Aicok KE7466T-GS User manual

KETTLE
INSTRUCTION MANUAL
KE7466T-GS
READ THIS BOOKLET THOROUGHLY
BEFORE USING AND SAVE IT FOR FUTURE REFERENCE

IMPORTANT SAFETY INSTRUCTIONS
1. Read all instructions before using.
2. Before connecting the kettle to the power supply,
check that the voltage indicated on the appliance
(underside the kettle & base) corresponds with the
voltage in your home. If this is not the case, contact
your dealer and do not use the kettle.
3. The attached base can not be used for other than
intended use.
4. Do not operate the appliance without load to avoid
damaging the heat elements.
5. Unplug from the outlet when not in use.
6. Do not let the cord hang over edge of table counter
or touch hot surface.
7. Do not place on or near a hot gas or electric burner
or in a heated oven.
8. Should you accidentally allow the kettle to operate
without water, the boil-dry protection will automatically
switch it off. If this should occur, allow the kettle to cool
before filling with cold water and re-boiling.
9. Ensure that kettle is used on a firm and flat surface
where the children can’t touch, this can prevent from
overturning the kettle to damage the person or kettle.
10.To protect against a fire, electric shock or personal
injury, do not immerse cord, electric plugs or kettle in
water or other liquids.
11.Always take care to pour boiling water slowly and
carefully without tipping the kettle too fast.
-1-

12.Be careful when opening the lid for refilling when
thekettleishot.
13.Close supervision is necessary when any appliance
is used by or near children.
14.Do not touch the hot surface. Use the handle or the
button.
15.Extreme caution must be used when moving an
appliance containing hot water.
16.The appliance is not a toy. Do not let the children
play it.
17.The use of attachments that are not recommended
by the appliance manufacturer may result in fire,
electric shock or personal injury.
18.While boiling water, avoid to contacting steam from
the spout when water is boiling or just after it has
switched off. Do not be anxious to uncover the lid.
19.Unplug from outlet when not in use and before
cleaning;Allow it to cool before putting on or taking off
parts and before cleaning the appliance.
20.Always ensure the lid is closed and do not lift it
while the water is boiling. Scalding may occur if the lid
is removed during the brewing cycles.
21.If the supply cord is damaged, it must be replaced
by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
22.Do not use the appliance for other than intended
use.
23.Do not move the unit while the kettle is switched on.
-2-

24.The kettle can only use with the stand provided.
25.If the kettle is overfilled, boiling water may be
ejected.
26.Do not use the kettle outdoors.
27.This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliances by a
person responsible for their safety.
28.Children should be supervised to ensure that they
do not play with the appliance.
29.This appliance is intended to be used in household
and similar applications such as:
– Staff kitchen areas in shops, offices and other
working environments;
– Farm houses;
– By clients in hotels, motels and other residential
type environments;
– Bed and breakfast type environments.
30.Save these instructions.
31.This appliance has been incorporated with a
grounded plug. Please ensure the wall outlet in your
house is well earthed.
-3-

K
now
y
our
k
ett
l
e
BASE
WATER GAUGE
HANDLE
BODY
SPOUT LID LID BTTTON
ON/OFF
SET KEY
KEEP WARM KEY
TEMPERATURE INDICATOR LIGHT
Before initial use
If you are using the kettle for the first time, it is recommended
that you clean your kettle before use by boiling a full kettle of
water twice and then discarding the water.
-4-

Operation
1. To fill water into the kettle, remove it from the power base and
open the lid by press down the lid button, fill with the desired
amount of water to the kettle. Always fill the kettle between the
minimum (0.5L) and maximum (1.7L) marks. Too little water will
result in the kettle switching off before the water has boiled.
NOTE: Do not fill the water over the maximum level, as
water may spill out of the spout when boiling. Ensure that
the lid is firmly in place before connecting the power cord
to the outlet.
2. Close the lid. Position the kettle on the power base in place.
Make sure the kettle contact with the power base completely.
3. Function buttons
3.1Function instruction
This is a full automatic electronic control kettle. It can boil water
to the setting temperature and keep warm. The function buttons
are designed on the handle, include ON/FF button, “SET” button,
“KEEP WARM”button, LED indicating water temperature and
working model, include one ON/OFF indicator light, one keep
warm indicator light, 6 temperature setting light ,such as “40ć”ǃ
“60ć”ǃ “70ć”ǃ “80ć”ǃ “90ć”ǃ “100ć”.Press down the ON/OFF
-5-

