AFLAMO LED 50 User manual

1
Electric Fireplace
OWNER’S MANUAL
Model: LED 50
Dear customer：
Thank you very much for choosing our products, it’s our
pleasure to offer you our products and service. Please read the user manual
carefully before using the applia
nce and operate following the operation
instructions in this manual, in order to prevent fire or other accidental danger.
Keep this manual in a safe place for future reference. Any understanding
problem relates to this manual please contact your dealer.
www.aflamo.pl/en/
Polski s. 18

2
Guide for Quick Reference
I. Please ensure the following points before installation:
Circuit breaker is open or not(Please follow up the instruction strictly).
II. The heater of the
electric fireplace may give off a little harmless odor for the
first time, which is a normal phenomenon of the heating unit when it is first
used. It will disappear afterwards.
III. Regarding the fireplace related information, please check the rating label at
the back of fireplace. The rated voltage and power supply of electric
fireplace shall be the same.
IIII. In case that the fireplace fails to give off heat, please ensure the heating
switch is in the correct position before making further treatment. For detailed
information, please refer to the section of operation in the specification
Contents
Page 3IMPORTANT SATETY INSTRUCTIONS
Page 6TECHNICAL SPECIFICATIONS
Page 6DIMENSIONS
Page 7ELECTRIC FIREPLACE INSTALLATION
Page 8OPERATING INSTRUCTIONS
Page 18CLEANING AND MAINTENANCE
www.aflamo.pl/en/

3
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, basic precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons
including the following:
1. Read all instructions before using this appliance.
2. This appliance is hot when in use. To avoid burns,
don’t let bare skin
touch hot surfaces. The grill at the top
of this heater in particular will
become hot when the heater is active. Keep combustible materials such
as furniture, pillows, bedding, papers, clothes and curtains etc. At least 3
feet ( 0.9m)away from the front of the appliance.
Keep all items away
from the sides and back of the appliance and take special care not to
block the air intake or exhaust vents.
Use handles when moving this
heater.
3. Extreme caution is necessary when the appliance
is used by or near
children or invalids and whenever the heater
is left operating and
unattended.
4. Do not operate
the appliance if the power cord or plug has been
damaged or the heater h
as been damaged or malfunctioned in any way.
Take the appliance to authorized service facility for examination,
electrical or mechanical adjustment or repair.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
NO USER-SERVICEABLE PARTS INSIDE
5. Do not use outdoors.
6. Do not use the appliance in bathrooms, laundry areas and similar indoor
locations, Never locate the appliance
where it may fall into a bathtub or
other water container.
7. Do not run the power cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings.
Do not route cord under furniture or
appliances.
Take care to position the cord away from high traffic areas
and such that it can not be tripped over.
8. To disconnect the appliance, turn all controls “OFF”,
then remove the
plug from the outlet.
9. This appliance has a polarized plug
(one blade is wider than the other).
This plug will fit in a fully in a outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does fit, contact a qualified
electrician to install the proper outlet. Do not change the plug in any way.
Warning: Any use of this appliance other than recommended by the
manufacturer in this user manual may cause fire, burns, electric shock and /or
other serious injuries.
www.aflamo.pl/en/

4
10. Do not insert or allow foreign objects to enter any ventilation or exhaust
opening as this may cause an electric shock or fire, or damage the
appliance.
11. To prevent a possible fire,
do not block air intakes or exhaust in any
manner. Do not use on soft surfaces like a bed,
where openings may
become blocked.
12. Aheater has hot and arcing or sparking parts inside. Do not use in areas
where gasoline, paint or flammable liquids are used or stored.
13. Use this heater only as described in this manual. Any other
use not
recommended by the manufacturer may cause fire, electric shock or
injury to persons.
14. Always plug heaters directly into a wall outlet/receptacle. Never use with
an extension cord or reloadable power tap.
15. Do not attempt burn wood or other materials in this heater.
16. Do not strike the glass of fireplace.
17. The installation of circuit and socket shall be
conducted by certificated
electrician.
18.
When transporting or storing the heater, take care to keep both the unit
and power cord/plug dry, free from excessive vibration and away from
heat sources.
19. This appliance comes equipped with an overheat protection safety
device. S
hould the appliance begin to overheat for any reason, it will
automatically turn all heater functions of the appliance off. The appliance
will have to be reset prior to continuing use. T
o reset the overheat
protection safety device, turn all controls, wait 15 minutes,
plug the
appliance back in and turn on.
20. Please use the socket with excellent earth, fuse and earth electrode.
21.
Please ensure the earth leakage protection is always connected as per
electrical circuitry code.
22. Please pull out the p
ower plug when cleaning, maintaining or remove
the fireplace.
23. In order to avoid overheating, do not cover the heater.
www.aflamo.pl/en/

