Aesculap FavoritaCL/Libra User manual

Aesculap Suhl GmbH
FavoritaCL/Libra
Instructions for use/Technical description
Battery-powered clipping machine
FavoritaCL/Libra
Gebrauchsanweisung/Technische Be-
schreibung
Akku-Schermaschine FavoritaCL/Libra
Mode d’emploi/Description technique
Tondeuse à accu FavoritaCL/Libra
Instrucciones de manejo/Descripción téc-
nica
Esquiladora a batería FavoritaCL/Libra
Istruzioni per l’uso/Descrizione tecnica
Tosatrice ad accumulatore FavoritaCL/Libra
Gebruiksaanwijzing/Technische Beschrij-
ving
Accu-scheermachine FavoritaCL/Libra
Bruksanvisning/Teknisk Beskrivning
Gerätebez-Titel
Инструкция по примению/
Техническое описание
Машинка для стрижки, с аккумулятором,
FavoritaCL/Libra
Instrukcja u¿ytkowania/Opis Techniczny
Akumulatorowa maszynka do strzy¿enia
FavoritaCL/Libra
使用说明书／技术描述
FavoritaCL/Libra 蓄电池剪毛机
取扱説明書／技術仕様書
充電池駆動ヘアカッター FavoritaCL/Libra
사용 설명서 /기술 설명
FavoritaCL/Libra 충전 면도기

2
3
4
2
1
3
5
6
789
10
11
12

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
2
Legend
1Blade adapter
2Lever
3Battery-powered clipping machine FavoritaCL/Libra
4Battery release lock
5Charger
6Mains power cord (with device plug)
7Charging bay (for Li-ion battery)
8Charge state indicator (for Li-ion battery)
9Li-ion battery
10 Charge state indicator (for battery-powered
clipping machine FavoritaCL/Libra)
11 Charging bay (for battery-powered clipping
machine FavoritaCL/Libra)
12 On/Off switch
13 Screw to fix casing
14 Pressure piece
15 Knurled screw
16 Leaf spring
17 Serration
18 Lower cutting plate
19 Upper cutting plate
Symbols on product
Contents
1. Safe handling ........................................................... 3
2. Product description ................................................ 3
2.1 System components ............................................... 3
2.2 Components necessary for use ........................... 4
2.3 Intended use of battery-powered clipping
machine FavoritaCL/Libra ...................................... 4
2.4 Intended use of charger GT203/Li-ion
battery GT201 .......................................................... 4
2.5 Operating principle of battery-powered
clipping machine FavoritaCL/Libra ..................... 4
2.6 Operating principle of charger GT203/Li-ion
battery GT201 .......................................................... 4
2.6.1 Charging principle .................................................. 4
2.6.2 Charging time .......................................................... 4
3. Preparation and setup ........................................... 5
4. Working with the battery-powered clipping
machine FavoritaCL/Libra and charger
GT203/Li-ion battery GT201 ................................ 5
4.1 System set-up .......................................................... 5
4.1.1 Connecting the accessories.................................. 5
4.1.2 Attaching the Blade ............................................... 5
4.1.3 Connecting the charger/Charging the Li-ion
battery........................................................................ 6
4.2 Function checks of battery-powered clipping
machine FavoritaCL/Libra ...................................... 6
4.3 Function checks of the charger .......................... 7
4.4 Safe handling: Blade .............................................. 7
4.4.1 Adjusting the plate pressure................................ 7
4.4.2 Sharpening the cutting plate .............................. 7
4.4.3 Removing the blade ............................................... 7
4.4.4 Lubricating the blade............................................. 7
4.4.5 Changing the Li-ion battery ................................ 8
5. Processing ................................................................. 8
5.1 Cleaning/Disinfecting ............................................ 8
5.2 Control, care and inspection ............................... 9
6. Maintenance ..........................................................10
7. Troubleshooting list .............................................11
7.1 Battery-powered clipping machine
FavoritaCL/Libra .....................................................11
7.2 Charger and Li-ion battery ................................11
8. Technical Service ..................................................13
9. Accessories/Spare parts ......................................14
Adhere to instructions for use
Labeling of electric and
electronic devices according to
directive 2012/19/EU (WEEE),
see Chapter Disposal

