AG Neovo MX-22 User manual

MX-22 & MX-24 LED-Backlit Display
User Manual

TABLE OF CONTENTS
2
Safety Information
FCC Declaimers ....................................................................................................................................... 4
WEEE....................................................................................................................................................... 5
EMC Information ...................................................................................................................................... 6
Precautions
Notice ....................................................................................................................................................... 9
Cautions When Setting Up ....................................................................................................................... 10
Cautions When Using............................................................................................................................... 11
Cleaning and Maintenance....................................................................................................................... 11
Notice for the LCD Display ....................................................................................................................... 12
Chapter 1: Product Description
1.1 Package Contents .............................................................................................................................. 15
1.2 Wall Mounting Installation Preparation............................................................................................... 16
1.2.1 Wall Mounting.......................................................................................................................... 16
1.2.2 Removing the Base Stand....................................................................................................... 16
1.3 LCD Display Overview ....................................................................................................................... 17
1.3.1 Front View and Keypad Buttons.............................................................................................. 17
1.3.2 Rear View................................................................................................................................ 18
Chapter 2: Making Connections
2.1 Connecting the Power ........................................................................................................................ 19
2.2 Connecting Input Source Signals ....................................................................................................... 20
2.2.1 Connecting a Computer .......................................................................................................... 20
Using VGA Cables ......................................................................................................................... 20
Using DVI Cables........................................................................................................................... 20
Using DisplayPort Cables .............................................................................................................. 21
Using Audio Cables........................................................................................................................ 21
2.2.2 Connecting a Video Device..................................................................................................... 22
Using HDMI Cables........................................................................................................................ 22
Chapter 3: Using the LCD Display
3.1 Turning on the Power ......................................................................................................................... 23
3.2 Selecting the Input Source Signal ...................................................................................................... 23
3.3 Adjusting the Volume.......................................................................................................................... 24
3.4 Locking the OSD Menu ...................................................................................................................... 24
3.5 Using Picture-in-Picture (PIP) ............................................................................................................ 25
3.5.1 PIP Options ............................................................................................................................. 25
3.5.2 PIP Swap................................................................................................................................. 26
3.6 Using Auto Adjustment Function ........................................................................................................ 26
Chapter 4: On Screen Display Menu
4.1 Using the OSD Menu ......................................................................................................................... 27
4.2 OSD Menu Tree ................................................................................................................................. 29

3
TABLE OF CONTENTS
Chapter 5: Adjusting the LCD Display
5.1 BRIGHTNESS .................................................................................................................................... 32
5.2 COLOUR TEMP.................................................................................................................................. 34
5.3 IMAGE SETTING ............................................................................................................................... 35
5.4 ASPECT RATIO.................................................................................................................................. 38
5.5 PIP SETTING ..................................................................................................................................... 39
5.6 ANTI-BURN-IN ................................................................................................................................... 41
5.7 OSD SETTING ................................................................................................................................... 42
5.8 AUDIO SETTING................................................................................................................................ 43
5.9 SYSTEM............................................................................................................................................. 44
5.10 ECO SMART .................................................................................................................................... 46
5.11 INPUT SELECT ................................................................................................................................ 47
Chapter 6: Appendix
6.1 Warning Messages............................................................................................................................. 48
6.2 Troubleshooting.................................................................................................................................. 49
6.3 Transporting the LCD Display ............................................................................................................ 51
Chapter 7: Specications
7.1 Display Specications ........................................................................................................................ 52
7.2 Display Dimensions............................................................................................................................ 53
7.2.1 MX-22 Dimensions.................................................................................................................. 53
7.2.2 MX-24 Dimensions.................................................................................................................. 53

SAFETY INFORMATION
4
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to compl with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy, and if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

5
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries.
The symbol on the product or its packaging signies that this product has to be
disposed separately from ordinary household wastes at its end of life. Please
kindly be aware that this is your responsibility to dispose electronic equipment at
recycling centers so as to help conserve natural resources. Each country in the
European Union should have its collection centers for electrical and electronic
equipment recycling. For information about your recycling drop off area, please
contact your local related electrical and electronic equipment waste management
authority or the retailer where you bought the product.
Standard Test item Standard
EN60601-1-2:2007
RAD & CON EN55011(EMI)
Harmonic EN61000-3-2
Flicker EN61000-3-3
ESD IEC 61000-4-2: 2008
RS IEC 61000-4-3: 2006+A1:2007+A2:2010
EFT IEC 61000-4-4: 2012
Surge IEC 61000-4-5: 2005
CS IEC 61000-4-6: 2008
PFM IEC 61000-4-8: 2009
DIP IEC 61000-4-11: 2004

