AFG G4688 User manual

4-in-1 Convertible Crib
THIS PRODUCT IS NOT INTENDED FOR INSTITUTIONAL OR COMMERCIAL USE.
If you have any questions or missing parts, contact us. DO NOT return product parts
to the store from where it was purchased before contacting AFG Customer Service.
AFG Customer Service:
E-mail: [e-mail]
Tel: [phone]
Model
#
:
G
4688
PO #:
Serial #:

2019 AFG Baby Furniture G4688 Assembly Sheet 1
WARNING:
READ ALL WARNING & SAFETY INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP
INSTRUCTIONS WITH CRIB FOR FUTURE USE.
First remove hardware from box and sort by size. Check to see that all hardware and wooden pieces
are present before assembling.
Follow instructions listed below in the proper sequence as numbered to assure fast, easy and correct
assembly.
WARNING:
•DO NOT attempt to repair or modify parts with cracks or defects. Please contact us for
immediate replacement.
•This product is for home use and is not intended for use in schools, day care centers or other
commercial establishments.
•Must be assembled by a capable adult.
Crib Warnings
WARNING
Failure to follow these warnings and the assembly instructions could result in serious injury or death.
•This crib conforms to applicable regulations promulgated by the Consumer Products Safety
Commission.
•To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
•DO NOT use a water mattress with this crib.
•If refinishing, use a non-toxic finish specified for children’s products.
•Check fasteners periodically and never over tighten then, as this may cause distortion or breakage.
•Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
•CAUTION: ANY MATTRESS USEDIN THIS CRIB MUST BE AT LEAST 27-1/4 IN BY 51-5/8 IN
(69CM X 131CM) WITH A THICKNESS THAT DOES NOT EXCEED 6 IN (15CM).
•Never leave child unattended inside crib. Remember that a crib is not a substitute for a parent’s
supervision.
•Parents should ensure a safe environment for their child by checking the crib regularly before
placing the child in the products. Please make sure that every component is properly and securely
in place.
•When a child is able to pull to a standing position, set the mattress tothe lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out.
•Infants can suffocate in gaps between crib sides and a mattress that is too small.
•Follow warnings on all products in a crib.
WARNING
Infants can suffocate on soft bedding.
Never add a pillow or comforter.
Never place additional padding under an infant.

2019 AFG Baby Furniture G4688 Assembly Sheet 2
Strangulation Hazard
•Strings can cause strangulation! Do not place items with a string around a child’s neck, such as
hood strings or pacifier cord. Do not suspend strings over a crib or attach strings totoys.
•To help prevent strangulation, tighten all fasteners. A child can trap parts of the body or clothing
on loose fasteners.
•DO NOT place crib near windows where cords from blinds or drapes may strangle a child.
•Keep wall decorations, especiallythose with strings, completely out of a child’s reach.
Fall Hazard
•When child is able to pull to standing position, set mattress to lowest position and remove bumper
pads, large toys and other objects that could serve as steps for climbing out.
•Stop using crib when child begins to climb out or reaches the heights of 35 in. (89cm).
•Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing
parts, or sharp edges before and after assembly and frequently during use. Securely tighten loose
bolts and other fasteners. DO NOT use crib if any parts are missing, damaged or broken. Contact
(AFG International Products Inc.) for replacement parts and instructional literature if needed. DO
NOT substitute parts.
Storage: The crib must be kept in a dry and clean area.
Care and Cleaning: Do not scratch or chip the finish. Do not use abrasive chemicals for cleaning.
Clean with mild soap on a soft rag. Rinse and dry thoroughly. If you choose to refinish this furniture, be
sure to use only a non-toxic finish specified for children’s products.
Toddler Bed Warnings
WARNING ENTRAPMENTS
STRANGULATIONS HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and assembly instructions could result in serious injury or death.
•The mattress intended for use on the bed shall be a full size crib mattress having a minimum
dimension 51-5/8 inches (1310mm) in length and 27-1/4 inches (690mm) in width and 4 inches
(100mm) in thickness.
•The minimum age for a child using this toddler bed shall not be less than 15 months and the
maximum weight shall not be greater than 50 lbs. (22.7 kg)
•DO NOT use with less than 12 inches of space between the toddler bed and solid objects such as
a wall or dresser. Child could slide into smaller space and suffocate.
•NEVER place bed near window where cords from blinds or drapes may strangle a child.
•Strings can cause strangulation! DO NOT place items with a string around a child’s neck, such as
hood strings or pacifier cords. DO NOT suspend strings over a crib or attach strings to toys.
•DO NOT use a water mattress.
•DO NOT use casters on toddler bed.
•DO NOT suspend strings over a toddler bed for any reason.
•If guardrails are provided as the mattress containment means, guardrail(s) provided must be used
to avoid the formation of a gap between the mattress and the bed that could cause entrapment. If
mattress retention clips are provided they must be used to restrict mattress movement.

