protected] 5
On models prior to Jan 2013
Replace bottom foam gasket each
time HEPA filter is changed.
Check oil drain line, clean if
necessary.
To remove to remove 3rd stage filter
(HEPA), loosen straps.

Rev 7-02/19 www.aeroex.com orde[email protected] 6
Filter Options
ROX-400 / 600
Item
Description
Part #
Qty
1
1st Stage Mechanical Element
ROX-400 / 600
600ME-002
1
2
2nd Stage Agglomerator Filter
ROX-400 / 600
Coolant
600AF-012
1
3
2nd stage agglomerator filter,
for used with filter ring
ROX-400 / 600
Use on sticky or high solids coolant applications
Use on oil applications
600AF-2010
1
4
(a)
(b)
2nd stage agglomerator filter ring
ROX-400 / 600 filter ring, coolant
ROX-400 / 600 filter ring, oil
600FR-2204
600FR-2206
1
1
5
Pressure Plate for Filter Ring
One time purchase when converting to filter ring.
600PP-2002
1
6
(a)
(b)
(c)
(d)
3rd stage HEPA filter
95% @ 0.3 µm, prior to 2015
95% @ 0.3 µm, after Jan 2015
99.97% @ 0.3 µm, prior to 2015
99.97% @ 0.3 µm, after Jan 2015
Check part# before ordering
600HF-095
600HF2095
600HF-099
600HF2099
1
1
1
1

Rev 7-02/19 www.aeroex.com orde[email protected] 7
ROX-800 / 1100
Item
Description
Part #
Qty
1
1st Stage Mechanical Element
ROX-800 / 1100
1100ME-002
1
2
2nd Stage Agglomerator Filter
ROX-800 / 1100
Coolant
1100AF-012
1
3
2nd stage agglomerator filter,
for used with filter ring
ROX-800 / 1100
Use on sticky or high solids coolant applications
Use on oil applications
1100AF-2010
1
4
(a)
(b)
2nd stage agglomerator filter ring
ROX-800 / 1100 filter ring, coolant
ROX-800 / 1100 filter ring, oil
1100FR-2204
1100FR-2206
1
1
5
Pressure Plate for Filter Ring
One time purchase when converting to filter ring.
1100PP-2002
1
6
(a)
(b)
(c)
(d)
3rd stage HEPA filter
95% @ 0.3 µm, prior to 2015
95% @ 0.3 µm, after Jan 2015
99.97% @ 0.3 µm, prior to 2015
99.97% @ 0.3 µm, after Jan 2015
Check part# before ordering
2000HF-095
2000HF2095
2000HF-099
2000HF2099
1
1
1
1

Rev 7-02/19 www.aeroex.com orde[email protected] 8
ROX-2000
Item
Description
Part #
Qty
1
1st Stage Mechanical Element
ROX-2000
2000ME-002
1
2
2nd Stage Agglomerator Filter
ROX-2000
Coolant
2000AF-012
1
4
2nd stage agglomerator filter,
for used with filter ring
ROX-2000
Use on sticky or high solids coolant applications
Use on oil applications
2000AF-2010
1
5
(a)
(b)
2nd stage agglomerator filter ring
ROX-2000 filter ring, coolant
ROX-2000 filter ring, oil
2000FR-2204
2000FR-2206
1
1
Pressure Plate for Filter Ring
One time purchase when converting to filter ring.
2000PP-2002
1
6
(a)
(b)
(c)
(d)
3rd stage HEPA filter
95% @ 0.3 µm, prior to 2015
95% @ 0.3 µm, after Jan 2015
99.97% @ 0.3 µm, prior to 2015
99.97% @ 0.3 µm, after Jan 2015
Note: 2 HEPA filters per unit.
Check part# before ordering
2000HF-095
2000HF2095
2000HF-099
2000HF2099
2
2
2
2