AGRI-COVER SRT-2 Quick start guide

To view an installation video of an SRT-2 tarp - visit www.agricover.com/rolltarps/videos/
SRT-2®HAND AND ELECTRIC INSTALLATION
INSTRUCTIONS AND OWNERS MANUAL

TROUBLE SHOOTING . . . . . . . . . . . . . . . . . . . . . . 21
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . Back Cover

stainless steel bolt in for attachment.

A. WEATHER SEAL
Note: Some kits do
not include weather
seal, if weather seal
is not included in kit
procede to step 1B.
Clean underside of cap
for adhering weather
seal. Repeat on each
end of front and rear
end cap.

Note: For grain carts with an outturned top rail use optional offset
base bracket. See optional offset base bracket illustration.
STEP 3: QUICK RELEASE TARP BRACKETS
ILLUSTRATION 8
INSTALLATION INSTRUCTIONS
A. QUICK RELEASE TARP
STOP These brackets secure the
stationary side of the tarp to the
box. For normal applications,
place brackets on PASSENGER
side of box. For reverse roll, place
brackets on DRIVER side of the
box. Place rst and last tarp stop
preferably 11” in from air dam.
Attach brackets to outside of box
so top of bracket is 1/4” down
from top of box.
Drill two 5/16” holes and use two
3/8” x 1” self threading screws to
mount each bracket.
Then assemble trap stop to bracket
with lower clevis pin and bow tie
pin. This leaves bracket in its open
position to receive the tarp tube.
See Illustration 8 and 9. VIEW AT TOP FRONT CORNER OF BOX (passenger side)
Drill 5/16” Holes
and Use 4 3/8” Self
Threading Screws For
First and Last Bracket
Use (2) 3/8” x 1” Self
Threading Bolts For
All Interior Brackets
Tarp Stop
Base Bracket
Bow Tie
Pins
10” From
Air Dam
1/4”
Clevis Pins
1/4”

B. QUICK RELEASE BRACKETS Position these
brackets evenly between front and rear tarp stops. See
“EXAMPLE” below and Illustration 9. Then assemble
quick release bracket with lower clevis pin and bow tie pin.
Use (2) 3/8” x 1” self
thread screws with lock
washer and nuts.
Use (2) 3/8” x 1” self thread
screws - drill 5/16” holes
preferably in middle pair of
slotted holes on bracket.
Offset base bracket
Tarp stop
base bracket
Drill 5/16” holes and
use (2) 3/8” x 1” self
thread screws with
lock washer and nuts.
OPTIONAL OFFSET BASE BRACKET
EXAPMLE:
11 11
ILLUSTRATION 9

Left
A. FRONT SPOOL (BLACK) Is marked with an
L (left) to match with black (unpainted) spring and
black (unpainted) end of roll tube. Start assembly
by sliding a rubber ring (serves as a seal) onto the
roll tube. Insert the offset tab end of the black spring
into the L spool so its tab extends through small
hole. Slide spring with spool over black end of roll
tube until cartridge tube extends through center of
spool. To ensure spring fully engages in tube, turn
spool COUNTER CLOCKWISE about an inch
and push. Slide PVC spacer on up against spool,
align holes to fasten with 5/16 x 1-3/4” bolt and
lock nut. See Illustration 12.
NOTE: For detailed views of front and rear
springs refer to parts diagram on page 18.
NOTE: If you are installing a hand crank tarp,
tighten PVC spacer bolt on the front end now.
If you are installtion and electric tarp, leave this
bolt loose for removal in step 12, page 14.

Apply Ratchet Decal
Next to Installed
Ratchet