AFG G611 User manual

3-in-1 Convertible Classic Baby Crib
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts
to the store from where it was purchased before contacting AFG Customer Service.
AFG Customer Service:
E-mail: [e-mail]
Tel: [phone]
Model No.:
G
611/612
PO #:
Serial #:

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 2
WARNING: Failure to follow these warnings and the
assemblyinstructions could result in serious injury or death.
Read all instructions B FOR assembly and US of product. K P IN
STRUCTIONS FOR FUTUR US .
•First remove hardware from box and sort by size. Check to see that all hardware and wooden pieces are
present before assembling.
•Follow instructions listed below in the proper sequence as numbered to assure fast, easy and correct
assembly.
•D N T use this crib if the enclosed or attached instructions cannot be strictly adhered to.
WARNING:
•D N T attempt to repair or modify parts with cracks or defects. Please contact us for immediate
replacement.
•This product is for home use and is not intended for use in schools, day care centers or other
commercial establishments.
•Must be assembled by a capable adult.
•CHOKING HAZARDS: D N T put small / loose components on top of the unit where baby could
reach.
Crib Warning
WARNING : Infants can suffocate on soft bedding. Never add a pillow or
comforter. Never place additional padding under an infant.
•This crib conforms to applicable regulations promulgated by the Consumer Products Safety Commission.
•Never use plastic shipping bags or other plastic film as mattress covers.
•Infants can suffocation in gaps between crib sides and a mattress that is too small.
•To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to sleep,
unless therwise advised by your physician.
•D N T use a water mattress with this crib.
•Do not remove any wood screws in the normal disassembly of the crib.
•Replace teething rail if damaged, cracked or loose.
•If refinishing, use a non−toxic finish specified for children’s products.
•Follow warnings on all products in a crib.
Strangulation Hazard
•Strings can cause strangulation! Do not place items with a string around a child’s neck, such as hood strings
or pacifier cord. Do not suspend strings over a crib or attach strings to toys.
•To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing on loose
fasteners.
CA
UTION
:
Any mattress used in this crib should be
atleast 27−1/4 by 51−5/8 in. with a thickness
not exceeding 6 in.

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 3
•D N T place crib near windows where cords from blinds or drapes may strangle a child.
Fall Hazard
•When child is able to pull to a standing position, set mattress to lowest position and remove bumper pads,
large toys and other objects that could serve as steps for climbing out.
•Stop using crib when child begins to climb out or reaches the height of 35 in. (89 cm).
•Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or
sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and other
fasteners.D N T use crib if any parts are missing, damaged or broken. Contact (AFG International
Products Inc) for replacement parts and instructional literature if needed. D N T substitute parts.
Storage: The crib must be kept in a dry and clean area. Solid wood tends to exchange moisture with the
surrounding air and reacts to major changes in temperature and humidity. The ideal environment for the crib is
at a temperature between 65 and 75 degrees and a relative humidity between 35 and 40 percent. If the room is
too humid, the crib willabsorb moisture and expand; in verse, the crib will lose moisure and shrink in a dry
environment. It is best to place your furniture away from heating or air−conditioning vents. Also, direct exposur
to sunlight can discolor the wood, sodo not place your product where it will receive prolonged sunlight exposure.
Care and Cleaning: Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with
mild soap on a soft rag. Rinse and dry thoroughly. If you choose to refinish this furniture, be sure to use only a
non−toxic finish specified for childrens products.
Toddler Bed Warnings
WARNING
INFANTS HAV DI D IN TODDL R B DS FROM NTRAPM NT.
penings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords, around a
child’s neck. These items may catch on bed parts.
CAUTION:
NTRAPM NT HAZARD
To avoid dangerous gaps, any mattress used in the bed shall be a full−size crib mattress at least
51−5/8 in. (1310 mm) in length, 27−1/4 in. (690 mm) in width., and a max thickness of 5 in. (130 mm).
•The maximum weight shall not be greater than 50 lbs (22.7kg).
•Do not use with less than 12 inches of space between toddler bed and solid objects such as a wall or
dresser. Child could slide into smaller spaces and suffocate.
•D N T use a water mattress.
•D N T use casters on toddler bed.
•Guardrails if provided must be used to avoid the formation of a gap between the mattress and the bed that
could cause an entrapment. If mattress retention clips are provided they must be used to restrict mattress
movement.

