AgfaPhoto DC-1338i User manual

1
Thank you for purchasing this AGFAPHOTO digital camera. Please read these operating instructions
carefully in order to use the digital camera correctly. Keep the instructions in a safe place after reading so
that you can refer to them later.
Precautions
•Do not aim the camera directly into the sun or other intense light sources which could damage your
eyesight.
•Do not try to open the case of the camera or attempt to modify this camera in any way. High-voltage
internal components create the risk of electric shock when exposed. Maintenance and repairs should
be carried out only by authorized service providers.
•Do not fire the flash too close to the eyes of animals or people, especially for young children. Eye
damage may result. In particular, remain at least one meter away from infants when using flash.
•Keep the camera away from water and other liquids. Do not use the camera with wet hands. Never use
the camera in the rain or snow. Moisture creates the danger of electric shock.
•Keep the camera and its accessories out of the reach of children and animals to prevent accidents or
damage to the camera.
•If you notice smoke or a strange odor coming from the camera, turn the power off immediately. Take
the camera to the nearest authorized service center for repair. Never attempt to repair the camera on
your own.
•Use only the recommended power accessories. Use of power sources not expressly recommended for
this equipment may lead to overheating, distortion of the equipment, fire, electrical shock or other
hazards.
Disclaimer
We assume no responsibility over and above the provisions of the Product Liability Law for damages
suffered by the user or third parties as a result of inappropriate handling of the product or its accessories,
or by their operational failure and by their use. We reserve the right to make changes to this product and its
accessories without prior notice.
Warning!
Never try to open the camera or to take it apart. This will invalidate all guarantee claims. Danger of
explosion if batteries are not changed properly. Only replace the batteries with the same type or another
type approved by the manufacturer. Used batteries must be disposed of in accordance with the
manufacturer’s guidelines and local regulations.

2
Parts of the Camera
1. Stabilizer
2. Shutter Button
3. Operation Lamp
4. Power Button
5. Speaker
6. Self-timer Lamp / AF Lamp
7. Microphone
8. Lens
9. Flash
10. Zoom Button
11. Playback Button
12. Strap Ring
13. SET/DISP Button / Flash Button /
Macro Button
14. Mode Button
15. ASM Button / Delete Button
16. Menu Button
17. LCD Monitor
18. Battery Cover
19. USB/AV Terminal
20. Tripod Socket

3
Inserting the Batteries
Open the battery cover.
ySlide the battery cover in the
direction indicated by the arrow.
Insert the batteries.
yInstall the battery with the
terminal facing inside the camera.
Close the battery cover.
Inserting the Memory Card
Open the battery cover.
Insert the card.
yInsert the card with the label facing
up and the arrow pointing in.
yTo remove the card, gently press on the edge of the card and release it. Pull the card out
and close the battery cover.
Close the battery cover.
1
2
3
1
2
3
T
Ti ip ps s

4
Changing the Mode
You can record images and voices in the REC mode.And using the PLAYBACK mode to replay, delete,
or edit images on the LCD monitor.
Switching between REC mode and PLAYBACK mode
In REC mode: press the PLAYBACK button (n) to
switch to the PLAY mode.
In PLAY mode: press the PLAYBACK (n) or the
MODE (o) button to switch to the REC mode.
Selecting the REC mode
Set the camera to the REC mode.
Launch the mode palette.
yPress the MODE button to show the
scene mode palette.
Select a mode.
yUse the four-way control to select a desired mode and press the SET button to
confirm the setting.
Selecting the ASM mode
Set the camera to the REC mode.
yIt cannot be switch to ASM mode while in
Movie or Voice REC mode.
Launch the ASM mode.
yPress the ASM button (n) to toggle
switch between Aperture Priority, Shutter
Priority, Manual Exposure mode.
1
3
2
1
2