3
10. Technical specifications ......................................15
10.1 Battery-powered clipping machine
FavoritaCL/Libra .....................................................15
10.2 Charger ....................................................................15
10.3 Li-ion battery .........................................................15
10.4 Declaration of conformity ..................................15
11. Disposal ....................................................................15
11.1 For EU countries only ...........................................16
11.2 Li-ion batteries ......................................................16
12. 2 Years warranty ...................................................16
13. Distributor in the US/Contact in Canada for
product information and complaints ..............17
1. Safe handling
CAUTION (for US users only)
Federal law restricts this device for sale by or on
order of a physician!
¾Prior to use, check for proper condition and
functioning of the product.
¾Store the charger and Li-ion batteries at room
temperature.
¾Keep dry the charger and Li-ion batteries.
¾Charge the Li-ion batteries prior to first use.
¾Observe our “Notes on Electromagnetic
Compatibility (EMC)“.
¾To prevent damage caused by improper setup or
operation, and in order not to compromise
warranty and manufacturer liability:
– Use the product only according to these
instructions for use.
– Observe all safety information and maintenance
advisories.
– Ensure the manufacturer’s approval before using
accessories that are not mentioned in the
instructions for use.
¾Ensure that the product and its accessories are
operated and used only by persons with the
requisite training, knowledge or experience.
¾Keep the instructions for use accessible for the
user.
¾Always adhere to applicable standards.
¾Ensure that the electrical facilities in the room in
which the device is being used conform to
IEC norms.
¾Unplug the device by pulling the plug, but never by
pulling the power cord.
¾Do not operate the product in explosion-hazard
areas.
¾Do not use the product if it is damaged or
defective. Set aside the product if it is damaged.
Note
The device can be used by children over the age of 8 as
well as by persons with reduced physical, sensory or
mental capacities or with lack of experience and
knowledge, if these persons are supervised or have been
instructed on how to use the device safely, and if they
understand the risks associated with the use of the
device.
¾Do not allow children to play with the device.
¾Do not allow children to carry out cleaning and
maintenance of the device without supervision.
DANGER
Risk of death by electric shock!
¾Do not open the product (except
for changing a charging bay).
¾Only ever connect the product
to power mains with equipment
grounding conductor.

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
4
2. Product description
2.1 System components
Note
The battery-powered clipping machine FavoritaCL/Libra
supplied without any blade. Instead, there is a range of
blades available for various applications!
2.2 Components necessary for use
• Battery-powered clipping machine FavoritaCL/Libra
•Blade
•Charger
• Mains power cord (with device plug)
• Li-ion battery
2.3 Intended use of battery-powered
clipping machine FavoritaCL/Libra
Note
The device is intended exclusively for cutting animal
hair.
The battery-powered clipping machine FavoritaCL/
Libra is used for clipping small animals.
The battery-powered clipping machine FavoritaCL/
Libra must be used with a blade appropriate for the
respective application.
2.4 Intended use of charger GT203/
Li-ion battery GT201
The charger GT203 is used for charging the battery-
powered clipping machine FavoritaCL/Libra and the Li-
ion battery. There is one charging bay each for the two
components.
2.5 Operating principle of battery-
powered clipping machine
FavoritaCL/Libra
The battery-powered clipping machine FavoritaCL/Libra
is switched on and off by sliding the On/Off switch up or
down, respectively.
Designation Art. no.
Battery-powered
clipping machine
FavoritaCL
GT200
Battery-powered clip-
ping machine Libra
GT210
Li-ion battery GT201
Charger GT203
Mains power cord (with
device plug)
see Chapter Accessories/
Spare parts
Instructions for use TA012167

