Agilent Technologies U2300A Series User manual

Agilent Technologies
Agilent U2300A Series
USB Multifunction Data
Acquisition Devices
User’s Guide

II U2300A Series DAQ User’s Guide
Notices
© Agilent Technologies, Inc., 2006–2009
No part of this manual may be reproduced in
any form or by any means (including elec-
tronic storage and retrieval or translation
into a foreign language) without prior agree-
ment and written consent from Agilent
Technologies, Inc. as governed by United
States and international copyright laws.
Manual Part Number
U2351-90002
Edition
Fourth Edition, 1September 2009
Printed in Malaysia
Agilent Technologies, Inc.
Bayan Lepas Free Industrial Zone,
11900 Penang, Malaysia
Trademark Acknowledgements
Pentium is a U.S. registered trademark of
Intel Corporation.
Microsoft, Visual Studio, Windows, and MS
Windows are trademarks of Microsoft Cor-
poration in the United States and/or other
countries.
Warranty
The material contained in this docu-
ment is provided “as is,” and is sub-
ject to being changed, without notice,
in future editions. Further, to the max-
imum extent permitted by applicable
law, Agilent disclaims all warranties,
either express or implied, with regard
to this manual and any information
contained herein, including but not
limited to the implied warranties of
merchantability and fitness for a par-
ticular purpose. Agilent shall not be
liable for errors or for incidental or
consequential damages in connec-
tion with the furnishing, use, or per-
formance of this document or of any
information contained herein. Should
Agilent and the user have a separate
written agreement with warranty
terms covering the material in this
document that conflict with these
terms, the warranty terms in the sep-
arate agreement shall control.
Technology Licenses
The hardware and/or software described in
this document are furnished under a license
and may be used or copied only in accor-
dance with the terms of such license.
Restricted Rights Legend
U.S. Government Restricted Rights. Soft-
ware and technical data rights granted to
the federal government include only those
rights customarily provided to end user cus-
tomers. Agilent provides this customary
commercial license in Software and techni-
cal data pursuant to FAR 12.211 (Technical
Data) and 12.212 (Computer Software) and,
for the Department of Defense, DFARS
252.227-7015 (Technical Data - Commercial
Items) and DFARS 227.7202-3 (Rights in
Commercial Computer Software or Com-
puter Software Documentation).
Safety Notices
CAUTION
A CAUTION notice denotes a haz-
ard. It calls attention to an operat-
ing procedure, practice, or the like
that, if not correctly performed or
adhered to, could result in damage
to the product or loss of important
data. Do not proceed beyond a
CAUTION notice until the indicated
conditions are fully understood and
met.
WARNING
A WARNING notice denotes a
hazard. It calls attention to an
operating procedure, practice, or
the like that, if not correctly per-
formed or adhered to, could result
in personal injury or death. Do not
proceed beyond a WARNING
notice until the indicated condi-
tions are fully understood and
met.

U2300A Series DAQ User’s Guide III
Safety Information
The following general safety precautions must be observed during all phases of this instrument. Failure to comply
with these precautions or with specific warnings elsewhere in this manual violates safety standards of design,
manufacture, and intended use of the instrument. Agilent Technologies, Inc. assumes no liability for the
customer’s failure to comply with these requirements.
Safety Symbols
The following symbols indicate the precautions taken to maintain safe operation
of the instrument.
Regulatory Markings
Direct current
Warning
The CE mark shows that the product complies with all the
relevant European Legal Directives (if accompanied by a year, it
signifies when the design was proven).
The CSA mark is a registered trademark of the Canadian Stan-
dards Association. A CSA mark with the indicators "C" and "US"
means that the product is certified for both the U.S. and Canadian
markets, to the applicable American and Canadian standards.
The UL Mark is a registered trademark of Underwriters Laborato-
ries Inc. UL listing mark with the indicators "C" and "US” indi-
cates the product compliance with both Canadian and U.S.
requirements.
The C-tick mark is a registered trademark of the Spectrum Man-
agement Agency of Australia. This signifies compliance with the
Australian EMC Framework regulations under the terms of the
Radio Communications Act of 1992.