5
Using the Menus
When a menu is displayed, the four-way control and the SET button are used to make the desired
settings.
REC menu
Turn the power on, and set the camera
to the REC mode.
Open the REC menu.
yPress the MENU button to display the
menu.
Select an item.
yPress or to select a menu item.
Change the setting.
yPress or to change the setting.
Press the MENU or the SET button to save the settings and close the menu.
Setup menu
Turn the power on, and set the camera
to the REC or PLAYBACK mode.
Press the MENU button to open the REC
or PLAYBACK menu.
yThe menu displays depends on
whether you are in the REC mode or
the PLAY- BACK mode.
Open the Setup menu.
yPress four-way control to select SETUP ( ) and then press the SET button to
display the Setup menu.
4
5
3
1
2
3
1
2

6
Select an item.
yPress or to select a menu item and then press or the SET button to launch
the submenu.
Change the setting.
yPress or to select an option and press or the SET button to apply the
setting.
Press the MENU button to close the menu.
Using the Stabilizer
With more sensibility and faster shutter speed to bright up the pictures, effectively prevent blur image
caused by hand shack or target movement.
Playing Back Images
Turn the power on, and set the camera to the PLAYBACK mode.
yThe latest recorded image appears on the LCD monitor.
yIf there are no images stored, a message [No image] appears.
Press the four-way control or .
y: displays the previous image.
y: displays the next image.
4
5
6
1
2

7
Customer care
More information con the completeAGFAPHOTO digital camera product range can be found under
www.plawa.com
Service & Repair Hotline (EU):
00800 752 921 00 (from a landline only)
Service & Support Hotline (Germany):
0900 1000 042 (1.49 Euro/ min. from a German landline only)
Online Service / International contact:
[e-mail]
Manufactured by
plawa-feinwerktechnik GmbH & Co. KG
Bleichereistraße 18
73066 Uhingen
Germany
AGFAPHOTO is used under license of Agfa-Gevaert NV & Co. KG. Agfa-Gevaert NV & Co. KG. does
not manufacture this product or provide any product warranty or support. For service, support and
warranty information, contact the distributor or manufacturer. Contact: AgfaPhoto Holding GmbH,
www.agfaphoto.com
Disposal of Waste Equipment by Users in Private Households in the European Union
This symbol on the product or on its packaging indicates that this product must not be disposed of with
your other household waste. Instead, it is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will
help to conserve natural resources and ensure that it is recycled in a manner that protects human
health and the environment. For more information about where you can drop off your waste
equipment for recycling, please contact your local city office, your household waste disposal service
or the shop where you purchased the product.

8
Batteries and rechargeable batteries should not be thrown in the trash can. Please return used
batteries to the store or take it to where they collets such items. Following this guideline we are
helping not to polluting our environment.
Declaration of Conformity
We herewith confirm the following designated product: AGFAPHOTO digital camera DC-1338i has
been tested and found to comply with the requirements set up in the council directive on the
approximation of the law of members’ states relating to the EMC Directive 2004/108/EC.
For the evaluation regarding to the electromagnet compatibility, the
following standards were applied
EN 55022:2006, Class B
IEC 61000-3-2:2005
IEC 61000-3-3:2005
EN 55024:1998+A1:2001+A2:2003
IEC 61000-4-2:2001
IEC 61000-4-3:2006
IEC 61000-4.4: 2004
IEC 61000-4-5:2005
IEC 61000-4-6:2006
IEC 61000-4-8:2001
IEC 61000-4-11:2004
The device is marked with CE Logo.
FCC Compliance and Advisory
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1.) this device may not cause harmful interference, and 2.) this device must accept any
interference received, including interference that may cause unsatisfactory operation. This equipment
has been tested and found to comply with the limits for a Class B peripheral, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.

9
•Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected.
•Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment. When shielded interface cables have been
provided with the product or when specified additional components or accessories have elsewhere
been designated to be used with the installation of the product, they must be used in order to ensure
compliance with FCC regulations.