5
2.6 Operating principle of charger
GT203/Li-ion battery GT201
The charger GT203 is designed for the mains voltage/
frequency range 100 V to 240 V / 50 Hz to 60 Hz.
To make the charger GT203 ready for operation,
connect it to mains power by plugging in the mains
plug.
The charger GT203 is equipped with to charging bays.
The first charging bay is for charging the battery-
powered clipping machine FavoritaCL/Libra, while in
the second charging bay the Li-ion battery is charged.
Each charging bay has an indicator field on the charger
front panel assigned to it.
Charging starts automatically, as soon as a Li-ion
battery is inserted in the charging station.
The charging time in the charging bays depends on the
charge state and capacity of the Li-ion batteries.
2.6.1 Charging principle
The Li-ion batteries are charged by constant current
pulses.
The charge state of the Li-ion battery is monitored
during charging. Monitoring of the charging curve
ensures that the battery is fully charged without
overcharging.
Additionally, the battery temperature and charging
time are monitored as well.
The charger monitors the battery status and indicates
the charge state via two LED indicators.
LED indicators:
• green = Battery fully charged
• red = Battery completely discharged
2.6.2 Charging time
Charging is stopped as soon as the maximum charging
time is reached.
The charging time is approx. 50 min.
3. Preparation and setup
Non-compliance with these rules will result in
complete exclusion of liability on the part of Aesculap.
¾When setting up and operating the product, always
observe:
– national regulations for installation and
operation,
– national regulations on fire and explosion
protection.
– operating advisories according to IEC-/VDE
regulations.
DANGER
Fire and explosion hazard!
¾Do not operate the product in
explosion-hazard areas.
CAUTION
Malfunction of, or damage to the
product caused by improper setup!
¾Do not expose the product to
direct sunlight or moisture.
¾Do not cover the ventilation
slots of the product.
¾Connect the product to the
specified voltage of 100 V to
240 V/50 Hz to 60 Hz.
¾Ensure that the mains power
socket used for supplying the
product is freely accessible.

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
6
4. Working with the battery-
powered clipping machine
FavoritaCL/Libra and charger
GT203/Li-ion battery GT201
4.1 System set-up
4.1.1 Connecting the accessories
Combinations of accessories that are not mentioned in
the present instructions for use may only be employed
if they are specifically intended for the respective
application, and if they do not compromise the
performance and safety characteristics of the
products.
¾Please contact your B. Braun/Aesculap Partner or
Aesculap Technical Service (address: see Chapter
Technical Service) with any inquiries in this
respect.
4.1.2 Attaching the Blade
Note
The battery-powered clipping machine FavoritaCL/Libra
ships without any blade. Instead, there is a range of
blades available for various applications!
¾Slide On/Off switch 12 upward to switch on
battery-powered clipping machine FavoritaCL/
Libra 3.
¾Push lever 2towards the shell of the product.
¾Mount the blade on blade adapter 1.
¾Release lever 2.
This completes the mounting of the blade.
4.1.3 Connecting the charger/Charging the
Li-ion battery
Note
Prior to battery loading, switch off the battery-powered
clipping machine FavoritaCL/Libra!
Note
Li-ion batteries heat up slightly during charging.
WARNING
Risk of injury caused by sharp cut-
ting plates!
¾Apply proper care when handling
and operating the blade of bat-
tery-powered clipping machine
FavoritaCL/Libra.
WARNING
Fire hazard due to battery poles
shorted by fluids or metal compo-
nents!
¾Do not short the Li-ion battery.
WARNING
Risk of injury and material damage
due to damaged Li-ion batteries!
¾Prior to charging, check the Li-
ion batteries for any damage.
¾Do not use or charge damaged
Li-ion batteries.
CAUTION
Loss of capacity/performance due
to prolonged storage of discharged
Li-ion batteries!
¾Store Li-ion batteries only in
fully charged condition and
recharge stored batteries once
every month.
CAUTION
Destruction of the product,
charging bay or Li-ion battery when
inserting the wrong type of battery
in the charging bay!
¾Insert Li-ion batteries only in
the appropriate charging bay.
¾Insert the Li-ion battery in the
correct position.

