AGA CITY60 CONTEMPORARY User manual

05/15 EINS 516941
PLEA E READ THE E IN TRUCTION BEFORE COMMENCING ITE URVEY
OR IN TALLING THI APPLIANCE.
REMEMBER: when replacing a part on this appliance, use only spare parts that
you can be assured conform to the safety and performance specification that we
require. Do not use reconditioned or copy parts that have not been clearly autho-
rised by AGA.
For use in Australia
Installation
Guide
AGA CITY60 (CONTEMPORARY)
AGA CITY60 (TRADITIONAL)
AGA CITY60 TRADITIONALAGA CITY60 CONTEMPORARY

ECTION PAGE
HEALTH AND SAFETY 3
INSTALLATION REQUIREMENTS 3
REMOVAL FROM ALLET AND COOKER INSTALLATION 4 - 5
A LIANCE DIMENSIONS 6
CLEARANCES 7 - 8
OWER SU LY 9
MAINS CABLE ROUTING 10
CONTROL KNOB AND HANDRAIL CONNECTION 11
WIRING DIAGRAM 12
AGA CITY60 CHECKLIST 13
2
CONTENT

HEALTH AND AFETY
Consumer Protection
As responsible manufacturers we take care to make sure that our products are designed and constructed to meet the
required safety standards when properly installed and used.
PLEA E READ THE ACCOMPANYING WARRANTY
Any alteration that is not approved by AGA could invalidate the approval of the appliance, operation of the warranty and
could also affect your statutory rights.
IN TALLATION REQUIREMENT
THI APPLIANCE MU T ONLY BE IN TALLED BY COMPETENT ENGINEER WHO HAVE BEEN PECIFICALLY
FACTORY TRAINED ON THE PRODUCT AND WHO HAVE THE APPROPRIATE EQUIPMENT.
Installation must be to Local and National Wiring Regulations/Codes in force, and carried out by a Qualified Engineer.
roduct Approval for Australia to AS/NZ 560335.2.6.
3

REMOVAL FROM PALLET AND COOKER IN TALLATION
Fig. 1 DESN 516890
Removing of transit brackets - Unscrew 4 screws and
remove brackets, from front and two screws from rear.
Fig. 2 DESN 516891
NOTE: Care must be taken not to trap mains cable.
Appliance to be removed from rear of pallet
only.
Recess provided for suitable sack truck.
Appliance to be secured to sack truck with
suitable straps (shaded area)
Fig. 3 DESN 516892
Once appliance is in position in kitchen, remove sack
truck and straps. The front stability feet can be raised
with a spanner to allow appliance to be slid from transit
pallet.
STABILITY FOOT
MAINS
CABLE
Fig. 4 DESN 516893
Slide cooker off transit pallet. Take care not to trap
mains cable.
4

REMOVAL FROM PALLET AND COOKER IN TALLATION
Fig. 5 DESN 516894
Appliance can now be pushed back on its wheels into
desired position.
NOTE: Care must be taken not to trap mains cable.
Fig. 6 DESN 516895
Levelling of appliance - Use 13mm socket to adjust
wheel mechanism for FINE adjustment on both sides at
rear of the appliance.
Using a 12mm open end spanner, feet can be adjusted
at front to make FINE adjustments to the front of the
appliance and to provide a brake for the wheels.
Turning the bolt clockwise will lower the wheel thus
increasing height of the cooker.
Anti-clockwise lifts the wheels and lowers the cooker.
Fig. 7 DESN 516897
Fitting magnetic plinth
FRONT LINTH
COVER FITS
OVER SIDE SKIRTS
MAKE SURE SIDE
LINTH SKIRTS ARE
LOCATED IN FRONT
GUIDE BRACKET
Fig. 8 DESN 516898
Resting Plate Adjustment - Resting plates have
adjuster screw feet for setting of height and to improve
stability.
5

APPLIANCE DIMEN ION - AGA CITY60
Fig. 9 DESN 516872
APPLIANCE WEIGHT (Excludes Packaging)
Model: AGA CITY60 - 223kg
6