button, the red indicator light on button bright, and indicating
power on. When boiling water, the red indicator light under the
setting temperature bright, and indicating which temperature you
are setting. When product in the keep warm status, the red
indicator light on the “KEEP WARM” button bright. After keep
warm for a half hour, product will auto-shut off,or just to press
the ON/OFF button to shut off the kettle. Product with memory
function .
3.2 Electronic control program and operation instruction:
3.2.1. Fill appropriate water (0.5L~1.7L), energize product to
make it standby, at this moment, all indicator light is not bright.
3.2. 2Press ON/OFF button, the red indicator light in ON/OFF
button and 100ćsetting button bright. If do not select the
water temperature button, product will gives tacit consent to
boil the water to 100°C. After water boil, power auto-shut off
without warm keeping function, all indicator light off.
3.2.4. In energizing status, user could select the temperature of
“40ć”ǃ“60ć”ǃ“70ć”ǃ“80ć”ǃ“90攓100ć”circularly by
pressing the button of “set”ˈindicator light bright on according to
the button has been selected. The interval between two buttons
pressing is 3s, if the interval is less than 3s, the selection is out
of effective. Program will treat the last selection as the
temperature request. When the water have not reach the setting
-6-

temperature, kettle will start to heat up till reach the request
temperature and then automatically stop working, all indicator
light shut off and also power auto-shut off.
3.2.5. During kettle in item 3.2/3.3 working state, press down the
“keep warm” button to start the keep warm function, indicator for
“keep warm” button bright. The keep warm temperature is the
temperature has been setting. When the water in kettle reach
the setting temperature, the “keep warm” indicator light bright up,
remind you product has turned to keep warm state. The warm
keeping time is half hour. After half hour, product power
auto-shut off, also the indicator light. Remark: product
auto-energized the “keep warm” function when temperature
setting in 100ć.And the “keep warm” function is begun when
water temperature reduce to 90ć(indicator light off when water
reach 100ć, indicator light on again when water in 90ć), warm
keeping last for a half hour.
3.2.6.After “keep warm” function energized, if press the “keep
warm” button at this moment, keep warm setting will be
cancel, and the indicator light shut off. Come to program
3.3
3.2.7. In product energizing state, press down the ON/OFF
-7-

button, product will be shut off, re-press this
Button, product is re-energized.All setting before will be invalid.
3.2.8. Kettle with memory function. When kettle was taken away
from power base and was put back within 90 seconds, the keep
warm function still works (no need to reset the progress).
Boil-dry protection
Should you accidentally allow the kettle to operate without water,
the boil-dry protection will automatically switch it off. If this
should occur, allow the kettle to cool before filling with cold water
and re-boiling.
Care and cleaning
Always disconnect the appliance from the power outlet and
leave it to cool down completely before cleaning.
Never immerse the kettle or cord in water, or allow moisture to
contact with these parts.
Removal of mineral deposits
Mineral deposits in tap water may cause the kettle interior to
discolor .To remove this build-up, use non-toxic Liquid Descaler.
Alternatively:
1. Fill the kettle with 3 cups of white vinegar and the remainder
of water and be allowed to stand overnight. Do not boil.
-8-

2. Empty the solution from the kettle.Any stains remaining
inside the spout can be removed by rubbing with a damp cloth,
fill the kettle with clean water, bring to boil and then discard the
water. Repeat and the kettle will then be ready to use.
Cleaning external housing
Wipe the external housing with a wild and damp cloth or cleaner.
CAUTION: Do not use chemical, steel, wooden or abrasive
cleaners to clean the outside of the kettle.
Cleaning the filter
Remember to clean the filter with a wild and damp cloth at
intervals.
Storage
When not in use or storage, the power cord may be wound
around the cord storage under the base of kettle.
Environment friendly disposal
You can help protect the environment!
Please remember to respect the local regulations:
hand in the non-working electrical equipments
to an appropriate waste disposal center.
-9-

Booth No.3H012, Trading Plaza, No.5, Huanan city,
Pinghu Street, Longgang District, Shenzhen, China
Facebook Page: https//www.facebook.com/aicoks/
Website: www.aicok.cc
Made In China
HOUSEHOLD USE ONLY