6
SAFETY INFORMATION
EMC Information
Essential performance of MX-22 and MX-24 is to display images and operate functions normally.
CAUTION
The MX-22 and MX-24 requires special precautions regarding EMC and need to be installed,put into service
and used according to the following information.
Do not use any cables other than the cables that provided or specied by us. Using other cables may
cause the increase of emission or decrease of immunity.
Do not put anyportable and mobileRF communications equipment close to the MX-22 and MX-24. Doing
so may affect the MX-22 and MX-24.
The MX-22 and MX-24 should not be used adjacent to or stacked with other equipment. If adjacent or
stacked use is necessary ,the equipment or system should be observed to verify normal operation in the
conguration in which it will be used.
Anyone who connects additional equipment to the signal input part or signal output parts,conguring a
medical system, responsible that the system complies with the requirements of IEC/ EN60601¬1¬2.
Guidance and manufacturer’s declaration – electromagnetic emissions
The MX-22 and MX-24 is intended for use in the electromagnetic environment specied below. The
customer or the user of the MX-22 and MX-24 should assure that it is used in such an environment. Not
Life-supporting Medical Equipment.
Emissions test Electromagnetic environment – guidance
Harmonic emissions
IEC/EN61000-3-2 Class A The MX-22 and MX-24 is suitable for use in all
establishments,including domestic establishments
and those directly connected to the public low-voltage
power supply network that supplies buildings used for
domestic pur poses.
Voltage uctuations /
icker emissions IEC/
EN61000-3-3
Class A

7
SAFETY INFORMATION
Guidance and manufacturer’s declaration – electromagnetic immunity
The MX-22 and MX-24 is intended for use in the electromagnetic environment specied below. The
customer or the user of The MX-22 and MX-24 should assure that it is used in such an environment.
Not Life-supporting Medical Equipment.
Immunity test IEC/EN60601
test level
Compliance level Electromagnetic environment –
guidance
Electrostatic
discharge (ESD)
IEC/EN61000-4-2
±6kV contact
±8kV air
±6kV contact
±8kV air
Floors should be wood, concrete
or ceramic tile. If oors are covered
with synthetic material, the relative
humidity should be at least 30%.
Electrical fast
transient / burst
IEC/EN61000-4-4
±2kV for power
supply lines
±1kV for input/output
lines
±2kV for power
supply lines
±1kV for input/output
lines
Mains power quality should be that
of a typical commercial or hospital
environment.
Surge
IEC/EN61000-4-5
±1kV line(s) to line(s)
±2kV line(s) to earth
±1kV line(s) to line(s)
±2kV line(s) to earth
Mains power quality should be that
of a typical commercial or hospital
environment.
Voltage uctuations /
icker emissions
IEC/EN61000-3-3
<5% UT (>95% dip in
UT) for 0.5 cycle
40% UT (60% dip in
UT) for 5 cycles
70% UT (30% dip in
UT) for 25 cycles
<5% UT (>95% dip in
UT) for 5 sec.
<5% UT (>95% dip in
UT) for 0.5 cycle
40% UT (60% dip in
UT) for 5 cycles
70% UT (30% dip in
UT) for 25 cycles
<5% UT (>95% dip
in UT) for 5 sec.
Mains power quality should be that
of a typical commercial or hospital
environment. If the user of the
MX-22 and MX-24 requires continued
operation during power mains
interruptions, it is recommended that
the MX-22 and MX-24 be powered
from an uninterruptible power supply
or a battery.
Power frequency
(50/60Hz) magnetic
eld
IEC/EN61000-4-8
3A/m 3A/m
Power frequency magnetic elds
should be at levels characteristic
of a typical location in a typical
commercial or hospital environment.
NOTE: UT is the a.c. mains voltage prior to application of the test level.
Mains power quality should be that of a typical commercial or hospital environment. If the user of the MX-22,
MX-24 requires continued operation during power mains interruptions, it is recommended that the MX-22
MX-24 be powered from an uninterruptible power supply or a battery.