CLEARANCE
7
ide Clearances
If you are installing a AGA City60 in a new kitchen or have the opportunity to set the width between kitchen units, it is
advisable to include an additional small gap each side of 3mm to assist with installation and prevent damage when
moving the product.
A 6mm additional width clearance should also be provided if the cooker is to go into a brick recess, to allow for the wall
being out of square.
Where it is installed against a side wall protruding in the front of the cooker a 116mm clearance is required on the left hand
side for oven door access.
Fitting into a 60cm gap
If you are restricted to a 60cm width space, the AGA City60 will fit, subject to the following guide. lease refer to Fig. 9A.
The cooker top plate casting width tapers outwards at its bottom edge. Consequently adjacent cupboard units should have
a maximum depth of 595mm (including doors). If they are deeper, use the cooker rear spacer brackets to bring the cooker
forward. This will create a 25mm distance from the cooker front plate to cupboard doors.
The thickness of adjacent worktops should not exceed 45mm.
Cooker Base or Hearth
It is essential that the base or hearth on which the cooker stands should be level and be capable of supporting the total
weight of the appliance.
The front plinth cover is removable and must not be obstructed by flooring or tiles. If necessary the cooker must be raised
by the thickness of the tiles to ensure the plinth can be removed, and the cooker can be rolled out for service.
Tiling
When the cooker is to stand in a recess or against a wall which is to be tiled, in no circumstances should the tiles overlap
the cooker top plate, access to remove the top plate must be allowed for servicing at a later date.
Option Pre-heat Timer Kit (AE4M231659)
If the optional pre-heat timer kit is fitted allowances must be made for timer location and the cable between the timer and
cooker. Timer cable is 2.2 metres.
Fig. 9A DESN 516957

Combustible Rear Walls
Since this appliance can be used continuously, please take note of the IM ORTANT INSTRUCTIONS.
Where the rear wall is constructed of combustible materials (such as all-timber or stud wall partitions and batoned
plasterboard) these will require special wall heat protection measures.
Non-combustible insulation board as a protective cladding can be used behind the cooker of at least 15mm thick, such as
Monolux or equivalent. This should be taken up to hotplate level. See Fig. 9B.
Alternatively the cooker can be spaced away from the wall to create an air gap, using the 25mm spacer brackets supplied
with the cooker. See Fig. 9C.
The air gap must be left open and NOT blocked off across the top edge. See Fig. 9D.
Fig. 9B DESN 516959 DESN 516958
Fig. 9C
DESN 516960Fig. 9D
PECIAL NOTE: Ensure that unprotected electric cabling
or plastic services do not pass within or on the outside of
the wall behind or directly above the cooker. This type of
material can age prematurely when exposed to continuous
higher temperature.
Other Clearances
A minimum clearance of 60mm is required above the
raised insulating cover handle.
A minimum clearance of 1000mm must be available at the
front of the cooker to enable it to be serviced.
8

9
POWER UPPLY
WARNING: THI APPLIANCE MU T BE EARTHED.
THI APPLIANCE I DE IGNED FOR THE VOLTAGE TATED ON THE RATING PLATE, WHICH I ITUATED BEHIND
THE PLINTH COVER.
A 1 H 32 amp 230V or 3 H 400V minimum 16A per phase ~ 50 Hz fused electrical supply is required adjacent to the
appliance. External wiring to the unit must be installed using the mains cable provided, in accordance with the current wiring
regulations and any local regulations which apply. If cable is shortened, new ferrules must be fitted to the stripped
conductors.
The method of connection to the mains electricity supply must facilitate complete electrical isolation of the appliance, by a
multi-pole switch, having a contact separation of at least 3mm on all poles.
The isolator should not be positioned immediately above the cooker, but must be fitted within 2 metres of the appliance.
The isolator maybe separate from the connection point.
The mains connection point must be accessible within the areas shown in Fig 10, age 10 for cable routing options.
A fully recessed cooker connection box may be located immediately behind the cooker (in the hatched area only as shown
in Fig. 11), however the 25mm spacers (provided with the appliance) must be fitted.
For 2 or 3 phase installations an optional adaptor kit must be obtained ( art No. AE4M280352).

MAIN CABLE ROUTING
Fig. 10 DESN 516873
10
SECURE MAINS CABLE USING ‘ ’ CLI S FOR LEFT HAND OR RIGHT HAND
CABLE MANAGEMENT
NOTE: If timer kit is fitted use the cable tie provided in timer kit to secure timer cable to mains cable.
Fig. 11 DESN 516874 A
THE MAIN UPPLY MU T BE WITHIN THE ZONE HOWN
IF A RECE ED COOKER CONNECTION I TO BE U ED BEHIND THE
COOKER WITHIN THE HATCHED AREA. THE 25mm PACER PROVIDED
MU T BE FITTED
WORKTO
1.2 metres
1.2 metres