7
Note
Unplug the mains power cord at the mains socket when
the charger is not going to be used!
¾To connect charger 5: Plug in the device plug of
mains power cord 6in charger 5.
¾Plug in the mains plug of mains power cord 6at
the mains power socket.
¾Insert Li-ion battery 9in charging bay 7of
charger 5and charge the battery.
- or -
¾Insert battery-powered clipping machine FavoritaCL/
Libra 3in charging bay 11 of charger 5and charge
the machine.
Charge state indicator 8or charge state
indicator 10 lights up red.
After charging, the charge state indicator 8/10
shines green and battery-powered clipping
machine FavoritaCL/Libra 3/Li-ion battery 9is
ready for operation.
4.2 Function checks of battery-
powered clipping machine
FavoritaCL/Libra
¾Carry out a visual inspection.
¾Check the switch position.
¾Install the battery, see Chapter Changing the Li-ion
battery.
¾Mount the blade correctly and lubricate it if
necessary, see Chapter Safe handling: Blade.
¾Keep a charged Li-ion battery on hand, as reserve.
¾Clean the battery-powered clipping machine
FavoritaCL/Libra prior to use, see Chapter Cleaning/
Disinfecting.
4.3 Function checks of the charger
¾Carry out a visual inspection.
Prior to connecting the product to mains power:
– Check mains power cord 6for possible damage.
– Check the product for any damage (e.g. bent
contacts of the charging bays).
¾Plug in mains power cord 6at the device socket of
the charging station.
¾Plug in the mains plug at the mains power socket.
¾Insert Li-ion battery 9in charging bay 7of
charger 5and charge the battery.
- or -
¾Insert the battery-powered clipping machine
FavoritaCL/Libra 3in charging bay 11 of charger 5
and charge the machine.
Charge state indicator 8or charge state
indicator 10 lights up red.
After charging, the charge state indicator 8/10
shines green and the battery-powered clipping
machine FavoritaCL/Libra 3/Li-ion battery 9is
ready for operation.
The product is ready for operation.

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
8
4.4 Safe handling: Blade
4.4.1 Adjusting the plate pressure
Note
The plate pressure can be adjusted to increase the
cutting power as required (see foldout page)!
¾Tighten knurled screw 15 so that upper cutting
plate 19 can be moved by hand, by applying
moderate, lateral pressure.
4.4.2 Sharpening the cutting plate
Note
For sharpening the cutting plate, please contact
Technical Service, see Chapter Technical Service.
4.4.3 Removing the blade
¾Loosen knurled screw 15 with leaf spring 16.
¾Push upper cutting plate 19 under pressure
piece 14 out of the blade.
This completes the disassembly of the blade.
4.4.4 Lubricating the blade
¾Disassemble the blade, see Chapter Removing the
blade.
¾Clean upper cutting plate 19 and lower cutting
plate 18 with a soft wipe or brush. Make certain
the gaps in serration 17 are cleaned properly.
¾Slightly lubricate upper cutting plate 19 and lower
cutting plate 18 with special lubricant for blades
GT604.
4.4.5 Changing the Li-ion battery
Fig. 1
¾Hold battery-powered clipping machine
FavoritaCL/Libra 3and press battery release lock 4.
¾Pull out Li-ion battery 9from battery-powered
clipping machine FavoritaCL/Libra 3.
¾Insert the charged Li-ion battery 9in battery-
powered clipping machine FavoritaCL/Libra 3as far
as it will go.
The battery-powered clipping machine FavoritaCL/
Libra 3is ready for operation.
WARNING
Risk of injury caused by sharp
cutting plates!
¾Apply proper care when handling
the blade of battery-powered
clipping machine FavoritaCL/
Libra.
3
9
4

9
5. Processing
5.1 Cleaning/Disinfecting
Note
Always follow disposal and hygiene instructions and
regulations!
Manual cleaning/disinfecting
¾Wipe the shell of the product with a lint-free cloth
moistened with a commercial disinfectant for wipe
disinfection.
¾If necessary, after the appropriate exposure time,
wipe off any residues of the cleaning/disinfecting
agent with a lint-free cloth moistened with clean
water.
¾Dry the product with a clean, lint-free cloth.
¾Clean the contacts in the charging bay with
isopropanol or ethyl alcohol and a cotton swab. Do
not use corrosive chemicals.
¾If necessary, repeat the cleaning/disinfecting
process.
CAUTION
Damage to, or destruction of the
product caused by mechanical
cleaning/disinfecting or steriliza-
tion!
¾Only clean and disinfect the
product manually.
¾Do not sterilize the product
under any circumstances.
DANGER
Risk of electric shock and fire
hazard!
¾Unplug the unit before cleaning.
¾Make certain that no fluids will
penetrate the product.
¾Leave the product exposed to
air for at least 1 minute after
cleaning/disinfecting.
CAUTION
Damage to the product due to
incorrect cleaning or inappropriate
cleaning/disinfecting agents!
¾Use any commercial detergent
for surface cleaning.
¾Never immerse the product in
water or detergent.
¾Do not introduce any fluid into
the charging bays.
¾Clean the contacts in the
charging bays, applying extreme
care.