8
SAFETY INFORMATION
ESD declaration statement
There are icker disturbance on the screen during the test, but auto recover after the test. This permissive
loss of performance is specied by the manufacturer, and this phenomena will be put as a clear statement in
the User’s Manual to avoid misunderstanding.
DIP declaration statement
The EUT power off during the test, but self- recover after the test. This permissive loss of performance is
specied by the manufacturer, and this phenomena will be put as a clear statement in the User’s Manual to
avoid misunderstanding.
Recommended separation distances between portable and mobile RF communications equipment
and the MX-22 and MX-24
The MX-22 and MX-24 is intended for use in an electromagnetic environment in which radiated RF
disturbances are controlled. The customer or the user of the MX-22 and MX-24 can help prevent
electromagnetic interference by maintaining a minimum distance between portable and mobile RF
communications equipment (transmitters) and the MX-22 and MX-24 as recommended below, according to
the maximum output power of the communications equipment.
Rated maximum output
power of transmitter (W)
Separation distance according to frequency of transmitter (m)
150kHz to 80MHz
d = 1.2 √ P
80MHz to 800MHz
d = 1.2 √ P
800MHz to 2.5GHz
d = 2.3 √ P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance
“d” in meters (m) can be estimated using the equation applicable to the frequency of the transmitter,
where “P” is the maximum output power rating of the transmitter in watts (W) according to the transmitter
manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected by
absorption and reection from structures, objects and people.
Cable length
Power Cord : Accessory 1.8m

9
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence
of a potential hazard that could
result in personal injury or damage
to the product.
ISO 7010-M002: Follow instructions
for use
This icon indicates important
operating and servicing
information.
This icon indicates complies with the
93/42/EEC, EN60601-1, EN 60601-1-2
of related European standards.
IEC 60417 -5009 : STAND- BY IEC 60417 -5031 : Direct Current
IEC 60417 -5032: Alternating
Current.
IEC 60417 -5021: Equipotentiality
Notice
• Read this User Manual carefully before using the LCD display and keep it for future reference.
• The product speci cations and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
http://www.agneovo.com.
• To register online, go to http://www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LCD display. Doing so may
affect the determination of the warranty period.

10
PRECAUTIONS
Cautions When Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject
to vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
Doing so may cause accidental re, electric shock or damage the LCD display.

11
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD
display.
The power outlet should be installed near the LCD
display and be easily accessible.
If an extension cord is used with the LCD display,
ensure that the total current consumption plugged
into the power outlet does not exceed the ampere
rating.
Do not allow anything to rest on the power cord. Do
not place the LCD display where the power cord
may be stepped on.
If the LCD display will not be used for an indenite
period of time, unplug the power cord from the
power outlet.
To disconnect the power cord, grasp and pull by the
plug head. Do not tug on the cord; doing so may
cause re or electric shock.
The mains plug or appliance coupler is used as
the disconnect device, the disconnect device
shall remain readily operable. Always completely
disconnect the power cord set from your product
whenever you are working or cleaning on it. Do not
make connections while the power is on, because
a sudden rush of power can damage sensitive
electronic components.
Do not unplug or touch the power cord with wet
hands.
Cleaning and Maintenance
Disconnect this equipment from any AC outlet before cleaning.
Do not use liquid or spray detergents for cleaning.
Use a damp cloth. Keeping to clean your monitor by monthly.
The LCD display comes with NeoVTM Optical Glass.
Use a soft cloth to clean the glass surface and the
housing. The display can be cleaned using a cloth
moistened with 95% ethyl alcohol.
Do not rub or tap the surface of the glass with sharp
or abrasive items such as a pen or screwdriver. This
may result in scratching the surface of the glass.
Do not attempt to service the LCD display yourself,
refer to qualied service personnel. Opening or
removing the covers may expose you to dangerous
voltage or other risks.
Warning:
Unplug the power cord
from the power outlet and
refer to qualied service
personnel under the following
conditions:
♦When the power cord is
damaged.
♦If the LCD display has been
dropped or the housing has
been damaged.
♦If the LCD display emits smoke
or a distinct odor.
Warning:
Ceiling mount or mount
on any other horizontal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizontal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