5
SAVE THIS MANUAL
You will need this manual for safety instructions, operation
procedures, and warranty. Put it and the original invoice
in a
safe, dry place for future reference.
Reminder
：Please pay attention to the operation steps and
technical specifications.
Warning
：Operating instructions shall be followed strictly;
otherwise, it may cause fireplace damaged.
Warning: Operating instr
uctions shall be followed strictly;
otherwise, it may cause fire, or seriously injured or cause
disease or dead.
4
www.aflamo.pl/en/

6
TECHNICAL SPECIFICATIONS
DIMENSIONS:
Rated voltage
AC 230V
，
50Hz
Rated Power
1800W
Power of Heating Apparatus
900W/1800W
Flame Power
4W
www.aflamo.pl/en/

7
Note:
A 10AMP, 230V circuit is required to operate this appliance. Dedicated circuit
is preferred but not essential in all cases, a dedicated circuit will be required if,
after installation, the circuit breaker trips or the fuse blows on a regular basis
when the heater is operating. Additional appliance on the same circuit may
exceed the current rating of the circuit break.
Warning:
1.
Ensure the power cord is not installed so that it is pinched or against a
sharp edge and ensure that the power cord is stored or secured to avoid
tripping or snagging to reduce the risk of fire, electric shock or injury to
persons.
2.
Construction and electrical outlet wiring must comply with local building
codes and other applicable regulations to reduce the risk of fire, electric
shock and injury to persons.
3.
Do not attempt to wire your own new outlets or circuits. To reduce the risk
of fire, electric shock or injury to persons, always use a licensed
electrician.
INSTALLATION:
1. Please confirm the power is off when you start to installation.
2.
Plug in the unit into the power, the power should be no less than
10Amp/230V AC. If the power cord is not long enough, you can use
an extension cord that the power is no less than 2000W.
www.aflamo.pl/en/

8
OPERATING INSTRUCTIONS：
Control Panel:
Master Power Switch (A)
Open the cover and push button Adown (I) to “ON” position.
ON/OFF(B)
Press button B(ON/OFF) to begin the flame effect.
Default interface displays as following:
Two short beeps that incre
ase in pitch sound when switched on and three
beeps that decrease in pitch sound when switched off.
When switches on, the heating level, set temperature and clock
icon are
displayed. The display will be disappeared after 60 second without any
operation. Press any button to display again.
Locking the Buttons(C)
Press and hold button C(OK) for more than 6 seconds to lock or unlock the
buttons, LOC is displayed and indicated that the buttons are locked. Once it’s
locked LOC will be flashing for 6 seconds then disappear
, press any button
LOC will flash again. Long press button C(OK) for 6 seconds to unlock the
buttons.
Please note the button B(ON/OFF) is never locked.
A
B
C
D
E
F
The heating icon will display and start heating when the room
temperature is less than the default setting (10°C), on the contrary it
will not display and heat.
The clock icon will be flashing because the time is not set yet.
Please follow the steps in “Time Setting” to set the time.
www.aflamo.pl/en/