2019 AFG Baby Furniture G4688 Assembly Sheet 3
G4688 Parts Identification Sheet
DO NOT assemble crib if parts are defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Parts
A. Left Side Panel (1 pc) B. Right Side Panel (1 pc) C. Headboard (1 pc)
D. Footboard (1 pc) E. Stabilizer Bar (1 pc) F. Mattress Support (1 pc)
G. Left Rear Leg (1 pc) H. Right Rear Leg (1 pc) I. Toddler Bed Guardrail (1 pc)
*Sold Separately
(Full Size Conversion Kit)
J. Bed Rail (2 pcs), K. Bed Slat (7 pcs)
*Sold Separately

2019 AFG Baby Furniture G4688 Assembly Sheet 4
G4688 Hardware Identification Sheet
DO NOT assemble crib if hardware is defective or missing.
Contact AFG for exchange or keep the original box for return authorization.
~ Crib Assembly Hardware
Item # Fittings Qty
1. Bolts 1/4" x 3-1/4”
(4 pcs)
2. Bolts 1/4" x 1-1/2”
(12 pcs)
3. Bolts 1/4” x 4” (6 pcs)
4. Phillip Head Screw 1-1/4”
*Sold with Full Size
Conversion Kit
(28 pcs)
5. Barrel Nut
(10 pcs)
6. Wrench
(1 pc)
7. End Cap
(6 pcs)
8. Bolts 1/4” x 5/8”
(6 pcs)
9. Bolts 1/4” x 3/4”
(4 pcs)

2019 AFG Baby Furniture G4688 Assembly Sheet 5
G4688 Crib Parts Diagram
Please follow this Parts Diagram to make sure that all
crib parts are assembled in the correct position.
A. Left Side Panel (1 pc)
B. Right Side Panel (1 pc)
C. Headboard (1 pc)
D. Footboard (1 pc)
E. Stabilizer Bar (1 pc)
F. Mattress Support (1 pc)
G. Left Rear Leg
H. Right Rear Leg
(1 pc)
(1 pc)
A
B
C
D
F
E
G
H

2019 AFG Baby Furniture G4688 Assembly Sheet 6
G4688 Crib Assembly Sheet
STEP 1:
Insert six Barrel Nuts (#5) into the holes on the back of Headboard (C). Then, use six Bolts (#3) to
secure Left Rear Leg (G) and Right Rear Leg (H) to the Headboard. Make sure the holes on the legs
are facing forward with the front of the Headboard (you should not see barrel nuts if everything is facing
forward).
1
6
E
1
(4 pcs)
5 (4 pcs)
6 (1 pc)
STEP 2:
Attach Left Side Panel (A) and Right Side Panel (B) to Stabilizer Bar (E) by using four Bolts (#1) and
Barrel Nuts (#5). Tighten firmly with Wrench (#6).
C
G
H
Back of Headboard
Back of Headboard
3 6 pcs
5
6 pcs
6 1 pc
3
3
3
3
5
5
5
5
3
3
Back of Headboard
5