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
10
5.2 Control, care and inspection
¾Allow the product to cool down to room
temperature.
¾Inspect the product after each cleaning and
disinfecting cycle to be sure it is clean, functional
and undamaged.
¾Lubricate the blade as appropriate, see Chapter
Lubricating the blade.
¾To enhance the cutting power, adjust the plate
pressure as required, see Chapter Adjusting the
plate pressure.
¾Check the product for any damage, a typical
running noise, overheating or excessive vibration.
¾Inspect the blade for broken, damaged or blunt
cutting edges.
¾Set aside the product if it is damaged.
6. Maintenance
To ensure reliable operation, Aesculap recommends
servicing the product at least once a year.
Service addresses
In the UK
KG PRODUCTS
243-251 City Road, Fenton
Stoke-on-Trent, Staffs
ST4 2PX
United Kingdom,
Phone (44) - 01782 844 866
DIAMOND EDGE
126 Gloucester Rd.
Brighton, BN1 4BU.
United Kingdom
Phone (44) - 01273 605 922
Or in the US
A & J Sales and Service
42 - A Frame Drive
West Burke, VT 05871
USA
Phone: [phone]
Or in Germany
Albert Kerbl GmbH
Felizenzell 9
84428 Buchbach / Germany
Phone: [phone]
Fax: [phone]
E-Mail: [e-mail]
www.kerbl.com
Other service addresses can be obtained from the
address indicated above.

11
7. Troubleshooting list
7.1 Battery-powered clipping machine FavoritaCL/Libra
7.2 Charger and Li-ion battery
Malfunction Finding Cause Remedy
Battery-powered
clipping machine
FavoritaCL/Libra not
starting up
Check switch position Li-ion battery not
charged
Charge the Li-ion battery
– Li-ion battery defective Insert new Li-ion battery
– No Li-ion battery inserted Insert new Li-ion battery
Battery-powered
clipping machine
FavoritaCL/Libra stops
running
– Li-ion battery deactivated
by protective circuit
Switch the machine off and
on again
– Li-ion battery fully
discharged
Insert new Li-ion battery
Battery-powered
clipping machine
FavoritaCL/Libra not
charged in the charging
station
LED indicators remain
dark
– see Chapter Charger and Li-
ion battery
Malfunction Finding Cause Remedy
Charger not functioning LED indicators remain
dark
Power cord not plugged
in
Plug in mains power cord
in device socket at the
charger and in a mains
power socket
Li-ion battery not
charged
Mains power cord
defective
Replace mains power
cord
Charger defective Have the product
repaired by the
manufacturer

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
12
Li-ion battery not charged Li-ion battery inserted
properly, charge state
indicator remains dark
Charger contacts dirty or
damaged
Clean the contacts in the
charging bay, see
Chapter Cleaning/
Disinfecting, or have the
charger repaired by the
manufacturer
Li-ion battery defective Have the Li-ion battery
repaired by the
manufacturer
Charger defective Have the charger
repaired by the
manufacturer
Excessive temperature in
the Li-ion battery
detected during charging
Remove the Li-ion
battery from the
charging bay, let it cool
down and restart
charging.
If the malfunction recurs,
have battery repaired by
the manufacturer
Charging malfunction or
Li-ion battery defective
Remove the Li-ion
battery from the
charging bay and repeat
charging, if necessary in
another charging bay.
If the malfunction recurs,
have the Li-ion battery
repaired by the
manufacturer
Malfunction Finding Cause Remedy

13
8. Technical Service
Modifications carried out on medical technical
equipment may result in loss of guarantee/warranty
rights and forfeiture of applicable licenses.
Service addresses
In the UK
KG PRODUCTS
243-251 City Road, Fenton
Stoke-on-Trent, Staffs
ST4 2PX
United Kingdom,
Phone (44) - 01782 844 866
DIAMOND EDGE
126 Gloucester Rd.
Brighton, BN1 4BU.
United Kingdom
Phone (44) - 01273 605 922
Or in the US
A & J Sales and Service
42 - A Frame Drive
West Burke, VT 05871
USA
Phone: [phone]
Or in Germany
Albert Kerbl GmbH
Felizenzell 9
84428 Buchbach / Germany
Phone: [phone]
Fax: [phone]
E-Mail: [e-mail]
www.kerbl.com
Other service addresses can be obtained from the
address indicated above.