9
Heating ON/OFF
Heating Mode Quick Start
Press button E(+) or F(-) to quick start heat setting(Even though it’
s under
weekly program) as following:
a. Press either button E(+) or F(-) to see the current temperature on screen.
b. Press button E(+) or F(-
) to adjust the temperature as desired. Press
button C(OK) to validate the setting. If the set
temperature is higher than
the room temperature detected by appliance, the heating starts. The
heating will not start if the set temperature is lower than the room
temperature.
NOTE: The temperature range including OFF, from 10°C to 30°C
and ON.
OFF for no heating, 10°C to 30°C
is the selectable temperatures and ON for
continuous heating.
LOW/HIGH HEATING & SETTING THE TEMPERATURE
High Heating
At default interface, press button
D(MENU) to display H and flashing heating
icon as following:
Press OK button to set temperature. The default temperature is 10°C(50°F).
It’s displayed as following:
Press button E(+) or F(-) to adjust temperature.
If the set temperature is higher
than the room temperature detected by appliance, the heating starts. The
heating will not start if the set temperature is lower than the room temperature.
www.aflamo.pl/en/

10
Low Heating
At default interface, press button
D(MENU) twice to display L and flashing
heating icon as following:
Press OK button to set temperature. The default temperature is 10°C(50°F).
It’s displayed as following:
Press button E(+) or F(-) to adjust temperature. If the set temperature is higher
than the room temperature detected by appliance, the heating starts. The
heating will not start if the set temperature is lower than the room temperature.
Celcius/Fahrenheit Setting:
The default temperature readout is Celcius. Long press button D(MENU) for 3
seconds then press button E(+) or F(-)
to change the temperature readout
from Celcius to Fahrenheit.
Brightness Control
Brightness Control is to select the desired flame brightness level.
At default interface, keep pressing button
D(MENU) to select the Brightness
Control, it’s displayed “bri” and flashing light bulb icon as following:
Press OK button to start the brightness setting. Press button E(+) or F(-
) to
select the brightness level.
5 brightness levels are selectable. Default setting is 3. 5 is the highest level as
shown following:
www.aflamo.pl/en/

11
Regular Timer
At default interface, keep pressing button D(MENU) to select the regular timer,
it’s displayed “Hour” and flashing timer icon as following:
Press OK button to start the regular timer setting.
Press button E(+) or F(-) to select the desired time.
The time sequence will read 00-
30min, 1H, 2H, 3H, 4H, 5H, 6H, 7H, 8H and
9H. The default setting is 00 as shown following:
Down Light
At default interface, keep pressing button D(MENU) to select the down light,
it’s displayed “doLi” as following.
Press OK button to start the down light setting.
Press button E(+) or F(-) to select the down light levels. Levels including
D1/D2/D3/D4/OFF.
D1 is the brightness level, OFF is no down light.
NOTE: This appliance doesn’t have down light function.
NOTE: The display will return to default interface
after 15 seconds without any
operation on control panel or remote control.
www.aflamo.pl/en/

12
Mode Selection(Secondary Menu)
At default interface, keep pressing button
D(MENU) to select Mode Selection,
it’s displayed “Mode” as following:
Press OK button to access Mode menu.
Press button E(+) or F(-) to select the desired mode.
1) Open Window Detection Mode
Keep pressing button D(MENU) to select Mode menu.
Press OK to validate, then E(+) or F(-
) to access Open Window Detection
Mode. The screen show “OPEN” as following:
Press OK to validate, then button E(+) or F(-
) to select ON or OFF. Press OK
button to turn on or turn off the Open Window Detection Mode.
After activate the Open Window Detection, the appliance will automatically
shut off the heating when it detects the room temperature decreased more
than 4°C
in 10 minutes and maintain the decreased temperature not less than
20 minutes.
To restart the heating, adjust the set temperature then press OK button to
validate the setting. The Open Window Detection Mode will be OFF after reset
the temperature.
2) Time Setting
Keep pressing button D(MENU) to select Mode menu.
Press OK to validate, then button E(+) or F(-) to access Time Setting. It’s
displayed “TIME” as following:
www.aflamo.pl/en/