IV U2300A Series DAQ User’s Guide
General Safety Information
WARNING
• Do not use the device if it is damaged. Before you use the device,
inspect the case. Look for cracks or missing plastic. Do not operate the
device around explosive gas, vapor, or dust.
• Do not apply more than the rated voltage (as marked on the device)
between terminals, or between terminal and external ground.
• Always use the device with the cables provided.
• Observe all markings on the device before connecting to the device.
• Turn off the device and application system power before connecting to
the I/O terminals.
• When servicing the device, use only specified replacement parts.
• Do not operate the device with the removable cover removed or
loosened.
• Do not connect any cables and terminal block prior to performing
self-test process.
• Use only the power adapter supplied by the manufacturer to avoid any
unexpected hazards.
CAUTION
• Do not load the output terminals above the specified current limits.
Applying excessive voltage or overloading the device will cause
irreversible damage to the circuitry.
• Applying excessive voltage or overloading the input terminal will
damage the device permanently.
• If the device is used in a manner not specified by the manufacturer, the
protection provided by the device may be impaired.
• Always use dry cloth to clean the device. Do not use ethyl alcohol or
any other volatile liquid to clean the device.
• Do not permit any blockage of the ventilation holes of the device.

U2300A Series DAQ User’s Guide V
Waste Electrical and Electronic Equipment (WEEE) Directive
2002/96/EC
This instrument complies with the WEEE Directive (2002/96/EC) marking
requirement. This affixed product label indicates that you must not discard this
electrical/electronic product in domestic household waste.
Product Category:
With reference to the equipment types in the WEEE directive Annex 1, this
instrument is classified as a “Monitoring and Control Instrument” product.
The affixed product label is shown as below:
Do not dispose in domestic household waste
To return this unwanted instrument, contact your nearest Agilent office, or visit:
http://www.agilent.com/environment/product
for more information.

VI U2300A Series DAQ User’s Guide
In This Guide...
1 Getting Started provides an overview of the U2300A Series, the product outlook,
product dimension, and product layout. This chapter also contains the
instructions on getting started with the U2300A Series from system requirements
checking to installations of hardware and software to the launching of the Agilent
Measurement Manager application software.
2 Connector Pins Configuration describes the connector pins configuration of
the U2300A Series USB DAQ and the signal connection between the U2300A and
external devices.
3 Features and Functions includes the information for better understanding on
the features and functions of the U2300A series USB DAQ. This includes the
operations of the analog input, analog output, digital input/output, and digital
counter subsystems.
4 Characteristics and Specifications specifies the characteristics,
environmental conditions, and specifications of the U2300A DAQ devices.
5 Calibration introduces the procedures to perform the calibration process for the
U2300A Series DAQ devices to minimize A/D measurement errors and D/A
output errors.

U2300A Series DAQ User’s Guide VII
DECLARATION OF CONFORMITY
According to ISO/IEC Guide 22 and CEN/CENELEC EN 45014
Generic example
Manufacturer’s Name: Agilent Technologies Microwave Products (M) Sdn. Bhd
Manufacturer’s Address: Bayan Lepas Free Industrial Zone,
11900, Bayan Lepas, Penang, Malaysia
Declares under sole responsibility that the product as originally delivered
Product Name: Agilent U2300A Series Multifunction USB Data
Acquisition(DAQ) device
Models Number: U2331A, U2351A, U2352A, U2353A, U2354A, U2355A,
U2356A
Product Options: This declaration covers all options of the above product(s)
complies with the essential requirements of the following applicable European Directives, and
carries the CE marking accordingly:
Low Voltage Directive (73/23/EEC, amended by 93/68/EEC)
EMC Directive (89/336/EEC, amended by 93/68/EEC)
and conforms with the following product standards:
EMC Standard
StandardStandard
Standard
Limit LimitLimit
Limit
IEC 61326-1:1997+A1:1998 / EN 61326-1:1997+A1:1998
CISPR 11:1990 / EN55011:1991 Class A Group 1
IEC 61000-4-2:1995+A1:1998 / EN 61000-4-2:1995 4 kV CD, 8 kV AD
IEC 61000-4-3:1995 / EN 61000-4-3:1995 3 V/m, 80-1000 MHz
IEC 61000-4-4:1995 / EN 61000-4-4:1995 0.5 kV signal lines, 1 kV power lines
IEC 61000-4-5:1995 / EN 61000-4-5:1995 0.5 kV line-line, 1 kV line-ground
IEC 61000-4-6:1996 / EN 61000-4-6:1996 3 V, 0.15-80 MHz
IEC 61000-4-11:1994 / EN 61000-4-11:1994 1 cycle / 100%
Canada: ICES-001:1998
Australia/New Zealand: AS/NZS 2064.1
The product was tested in a typical configuration with Agilent Technologies test systems.
Safety IEC 61010-1:2001 / EN 61010-1:2001
Canada: CSA C22.2 No. 61010-1:2004
USA: UL 61010-1: 2004
This DoC applies to above-listed products placed on the EU market after:
20-October-2006
Date Mack Soh
Quality Manager
For further information, please contact your local Agilent Technologies sales office, agent or distributor,
or Agilent Technologies Deutschland GmbH, Herrenberger Straße 130, D 71034 Böblingen, Germany.
Template: A5971-5302-2, Rev. B.01 U2300 series Rev 1.0

