AES 7007 User manual

AES Corporation To view the complete Installation Manual refer to website: http://aes-corp.com 40-7007-QSG Rev 5
Out of the Box
7007 Burg Subscriber
Quick Start Guide - Part# 40-7007-QSG
7094A IntelliPro (if equipped)
Overview
The 7007 Subscriber Unit is an AES-IntelliNet RF Communicator
used to link an alarm panel to an alarm monitoring central
station. The unit is UL-approved for commercial alarm
monitoring. The system is designed for use with the
AES-IntelliNet system for alarm, supervisory, and trouble
messages to be transmitted to the system central receiver.
Installation, Configuration and Programming
See these resources for detailed information about installing,
configuring, and programming the 7007:
AES 7007 RF Subscriber Installation, Operation &
Programming Manual (Part# 40-7007)
AES 7094A IntelliPro Installation, Operation & Programming
Manual (Part# 40-7094A)
Important!The AES 7041E Hand-Held Programmer
cannot program the 7007 Subscriber.
Connect to 7007
1
A web browser enabled device using an Ethernet or Wi-Fi
connection must be used to configure the 7007.
Ethernet Connection: Connect an Ethernet cable to the 7007
and the other end directly into a PC/Laptop or router. Enter
the IP address displayed on the 7007 LCD on the web browser
of your PC/Laptop, and log in with credentials admin/admin
for username/password.
Wi-Fi Connection: Plug an approved Wi-Fi module into one of
the 7007 USB ports. On your Wi-Fi device, connect to SSID
“AES2.0-XXX” using password “7007burg” where XXX are the
last 3 digits of the serial number of the 7007. The Captive
Portal will automatically redirect to the web browser login
screen where you can log in with credentials admin/admin for
username/password. Alternatively, you can also enter the IP
address displayed on the 7007 LCD on the web browser of
Wi-Fi smartphone or tablet.
Set ID and Cipher Code
2
1. Navigate to the Configuration tab. Under the Subscriber ID
panel, enter a unique hex (0001-FFFF) Subscriber ID and
click on Save Change.
2. Under the Radio Configuration panel, enter the Cipher
Code and click on Save Change.
Note: You will need to have the system cipher code for the
subscriber to enroll in the network. The Subscriber ID must
be unique from any other subscriber on the network.
Set Zone Inputs
3
1. Navigate to the Accessories tab. Under the Zones panel set
the input types. If any of the 4 zones have a fire input, set
Fire Zones to Yes.
2. To allow consecutive Alarm-Trouble-Alarm reporting, set
Consecutive AT events to Yes (default is No)
3. Set the zone input to either Normally Open, Normally
Closed, Inverted or Fire/Supervised (if Fire Zones is No).
4. Set zone input restoral to either Yes or No for each zone.
5. Repeat these steps for the remaining 3 zone inputs and
click on Save Change.
Note: Zone 5 and 6 are the Bell Output (Siren) zones and
are programmed differently.
Important! Set unused zone inputs to Bypass.
Set Flexible Power Options
4
Navigate to the Configuration tab. Under the Flexible Power
Option panel, select the power option that matches the
subscriber installation and click on Save Change.
Apply the settings
5
Click on the Update button to apply all the settings you saved.
Disconnect from 7007
6
After configuring the 7007, remove the Ethernet cable and/or
the W-Fi module from the 7007.
Reset to Default Configuration
Navigate to the System tab. Under the Reset to Default
Configuration panel, select the components to reset to factory
configuration and click on Reset Configuration.
LIMITED PRODUCT WARRANTY:
AES warrants to the original purchaser that the AES Subscriber
Unit will be free from defects in material and workmanship
under normal use and service for three (3) years from the date
of original purchaser’s purchase. Except as required by law, this
Limited Warranty is only made to the original purchaser and
may not be transferred to any third party.
This Limited Product Warranty is made in lieu of any other
warranties, expressed or implied, it being understood that all
other warranties, expressed or implied, including of
merchantability or fitness for a particular purpose, are hereby
expressly excluded. AES assumes no liability for any personal
Quick Start Guide
AES Model 7007 Security Subscriber
Page 1 of 1

AES Corporation To view the complete Installation Manual refer to website: http://aes-corp.com 40-7007-QSG Rev 5
injury, property damage, consequential damages, or any other
loss or damage due, among other things, to this product’s
failure to operate or provide adequate warning. AES’s sole
responsibility is to repair or replace, at AES’s sole option, the
AES product that is judged defected by AES during the limited
warranty period under the terms of its Limited Warranty.