13
Press OK to validate, then button E(+) or F(-) to select day, D1 for Monday, D2
fo
r Tuesday, D3 for Wednesday, D4 for Thursday, D5 for Friday, D6 for
Saturday and D7 for Sunday.
Press OK to validate the day, then button E(+) or F(-) to set time(hour).
Press OK to validate the hour, then button E(+) or F(-) to set time(minute).
Press OK to validate the time setting.
To exit the setting during operation, press button D(MENU).
If icon permanently flashes, this indicates that the
time is offset
following a power cut. It’s flashing as a time has not been set.
3) Weekly Programming
The time must be set before any programming.
3 pre-set programs are available. Each program includes a time period or
several time periods during which the electric fireplace is under heating mode.
Outside of the time periods, the electric fireplace is non-heating.
The time period of one program may overlap the time period of another.
Program Definition:
P1 as Program 1:
Monday to Friday from 05:15 for 4 hours high heating, and Saturday to Sunday
from 06:20 for 4 hours low heating.
P2 as Program 2:
Monday
to Friday from 17:45 for 4 hours high heating, and Saturday to Sunday
from 16:30 for 4 hours low heating.
P3 as Program 3:
Saturday to Sunday from 08:15 for 4 hours high heating.
www.aflamo.pl/en/

14
Keep pressing button D(MENU) to select Mode menu.
Press OK to validate, then button E(+) or F(-) to access Weekly Programming,
it’s displayed “ProG” as following:
Press OK to validate, then button E(+) or F(-
) to select the
program(P1/P2/P3/OFF). OFF is to turn off the weekly program.
Press OK to validate.
To exit the setting during operation, press button D(MENU).
To cancel an existing weekly program, select OFF to turn off the weekly
program.
Manual Setting for Weekly Programming
Keep pressing button D(MENU) to select Mode menu.
Press OK to validate, then button E(+) or F(-) to access Manual Setting, it’s
displayed “MANU” as following:
Press OK to validate, then button E(+) or F(-
) to select the program(P1~P3)
want to make change.
Press OK to validate after select the program code (P1~P3).
Press button E(+) or F(-) to
select the day(s) of program activation or
inactivation. Press + or – to select the activation day first, press OK to validate;
then press + or – to select the inactivation day, press OK to validate.
Following example for selecting Monday as activation da
y and Sunday as
inactivation day.
www.aflamo.pl/en/

15
Press button E(+) or F(-) to select the heating level. H for high heating and L
for low heating. Press Ok to validate.
Press button E(+) or F(-
) to set your desired temperature. Press OK to
validate.
Press button E(+) or F(-
) to set the hour of the activation time. Press OK to
validate.
Press button E(+) or F(-) to set the minutes of the activation time. Press OK to
validate.
Please note the minute setting is accumulated by 5 minutes each time.
Press button E(+) or F(-
) to set the duration of the time period. Press OK to
validate.
Please note the duration time setting is accumulated by 30 minutes each time.
Till now 1st time period of program is completed. It’s displayed “CON”
(confirm).
NOTE: The program
cannot run into the next day. The maximum duration can
therefore not exceed midnight (for example, if the start time is 20:30, the
maximum duration displayed is 4 hours and the real maximum duration is 3
hours 30 minutes).
www.aflamo.pl/en/

16
To continue the setting for 2nd time period, press OK to continue. After OK, the
screen will return to the interface of day selection for 2nd time period.
To finish the setting, press button E(+) or F(-) to find “FINSH”
, then press OK
to finish the setting.
Multi time periods could be used for one day.
Same time period could be used for multiple days.
NOTE:
For settings under Mode Selection (Secondary Menu) always
remember to
press button C(OK) to validate the setting.
Maximum 8 time periods could be used for one program.
After ma
nual setting for weekly program, the relevant program has done the
manual setting will update the default program setting accordingly.
Restore Factory Defaults
Unplug the appliance for not less than 5 seconds then plug in to restore the
factory defaults.
Using the Remote Control
This heater includes a remote control. T
o operate the appliance using the
remote control, the Master Power Switch (A) must be the “ON” position.
All the buttons on remote control are exactly the same functions as on control
panel.
www.aflamo.pl/en/