2019 AFG Baby Furniture G4688 Assembly Sheet 7
G4688 Crib Assembly Sheet
STEP 3:
Attach Left Side Panel (A) and Right Side Panel (B) to Headboard (C) by using six bolts (#2). Tighten
firmly with Wrench (#6).
STEP 4:
a. Attach Mattress Support (F) (flat side up). Swing out four hangers at corners of the mattress
support and insert four Bolts (#9) on them to attach the mattress support to the brackets.
b. Choose the height of the mattress support. Make sure the mattress suport is at the same level on both
side panels. Adjust accordingly.
2
2 (6 pcs)
6 (1 pc)
9 (4 pcs)
6 (1 pc)
9

2019 AFG Baby Furniture G4688 Assembly Sheet 8
G4688 Crib Assembly Sheet
STEP 5:
Attach Left Side Panel (A) and Right Side Panel (B) to Footboard (D) by using six Bolts (#2). Tighten
firmly with Wrench (#6).
Complete
2 (6 pcs)
6 (1 pc)

2019 AFG Baby Furniture G4688 Assembly Sheet 9
G4688 Day Bed Assembly Sheet
*Mattress Support Assembly must be in the lowest position before installing
guardrail.
a. Disassemble the Footboard (D) from crib by unscrewing the footboard bolts (#2).
b. Fill in all the bolt holes on the front legs of both side panels using End Caps (#7) and
Bolts (#8). Tighten firmly with Wrench (#6).
6. (1 pc) 7. (6 pcs)
8. )scp6(

2019 AFG Baby Furniture G4688 Assembly Sheet 10
G4688 Toddler Bed Assembly Sheet
(Guardrail not included)
*Mattress Support Assembly must be in the lowest position before installing
guardrail.
a. Disassemble the Footboard (D) by unscrewing the footboard bolts (#2).
b. Fill in the top bolt holes on the front legs of both side panels using End Caps (#7) and
Bolts (#8). Tighten firmly with Wrench (#6).
c. Attach Guardrail (I) to Left Side Panel (A) and Right Side Panel (B) by using four Bolts
(#2). Tighten firmly with Wrench (#6).
2. (4 pcs) 6 (1 pc)
7. (2 pcs) 8 (2 pcs)

2019 AFG Baby Furniture G4688 Assembly Sheet 11
G4688 Full Size Bed Assembly Sheet
(Full Size Conversion Kit notincluded)
STEP 1:
Fill in the top two bolt holes on the legs of Headboard (C) by using Bolts (#8). Tighten firmly with Wrench
(#6).
6
(1 pc)
8 (4 pcs)
STEP 2:
Slide hangers of the Bed Rails (H) into the grooves on the legs of the Headboard (A) and Footboard (B)
and push down. Make sure the Bed Rails attach to the Headboard and Footboard firmly.

2019 AFG Baby Furniture G4688 Assembly Sheet 21
G4688 Full Size Bed Assembly Sheet
STEP 3:
Attach Bed Slats (K) to Bed Rails (H) by using Philip Head Screws (#9).
K
9 (28 pcs)
Finish

2019 AFG Baby Furniture G4688 Assembly Sheet © 13
Product Assistance Procedures
AFG International Products strives to ensure that our customers are receiving a quality piece of
furniture. We want our customers to be satisfied with using our products for years to come. In
the event that you need assistance or have any inquiries regarding our products, please feel
free to contact us with the information below.
Under no circumstances should you remove any warning labels from the product. These labels
are meant to be permanent and removing them may damage the wood and void your
warranty.
To request replacement parts, please send an email to our customer service with the following
information and we will do our best to assist you.
1. Proof of Purchase*
2. Item Number of the Product or Identification Sticker**
3. Part Letter or Number of the Replacement Part
4. Quantity
5. Your Shipping Address
6. Description of Your Problem
Please also provide pictures of the issue whenever possible. This will help us understand and assist
you with your problem.
Customer Service Email: [email protected]
Customer Service Phone Number: 1.323.722.6268
**All of our baby products come with an identification sticker. This is a white sticker that contains all the
product information of the item.
For cribs, the identification sticker is generally located near the bottom of the crib’s side rails, the toddler
guardrail, or the stabilizer bar.
For changing tables, the identification sticker is located on the top panel of the changing unit.
*Acceptable Proof of Purchase includes, but not limited to, your Online Purchase Confirmation Email, a
screenshot of the purchase history of the online retailer, or a receipt from your local store.
Our warranty extends only to the original purchaser and is non transferable. Warranty is valid
only when the proof of purchase can be provided.
Please retain a copy of your purchase records for future inquires.
AFG International Products Inc.
945 S. Greenwood Ave
Suite #L
Montebello, CA 90640