12
PRECAUTIONS
Notice for the LCD Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
• Adjust the LCD display to low brightness settings.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
When the LCD display is moved from one room to another or there is a sudden change from low to high
ambient temperature, dew condensation may form on or inside the glass surface. When this happens, do
not turn on the LCD display until the dew disappears.
Due to humid weather conditions, it is normal for mist to form inside the glass surface of the LCD display.
The mist will disappear after a few days or as soon as the weather stabilizes.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.
The intended use of the MX-22,MX-24 is to serve as a LCD monitor for integration with the hospital system.
It is designed for general purpose for adults using at hospital environment,continuous operation. For
displaying and viewing of images for reference. The use of this device does not require any direct contact
with patients.
Accessory equipment connected to the analog and digital interfaces must be in compliance with the
respective nationally harmonized IEC standards (i.e. IEC 60950 for data processing equipment, IEC 60065
for video equipment, IEC 61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
Furthermore all congurations shall comply with the system standard IEC 60601-1-1. Everybody who
connects additional equipment to the signal input part or signal output part congures a medical system,
and is therefore, responsible that the system complies with the requirements of the system standard
IEC 60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certied equipment in the patient
environment and IEC 60XXX certied equipment outside of the patient environment. If in doubt, consult the
technical services department or your local representative.
Grounding reliability can only be achieved when the equipment is connected to an equivalent receptacle
marked “Hospital Only” or “Hospital Grade”.

13
PRECAUTIONS
Notice for the LCD Display
Use a power cord that matches the voltage of the power outlet, which has been approved and complies
with the safety standard of your particular country.
The single device output analog signals through ADC element (Analog DigitalConvert) conversion to
become a digital signal and the video signal is via Video Decorder conversion. It has become the same
digital signal, these signals via Scaler IC as zoom in or out action and digital image processing, then
through the cable line transmission LVDS signals to one of the LCD module. The last by the clock controller
(Timing Controller, TCON), the clock signal is transmitted to the drive IC on the panel and turn on Backlight
for LCD module light source by Scaler control.
WARNING – No protection against the ingress of water : IPX0
WARNING – Do not modify this equipment without authorization of the manufacturer.
Installation and OSD adjusting should only be carried by manufacturer trained and authorized personnel.
WARNING – To avoid risk of electric shock, this equipment must only be connected to a supply mains with
protective earth.
CAUTION: This adapter Manufacturer/model is a forming part of the medical device.
♦Power by class I power supply.
♦Adapter manufacturer/model:.
ADAPTER TECH: ATM065-P120/ATM065T-P120
Input/output: 100-240V~50-60Hz, 12V( ) 5A.
EDAC TECH:EM10681G
Input/output: 100-240V~50-60Hz, 12V( ) 4.16A.
WARNING: Use suitable mounting apparatus to avoid risk of injury.
WARNING: The equipment not suitable for use in the presence of a ammable anesthetic mixture with air
or with oxygen or nitrous: Not AP or APG Category
CAUTION: No applied part.
Make sure the user not to contact SIP/SOPs and the patient at the same time.
CAUTION: Transport should only be undertaken in a at surface.

15
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents
When unpacking, check if the following items are included in
the package. If any of them is missing or damaged, contact your
dealer.
Quick Start Guide
Power cord
Note:
♦The pictures are for reference
only. Actual items may vary
upon shipment.
VGA cable
Power adapter
LCD Display
Audio cable
Note:
Must use only the supplied power
adapter:
♦Adaptor Technology
Model no.: ATM065-P120
Rating: 12V/5A
♦Adaptor Technology
Model no.: ATM065T-P120
Rating: 12V/5A
♦EDAC Technologies Corporation
Model no.: EM10681G
Rating: 12V/4.16A
Chapter 1: Product Description
Warranty card
MX-22 & MX-24
www.agneovo.com
MX-22/MX-24_Quick Guide_V010
Quick Start Guide
MX-22 & MX-24 LED-Backlit Display