VIII U2300A Series DAQ User’s Guide
Product Regulations
Performance Criteria
IEC 61326-1:1997+A1:1998 / EN 61326-1:1997+A1:1998 U2331A, U2351A, U2352A U2353A,
U2354A, U2355A, U2356A
CISPR 11:1990 / EN 55011:1991 – Group 1 Class A
IEC 61000-4-2:1995+A1:1998 / EN 61000-4-2:1995 (ESD 4kV
CD, 8kV AD)
B
IEC 61000-4-3:1995 / EN 61000-4-3:1995 (3V/m, 80% AM) A
IEC 61000-4-4:1995 / EN 61000-4-4:1995 (EFT 0.5kV line-line,
1kV line-earth)
B
IEC 61000-4-5:1995 / EN 61000-4-5:1995 (Surge 0.5kV line-line,
1kV line-earth)
B
IEC 61000-4-6:1996 / EN 61000-4-6:1996 (3V, 0.15~80 MHz,
80% AM, power line)
A
IEC 61000-4-11:1994 / EN 61000-4-11:1994 (Dips 1 cycle,
100%)
C
Canada: ICES-001:1998
Australia/New Zealand: AS/NZS 2064.1
EMC
IEC 61010-1:2001 / EN 61010-1:2001
Canada: CSA C22.2 No. 61010-1:2004
Safety
USA: UL 61010-1: 2004
Additional Information:
The product herewith complies with the essential requirements of the Low Voltage Directive 73/23/EEC and the
EMC Directive 89/336/EEC (including 93/68/EEC) and carries the CE Marking accordingly (European Union).
1
Performance Criteria:
A Pass - Normal operation, no effect.
B Pass - Temporary degradation, self recoverable.
C Pass - Temporary degradation, operator intervention required.
D Fail - Not recoverable, component damage.
N/A – Not applicable
Models Description:
U2331A – USB 64SE/32DI, 12bits, 3MSa/s Multifunction USB DAQ
U2351A – USB 16SE/8DI, 16bits, 250kSa/s Multifunction USB DAQ
U2352A – USB 16SE/8DI, 16bits, 250kSa/s Multifunction USB DAQ (without Analog output)
U2353A – USB 16SE/8DI, 16bits, 500kSa/s Multifunction USB DAQ
U2354A – USB 16SE/8DI, 16bits, 500kSa/s Multifunction USB DAQ (without Analog output)
U2355A – USB 64SE/32DI, 16bits, 250kSa/s Multifunction USB DAQ
U2356A – USB 64SE/32DI, 16bits, 500kSa/s Multifunction USB DAQ
Notes:
Regulatory Information for Canada
ICES/NMB-001:1998
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est confomre à la norme NMB-001 du Canada.
Regulatory Information for Australia/New Zealand
This ISM device complies with Australian/New Zealand AS/NZS 2064.1

U2300A Series DAQ User’s Guide IX
Contents
1Getting Started
Introduction 2
Product Overview 3
Product outlook 3
Product dimension 4
Standard Purchase Items Checklist 6
Software Installation 7
A. Check Your System Requirements 8
B. Install the Agilent IO Libraries Suite 9
C. Install the Hardware Driver 10
D. Install the Agilent Measurement Manager 13
E. Connect Your Device to the PC 17
F. Launch Your Agilent Measurement Manager 20
L-Mount Kit Installation 21
General Maintenance 23
2Connector Pins Configuration
Connector Pins Configuration 26
Analog Input Signal Connection 33
Types of signal sources 33
Input configurations 34

X U2300A Series DAQ User’s Guide
Contents
3Features and Functions
Features Overview 40
Analog Input Operation Mode 41
Scan list (for continuous mode only) 45
Burst mode 46
A/D data conversion 47
AI data format 49
Analog Output Operation Mode 51
D/A reference voltage 55
AO data format 55
Digital I/O 58
General Purpose Digital Counter 61
Trigger Sources 67
Trigger types 68
Digital trigger 71
Analog trigger 72
SCPI Programming Examples 75
Analog input 75
Analog output 78
4Characteristics and Specifications
Product Characteristics 82
Product Specifications 83
Basic multifunction DAQ device specifications 83
High density multifunction DAQ device specifications 87
Electrical Measurement Specifications 91
Basic multifunction USB DAQ device specifications 91
High density multifunction USB DAQ device specifications 93