17
Battery Replacement
1.
For the first time use the protective plastic tab for the battery must be
removed.
2.
For remote control battery replacement, use a Lithium Cell CR2025 3V
battery.
WARNING: Do not cover the outlet when the appliance is working.
Unplug the power cord when you leave the appliance for a long time.
Turn off the appliance, unplug and let cool for at least 10 minutes before
attempting to service. Only a qualified professional should attempt to
service or repair the appliance.
www.aflamo.pl/en/

18
Cleaning and Maintenance
WARNING: AN
AUTHORIZED SERVICE REPRESENTATIVE SHOULD
PERFORM ANY OTHER SERVICING.
WARNING: TO AVOID FIRE, ELECTRIC SHOCK, PERSONAL INJURED, CLEANING
AND MAINTENACE SHOULD BE DONE ONLY WHILE THE
ELECTRICAL HEATER
IS DISCONNECTED FROM THE POWER SUPPLY.
Glass cleaning
Over time, the front glass panel may become dirty or dusty. Dust can be
removed by lightly rubbing the glass surface with a clean lint-free cloth or
paper towel. To remove fingerprints or other marks, use a soft, damp, lint-free
cloth with a good quality household glass cleaner. The front glass panel
should always be completely dried with a lint-free cloth or paper towel.
STORAGE
When not in use, unplug the unit from the power supply and store it in
a dry, dust-free location.
CAUTION: DO NOT USE ABRASIVE CLEANERS ON THE GLASS PANEL!
DO NOT SPRAY LIQUIDS DIRECTLY ONTO ANY SURFACE OF THE UNIT!
WARNING: AN AUTHORIZED SERVICE REPRESENTATIVE SHOULD
PERFORM ANY OTHER SERVICING.
www.aflamo.pl/en/

1
Kominek elektryczny
INSTRUKCJA UŻYTKOWNIKA
Model: LED 50
Szanowny kliencie, dziękujemy za wybranie naszego produktu. Z
przyjemnością oferujemy nasze produkty i usługi. Prosimy dokładnie zapoznać
się z instrukcją użytkownika przed przystąpieniem do obsługi urządzenia i
postępować zgodnie z przedstawionymi w niej wskazówkami, aby uniknąć
wzniecenia ognia i innych przypadkowych niebezpieczeństw. Instrukcję należy
przechowywać w bezpiecznym miejscu, w celu skorzystania z niej w
przyszłości. W przypadku niezrozumienia treści instrukcji prosimy o kontakt z
naszym dystrybutorem.
www.aflamo.pl

2
Skrócony poradnik
I. Przed rozpoczęciem montażu należy zapewnić poniższe warunki:
Zabezpieczenie elektryczne jest załączone lub nie (należy ściśle
przestrzegać poleceń w instrukcji).
II. Nagrzewnica kominka elektrycznego może wydzielać nieszkodliwy zapach
podczas pierwszego uruchomienia, co jest normalnym zjawiskiem. Zapach
zaniknie po chwili.
III. Informacje na temat kominka dostępne są na tabliczce znamionowej, na
tylnej ściance urządzenia. Napięcie znamionowe powinno być zgodne z
charakterystykami zasilania kominka..
IIII. W przypadku, gdy z kominka nie jest emitowane ciepło, upewnij się, że
przełącznik ogrzewania znajduje się we właściwej pozycji przed
przystąpieniem do dalszych prac. Szczegółowe informacje dostępne są w
dalszej części instrukcji, dotyczącej jego obsługi.
Spis treści
Strona 3 WAŻNE INFORMACJE NA TEMAT BEZPIECZEŃSTWA
Strona 6 SPECYFIKACJE TECHNICZNE
Strona 6 WYMIARY
Strona 7 MONTAŻ KOMINKA ELEKTRYCZNEGO
Strona 8 INSTRUKCJA OBSŁUGI
Strona 18 CZYSZCZENIE I KONSERWACJA
www.aflamo.pl