16
PRODUCT DESCRIPTION
1.2 Wall Mounting Installation Preparation
1.2.1 Wall Mounting
1Remove the base stand.
See procedures below.
2Wall mount the LCD display.
Screw the mounting bracket to the VESA holes at
the rear of the LCD display.
100 mm
75 mm
100 mm 75
mm
1.2.2 Removing the Base Stand
1 Carefully place the
product screen side
down on a cushioned
surface that will
protect product and
screen from damage.
2 Remove the four
screws securing the
base stand from the
LCD display.
3 Detach the base
stand.
Note:
Take measures to prevent the
LCD display from falling down
and lessen possible injury and
damage to the display in case of
earthquakes or other disasters.
♦Use only the 75 x 75 mm and
100 x 100 mm wall mount kit
recommended by AG Neovo.
♦Secure the LCD display on a
solid wall strong enough to bear
its weight.
Note:
To protect the glass panel, place a
towel or soft cloth before laying the
LCD display down.
Warning:
Ceiling mount or mount
on any other horizontal
surface overhead are not
advisable.
Installation in contravention of
the instructions may result in
undesirable consequences,
particularly hurting people and
damaging property. Users who
have already mounted the
display on the ceiling or any
other horizontal surface overhead
are strongly advised to contact
AG Neovo for consultations and
solutions to help ensure a most
pleasurable and fullling display
experience.

17
PRODUCT DESCRIPTION
1.3 LCD Display Overview
1.3.1 Front View and Keypad Buttons
1
64 75 982 3
1Display screen
The LCD display screen is protected
by NeoVTM Optical Glass.
5UP
Hot Key: PIP Select
• Press repeatedly to select PIP option.
• During OSD menu selection, press to
move up a menu or submenu.
2AUTO
Hot Key: For VGA input signal
source, press to perform auto
adjustment.
• During OSD menu selection, press
to close the OSD menu or exit a
submenu.
6DOWN
Hot Key: DICOM Mode Select
• When PIP is on, press to SWAP the PIP
main and sub picture.
• When PIP is off, press to select picture
mode (STANDARD/DICOM)
• During OSD menu selection, press to
move down a menu or submenu.
3LEFT
Hot Key: Volume Down
• Press to display the volume screen.
Then press again to decrease the
volume.
• During OSD menu selection, press to
adjust the settings.
7MENU
• Press to display the OSD menu.
• Press again to hide the OSD menu.
8SOURCE
• Press to select the input signal source.
4RIGHT
Hot Key: Volume Up
• Press to display the volume screen.
Then press again to increase the
volume.
• During OSD menu selection, press
to select an option and adjust the
settings.
9POWER / LED indicator
• Press to turn the power on or off.
Green - Power on
Amber - Standby mode
Off - Power off

18
PRODUCT DESCRIPTION
1.3.2 Rear View
AUDIO INDVI HDMI DisplayPort VGA
DC IN
1
1DC power input
Use to connect the power cord.
4DisplayPort connector
Use to connect a PC using a DisplayPort
cable for digital input signal.
2DVI connector
Use to connect a PC using a DVI cable
for digital input signal.
5VGA connector
Use to connect a PC using a VGA cable for
analogue input signal.
3HDMI connector
Use to connect an input device using
an HDMI cable for digital input signal.
6Audio port
Use to connect an audio cable for the PC’s
audio input.
34 5 6
2

19
CHAPTER 2: MAKING CONNECTIONS
2.1 Connecting the Power
1Connect the power cord to the power adapter.
2Connect the power adapter to the DC power input at the rear of the LCD display.
3Connect the power cord plug to a power outlet or a power supply.
DC IN
Caution:
♦Make sure that the LCD display is
not connected to the power outlet
before making any connections.
Connecting cables while the power
is ON may cause electric shock or
personal injury.
Caution:
♦When unplugging the power cord,
hold the power cord by the plug
head. Never pull by the cord.
Chapter 2: Making Connections

20
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
2.2.1 Connecting a Computer
Using VGA Cables
Connect one end of a VGA cable to the VGA connector of the LCD display and the other end to the VGA
connector of the computer.
VGA
Using DVI Cables
Connect one end of a DVI cable to the DVI connector of the LCD display and the other end to the DVI
connector of the computer.
DVI

21
MAKING CONNECTIONS
Using DisplayPort Cables
Connect one end of a DisplayPort cable to the DisplayPort connector of the LCD display and the other end to
the DisplayPort connector of the computer.
DisplayPort
Using Audio Cables
Connect one end of an audio cable to the audio port at the rear of the LCD display and the other end to the
audio out port of the computer.
AUDIO IN