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 4
G611, 612 Parts Identification Sheet
DO NOT assemble crib if parts are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Parts
A. Headboard
(1 pc)
B. Footboard
(1 pc)
C. Back Stationary Side Panel
(1 pc)
D. Front Stationary Side Panel
(1 pc)
E. Stabilizer Bar
(1 pc)
F. Mattress Support
(1 pc)
G. Drawer Front Panel
(1 pc)
H. Drawer Left Side Panel
(1 pc)
I. Drawer Right Side Panel
(1 pc)
J. Drawer Back Panel
(1 pc)
K. Drawer Divider
(1 pc)
L. Drawer Bottom
Panel (2 pcs)
M. Guardrail
(1 pc)

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 5
G611, 612 Hardware Identification Sheet
DO NOT assemble crib if parts are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Hardware
Item # Fittings Qty
1. Bolt M6 * 60mm (10 pcs)
2. Bolt M6 * 17mm (4 pcs)
3. Wrench (1 pc)
4. Barrel Nut (10 pcs)
5. Screw (12pcs)
6. Bolt M6 * 45mm (1 pc)
7. Wood Dowel 8 * 30mm
(6 pcs)
PHILLIPS SCREWDRIVER (NOT INCLUDED)

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 6
A. Headboard (1 pc) G. Drawer Front Panel (1 pc)
B. Footboard (1 pc) H. Drawer Left Side Panel (1 pc)
C. Back Stationary Side Panel (1 pc) I. Drawer Right Side Panel (1 pc)
D. Front Stationary Side Panel (1 pc) J. Drawer Back Panel (1 pc)
E. Stabilizer Bar (1 pc) K. Drawer Divider (1 pc)
F Mattress Support (1 pc) L. Drawer Bottom Panel (2 pcs)

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 7
G611, 612 Drawer Assembly Sheet
STEP 1:
Attach Drawer Left Side Panel (H), Drawer Right Side Panel (I) and Drawer Divider (K) to Drawer Back
Panel (J) by using 6 Screws (#5). Tighten firmly with Phillips screwdriver.
STEP 2:
Slide Drawer Bottom Panels (L) into the grooves.

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 8
G611, 612 Drawer Assembly Sheet
STEP 3:
Attach Drawer Front Panel (G) to Drawer Left Side Panel (H), Drawer Right Side Panel (I) and Drawer
Divider (K) by using 6 Screws (#5). Tighten firmly with Phillips screwdriver.
Drawer Complete

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 9
G611, 612 Crib Assembly Sheet
STEP 1:
Attach Headboard (A) and Footboard (B) to Back Stationary Side Panel (C), inserting 2 dowels (#7)
on top rail of the Back Stationary Side Panel and inserting 4 Barrel Nuts (#4) from underside of each
corner of the Back Stationary Side Panel before securing 4 Bolts (#1). Attach all parts loosely together,
but do not tighten yet.

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 10
G611, 612 Crib Assembly Sheet
STEP 2:
Attach Mattress Support (F) by swinging out the four hangers at the corners of the mattress support
and use 4 Bolts (#2) to attach hangers to the brackets on the Headboard (A) and Footboard (B) at an
even level on all sides. Attach all parts loosely together, but do not tighten yet.
WARNING:
Make sure that the warning envelope on the
mattress support frame is facing up.
Check components periodically, make sure hinges
are tightened properly and securely.

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 11
G611, 612 Crib Assembly Sheet
STEP 3:
Attach Front Stationary Side Panel (D) to Headboard (A) and Footboard (B),label facing outside, inserting 2
dowels (#7) on top rail of the Front Stationary Side Panel and inserting 4 Barrel Nuts (#4) from underside of each
corner of the Front Stationary Side Panel before securing 4 Bolts (#1). Attach all parts loosely together, but do
not tighten yet.
STEP 4:
Attach Stabilizer Bar (E) to Headboard (A) and Footboard (B) , inserting 2 dowels(#7) and inserting 2 Barrel Nuts
(#4) into Stabilizer Bar before securing 2 Bolts (#1). Tighten all screws firmly with Wrench (#3).

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 12
STEP 5:
Evenly slide the drawer along the rails beneath the crib.
Complete

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 13
G611, 612 Day Bed Assembly Sheet
*Mattress Support Assembly must be in the lowest position before installing guardrail.
a. Loosen the Front Stationary Side Panel (D) bolts to detach the Front Stationary Side Panel (D).