2019 AFG Baby Furniture G4688 Assembly Sheet 41
Safety Tips for Assembling and Re-assembling Cribs
•Parents should not use any crib with missing, broken or loose hardware parts. Crib slats or spindles should be
spaced no more than 2-3/8” apart, and none should be loose or missing. NEVER use a crib with corner posts over
1/16” of an inch above the end panels (unless they are over 16” high for a canopy).
•Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts, or sharp edges
before and after assembly and frequently during use. Securely tighten loose bolts and other fasteners. DO NOT use
crib if any parts are missing, damaged or broken. Contact (AFG International Products Inc.) for replacement parts
and instructional literature if needed. DO NOT substitute parts.
•Never place infants to sleep on pillows, sofa cushions, adult beds, waterbeds, beanbags, or any other surface not
specifically designed for infant sleep.
•Always check all sides and corners of the crib to assure proper assembly with no openings that may entrap a child.
The crib mattress should fit snugly with no more than two fingers width, one-inch, between the edge of the mattress
and the crib side. Otherwise, the baby can get trapped between the mattress and the side of the crib.
•Do not try to repair any side of the crib without manufacturer-approved hardware.
•Putting a broken side up against the wall is not a solution and can often make the situation worse.
•When re-assembling the crib for your second child, please keep in mind that the screw holes will need to be filled in
order for the screws to grip to the wood. Talk to your local hardware store or lumberyard about how to do it properly.
One year limited warranty
AFG International Products Inc. © wants you to be satisfied with any product that bears the AFG name or logo. We will
provide promptly, at the request of the retailer, and without charge, any missing parts that have been reported, with proper
description, within 7 days of the purchase of the products. Our warranty guarantees optimal workmanship and lack of
significant defects. The product warranty lasts a year from the date of your purchase. Please keep the original receipt so
that we may process your one year limited warranty request. This warranty only covers new units with original packaging.
Ownership of the warranty is non-transferable. The warranty does not cover any used, second-hand, or demo models. Our
obligation under this warranty is to replace or repair the merchandise, at our option, free of charge. This warranty does not
cover any damaged or defective parts that result from normal wear and tear, abuse, negligence, improper use or alteration
to the finish design, and hardware. Specific rights issued by this warranty may vary from state to state. Some states do not
allow limitations on how long implied warranties last. DO NOT return products to the store once a product is used, it cannot
be resold and the materials and energy invested in the product would go to waste. In the event that AFG determines that a
defect that may result from customer abuse or misuse, we will contact you with information about services and methods to
prevent occurrences. We strongly recommend you register your product with our company by filling out registration and
mailing it back to us. This ensures you are up-to-date with our products’ maintenance and information.
This warranty does not cover damage caused by accident, misuse or any use other than as intended and described in this
assembly sheet or damage resulting from failure to maintain and clean this product as specified in this assembly sheet.
This warranty applies only to the original purchaser of the AFG International Products Inc. product.
CAUTION! Safety Tips for Use of Cribs
Many older cribs, including secondhand or second use cribs, may not meet all current safety
standards. For baby’s safety, even if you are on a tight budget, you should not purchase a used
crib at a garage sale or accept a hand-me-down that does not meet the most recent Federal and
ASTM standards.
Thank you for choosing AFG.
MADE IN CHINA AFG ©