Agus V-Board 5560600200 User manual

1
RANGER

WARRANTY
2 YEARS
EQUIPMENT LIST
▪Protective glasses
▪Ratchet wrench and
arms
▪Cable stripper
▪Allen wrench set
▪Electrical insulating
strap
▪Pliers
▪8 mm spanner
▪13 mm spanner
▪10 mm spanner
▪Drill
2
1234
INSTALLATION TIME
3 –4 HOURS
Professional installation
recommended
DIFFICULTY LEVEL

-Parts
Motorized Center Carrier
Foot
3
LED
Control Unit
Front Carrier Foot Rear Carrier Foot
Board

- Connection Parts
Board profile connection part x 2 M6 x 20 hex socket head bolt x 4
4
M10 x 25 Flanged (Wrench flat 13mm) Bolt x 6 Pieces
Note: If the vehicle has a fixed board, its original connecting bolt is
used.

-Electrical Diagram and Components
5
TWIN ENGINED v - board
*** It is not used in Ford
Ranger models.
Back view
Front Engine Socket
Main Engine Socket
Rear Engine Socket
Additional Engine Socket
Front Lightening
Socket
Rear Lightening
Socket

- Wiring Assembly
6
Front Door Switch Connection
Rear Door Switch Connection
Fuse 20A
- Speed information connection.( Optional )–J2
- ( + 12 V ) Step open signal connection ( Optional )- J3
(Fuse 20A)
(+12V Feeder)
(Red-White)
(Fuse 25A)
(Brown)
Center Door Switch
J6 –Orange-Switch
J7 –Brown - GND
Front Door Switch
J13-White-Switch
J12-Brown-GND

- Wiring Assembly
7
LED –1 connection
Front Engine Socket
LED –2 connection
Rear Engine Socket
***It is not used in Ford
Ranger models.
Front Lightening Socket
Rear Lightening Socket
Front Engine Socket
Rear Engine Socket

- Wiring Assembly LEFT
Before starting installation, the fuse on the wiring is
removed. !!!!
Connect the plus ( + ) end of the wiring to the plus
( + ) end of the battery.
8
1
Connect the minus ( - ) end of the wiring
to the chassis of the vehicle.
2
**** !!! S1 fuse on the wiring
**** !!! Tip J4 on the installation.
Left side v_Board installation, wiring and
control unit connection is made on the
driver side, in the area shown in the
picture.
Note: The area with the original sockets on
the left side of the pedals.
**** !!! Before connecting the control unit, remove
fuse S2 on the wiring.
The (+) end of the installation is pulled from the
section shown in the picture ( the lower part of the
steering wheel of the vehicle) to the battery
section on the front of the vehicle ( it must be
passed through the rubber stopper).
3
4
(+12V Feeder)
(Red-White)
S1
(Fuse –25A)

- Wiring Assembly LEFT
9
5
From the original hole of the vehicle
located under the driver's mat, the engine
and LED ends of the left v_Board wiring are
extended to the bottom of the vehicle as
shown in the picture. 6
The battery connection of the (+) end of the wiring
is made as shown in the picture.

- Wiring Installation RİGHT
Before starting installation, the fuse located on the
wiring is removed. !!!!
Connect the plus ( + ) end of the wiring to the plus
( + ) end of the battery.
10
1
Connect the minus ( - ) end of the wiring
to the chassis of the vehicle.
2
**** !!! S1 fuse on the wiring.
**** !!! Tip J4 on the wiring.
Right side v-Board installation, wiring and
control unit connection is made in the
area shown in the picture on the front
passenger side.
Note: The section with the original sockets
located on the lower right side of the
torpedo.
**** !!! Before connecting the control
unit, remove fuse S2 on the wiring.
The end of the installation (+) must be passed
through the part shown in the picture ( the lower
part of the steering wheel of the vehicle) inside the
vehicle ( rubber stopper ) is pulled towards the
battery section at the front.
3
4
(12V Feeder)
(Red-White)
(Fuse-25A)

- Wiring Assembly LEFT
11
5
From the original hole of the vehicle
located under the driver's mat, the engine
and LED ends of the left v_Board
installation are extended to the bottom of
the vehicle as shown in the picture.
6
The battery connection of the (+) end of the wiring
is made as shown in the picture.

- Mechanical Assembly
12
In the installation of carriers on the board, the board profile
connection parts are movable in the board channel. By sliding the
carrier foot to the installation section, the board is assembled
together with the carrier foot.

13
1
The vehicle's original chassis hole is
used for the front carrier foot
connection.
Note: M10 AA=13mm bolts are used on
the vehicle in assembly processes.
- Mechanical Assembly

14
2
The vehicle's original chassis hole is
used for the middle carrier foot
connection.
Note: M10 AA=13mm bolts are used
on the vehicle.
- Mechanical Assembly

15
2
The vehicle's original chassis hole is
used for the center carrier foot
connection.
Note: M10 AA=13mm Bolts are used on
the vehicle in assembly processes.
- Mechanical Assembly

16
3
The vehicle's original chassis hole is
used for rear carrier foot connection.
Note: M10 AA=13mm bolts are used on
the vehicle in assembly processes.
- Mechanical Assembly

17
4
As shown in the figure, the board is placed on the carrier foots and
installed with M6 x 20 hex socket head bolt from the bottom side.
- Mechanical Assembly

- LED Assembly
18
For LED installation, a Ø10 mm hole is drilled
with a drill near the connection point of the
carrier. 1
LED cables are passed through the drilled
hole.
2
4
LED cable connections are made. LED
assembly is completed.
3
For the passage of the LED cable, the hole
drilled by a Ø10 mm drill is cut as shown in
the figure with the help of an air saw.

19
Check the operation of the v –board, opening and closing. Check
that the LED light is lit when the door is opened.
When starting installation, replace the fuse
that we have removed from the
installation. After replacing the fuse, check
the operation of the v-board.
- Final Control
5
**** !!! Replace fuse S1
**** !!! Make sure that the fuses S1 and S2 are
installed in the correct place in the installation.

- Wiring Assembly_Addition
20
Electrical connections for On & Off position
information of right front door.
The plastic cover under the right front
torpedo, where the vehicle's original signal
sockets were located, is removed.
The white cable in the v_Broard wiring is
connected to the white cable in the original
wiring of the vehicle as shown in the picture.