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 14
G611, 612 Toddler Bed Assembly Sheet
*Mattress Support Assembly must be in the lowest position before installing guardrail.
a. Attach Guardrail (M) to Stabilizer Bar by using 2 Bolts (#1), label facing outside, and Headboard (A) by using
1 Bolt (#6) and 1 Bolt (#1).

2015 AFG Baby Furniture G611, 612 Assembly Sheet © 15
Safety Tips for Assembling and Re-assembling Cribs
•Parents should not use any crib with missing, broken or loose hardware parts. Crib slats or spindles should be spaced
no more than 2-3/8” apart, and none should be loose or missing. NEVER use a crib with corner posts over 1/16” of an
inch above the end panels (unless they are over 16” high for a canopy).
•Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges
before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use
crib if any parts are missing, damaged or broken. Contact (AFG International Products Inc.) for replacement parts and
instructional literature if needed. DO NOT substitute parts.
•Never place infants to sleep on pillows, sofa cushions, adult beds, waterbeds, beanbags, or any other surface not
specifically designed for infant sleep.
•Always check all sides and corners of the crib to assure proper assembly with no openings that may entrap a child.
The crib mattress should fit snugly with no more than two fingers width, one-inch, between the edge of the mattress
and the crib side. Otherwise, the baby can get trapped between the mattress and the side of the crib.
•Do not try to repair any side of the crib without manufacturer-approved hardware.
•Putting a broken side up against the wall is not a solution and can often make the situation worse.
•When re-assembling the crib for your second child, please keep in mind that the screw holes will need to be filled in
order for the screws to grip to the wood. Talk to your local hardware store or lumberyard about how to do it properly.
One year limited warranty
AFG International Products Inc. © wants you to be satisfied with any product that bears the AFG name or logo. We will
provide promptly, at the request of the retailer, and without charge, any missing parts that have been reported, with proper
description, within 7 days of the purchase of the products. Our warranty guarantees optimal workmanship and lack of
significant defects. The product warranty lasts a year from the date of your purchase. Please keep the original receipt so
that we may process your one year limited warranty request. This warranty only covers new units with original packaging.
Ownership of the warranty is non-transferable. The warranty does not cover any used, second-hand, or demo models. Our
obligation under this warranty is to replace or repair the merchandise, at our option, free of charge. This warranty does not
cover any damaged or defective parts that result from normal wear and tear, abuse, negligence, improper use or alteration
to the finish design, and hardware. Specific rights issued by this warranty may vary from state to state. Some states do not
allow limitations on how long implied warranties last. DO NOT return products to the store once a product is used, it cannot
be resold and the materials and energy invested in the product would go to waste. In the event that AFG determines that a
defect that may result from customer abuse or misuse, we will contact you with information about services and methods to
prevent occurrences. We strongly recommend you register your product with our company by filling out registration and
mailing it back to us. This ensures you are up-to-date with our products’ maintenance and information.
This warranty does not cover damage caused by accident, misuse or any use other than as intended and described in this
assembly sheet or damage resulting from failure to maintain and clean this product as specified in this assembly sheet.
This warranty applies only to the original purchaser of the AFG International Products Inc. product.
Care and Maintenance
•Storage: The crib must be kept in a dry and clean area. Solid wood tends to exchange moisture with the surrounding
air and reacts to major changes in temperature and humidity. It is best to place your furniture away from heating or air-
conditioning vents. Direct exposure to sunlight can discolor of the wood, so do not place your product where it will
receive prolonged sunlight exposure.
•Care and Cleaning: Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning. Clean with mild
soap on a soft rag. Rinse and dry thoroughly. If you choose to refinish this furniture, be sure to use only a non-toxic
finish specified for children’s products.
•Wood is a natural material. As such, it can be affected by changes in temperature and humidity. Extreme changes in
humidity and temperature can cause the wood to warp, swell, crack, or shrink, thus compromising the structural
integrity of the crib and making it dangerous to use.
CAUTION! Safety Tips for Use of Cribs
Many older cribs, including secondhand or second use cribs, may not meet all current safety
standards. For baby’s safety, even if you are on a tight budget, you should not purchase a used
crib at a garage sale or accept a hand-me-down that does not meet the most recent Federal and
ASTM standards.
Thank you for choosing AFG.
MADE IN CHINA AFG ©