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
14
9. Accessories/Spare parts
Art. no. Version Power cord Li-ion
battery
Charging
station
Battery-
powered
clipping
machine
Accessories
GT206 Europe
except UK
TA012170
Europe flat
connector,
black, L=1.8 m
GT201 GT200880 GT200
unpacked
GT604800
Hand oiler
GT206G UK TA012169
UK plug,
black, L=1.8 m
GT201 GT200880 GT200
unpacked
GT604800
Hand oiler
GT206J Japan,
Mexico
110–125 V
TA012168
2-pole device
plug, black,
L=1.8 m
GT201 GT200880 GT200
unpacked
GT604800
Hand oiler
GT206K USA TA012168
2-pole device
plug, black,
L=1.8 m
GT201 GT200880 GT200
unpacked
GT604800
Hand oiler
GT206AR Argentina TA012333 GT201 GT200880 GT200
unpacked
GT604800
Hand oiler
GT216 Europe
except UK
TA012170
Europe flat
connector,
black, L=1.8 m
GT201 GT200880 GT210
unpacked
GT604800
Hand oiler

15
10. Technical specifications
10.1 Battery-powered clipping machine
FavoritaCL/Libra
10.2 Charger
10.3 Li-ion battery
10.4 Declaration of conformity
Model GT216
Stroke rate 2 300 1/min
Charging/Output
voltage
max. 8.4 V
Charging/Output
current
max. 1.2 A
Weight
(without blade)
400 g
Classification acc. to
Directive 93/42/EEC
II
EN 60335-1, EN 60335-2-29
Model GT203
Mains voltage ranges
(Current intake)
100-240 V
AC frequency 50-60 Hz
Charging/Output
voltage
max. 8.4 V
Charging/Output
current
max. 1.2 A
Weight 495 g
Classification acc. to
Directive 93/42/EEC
II
Approval marks CE, UL
Model GT201
Cell type Li
DC voltage 7.4 V
Charge capacity approx. 1.2 Ah
Charging time 50 min ±5 min
We declare under our sole
responsibility that this product
conforms to the following standards or
other normative documents:
2004/108/EC EMC guidelines:
DIN EN 60335-1
DIN EN 60335-2-8
Safety of household and similar
electrical appliances
- general requirements
- for hair clipping machines
Aesculap Suhl GmbH

Aesculap Suhl GmbH
Battery-powered clipping machine FavoritaCL/Libra
16
11. Disposal
Power tools, accessories and packaging should be
recycled through environmentally compatible
processes.
11.1 For EU countries only
11.2 Li-ion batteries
Do not dispose of batteries with household refuse and
do not throw them into fire or water. Defective or
exhausted batteries must be collected and recycled or
disposed of in environmentally compatible ways
according to Directive 2006/66/EC.
12. 2 Year Warranty
Dear Customer,
Thank you for choosing a product from our company.
For decades, the name Aesculap has stood for proven
quality and first-class service. We are known to pro-
vide innovative, high-performance products for our
customers. Aesculap manufactures high-quality
devices, using high-quality materials and careful man-
ufacturing processes. We would like to point out to you
that we are not liable for defects in our products, if
these are caused by improper use, normal wear or are
caused by the product being improperly used or if
inappropriate or not properly functioning third-party
products are used.
Parts that are typically subject to wear, and for which
we are therefore not liable, are the battery and clipper
head. Defects that do not affect or only negligibly
affect the value or function of the product are also
excluded from our warranty.
If we are liable under our warranty, we reserve the
right to repair or replace the product.
Do not dispose of power tools with
household waste!
According to European Directive
2012/19/EU on waste electric and
electronic devices, and its implemen-
tation in national legislation, power
tools that have reached the end of
their service life must be collected
separately and recycled through envi-
ronment-friendly processes.

17
13. Distributor in the US/Contact
in Canada for product infor-
mation and complaints
Aesculap Inc.
3773 Corporate Parkway
Center Valley, PA 18034
USA
Service addresses
A & J Sales and Service
42 - A Frame Drive
West Burke, VT 05871
USA
Phone: [phone]
Or in Germany
Albert Kerbl GmbH
Felizenzell 9
84428 Buchbach / Germany
Phone: [phone]
Fax: [phone]
E-Mail: [e-mail]
www.kerbl.com
Other service addresses can be obtained from the
address indicated above.

Aesculap Suhl GmbH
Akku-Schermaschine FavoritaCL/Libra
18
Legende
1Scherkopfhalter
2Hebel
3Akku-Schermaschine FavoritaCL/Libra
4Akku-Entriegelung
5Ladegerät
6Netzanschlussleitung (mit Gerätestecker)
7Ladeschacht (für Li-Ionen-Akku)
8Ladezustandsanzeige (für Li-Ionen-Akku)
9Li-Ionen-Akku
10 Ladezustandsanzeige (für Akku-Schermaschine
FavoritaCL/Libra)
11 Ladeschacht (für Akku-Schermaschine FavoritaCL/
Libra)
12 Ein-/Ausschalter
13 Zylinderschraube
14 Druckstück
15 Rändelschraube
16 Blattfeder
17 Zähne
18 Untere Schneidplatte
19 Obere Schneidplatte
Symbole am Produkt
Inhaltsverzeichnis
1. Sichere Handhabung ............................................19
2. Gerätebeschreibung .............................................19
2.1 Lieferumfang ..........................................................19
2.2 Zum Betrieb erforderliche Komponenten ......20
2.3 Verwendungszweck
Akku-Schermaschine FavoritaCL/Libra ............20
2.4 Verwendungszweck Ladegerät GT203/
Li-Ionen-Akku GT201 ..........................................20
2.5 Funktionsweise
Akku-Schermaschine FavoritaCL/Libra ............20
2.6 Funktionsweise Ladegerät GT203/
Li-Ionen-Akku GT201 ..........................................20
2.6.1 Ladeprinzip.............................................................. 20
2.6.2 Ladezeit.................................................................... 20
3. Vorbereiten und Aufstellen ................................21
4. Arbeiten mit der Akku-Schermaschine
FavoritaCL/Libra, dem Ladegerät GT203/
Li-Ionen-Akku GT201 ..........................................21
4.1 Bereitstellen ...........................................................21
4.1.1 Zubehör anschließen............................................ 21
4.1.2 Scherkopf aufstecken........................................... 21
4.1.3 Ladegerät anschließen/Li-Ionen-Akku laden..... 22
4.2 Funktionsprüfung
Akku-Schermaschine FavoritaCL/Libra ............22
4.3 Funktionsprüfung Ladegerät .............................23
4.4 Handhabung Scherkopf .......................................23
4.4.1 Plattendruck einstellen........................................ 23
4.4.2 Schneidplatte schleifen....................................... 23
4.4.3 Scherkopf demontieren....................................... 23
4.4.4 Scherkopf ölen....................................................... 23
4.4.5 Li-Ionen-Akku austauschen............................... 24
5. Aufbereitung ..........................................................24
5.1 Reinigung/Desinfektion .......................................24
5.2 Kontrolle, Pflege und Prüfung ...........................25
6. Wartung ..................................................................25
7. Fehler erkennen und beheben ...........................26
7.1 Akku-Schermaschine FavoritaCL/Libra ............26
7.2 Ladegerät und Li-Ionen-Akku ...........................26
8. Technischer Service ..............................................28
9. Zubehör/Ersatzteile ..............................................29
10. Technische Daten ..................................................30
10.1 Akku-Schermaschine FavoritaCL/Libra ............30
Gebrauchsanweisung einhalten
Kennzeichnung von Elektro-
und Elektronikgeräten entspre-
chend Richtlinie 2012/19/EU
(WEEE), siehe Kapitel Entsor-
gung