AICSYS WMC-704M User manual

WMC-704M
Wallmount-Chassis
User Manual

- 2 -
Copyright Notice
This document and product is copyrighted, January 2014, by AICSYS, Inc. All rights are
reserved. No part of this manual may be reproduced, copied, or translated without prior
notice to AICSYS, Inc.
WMC-704M is trademark of AICSYS, Inc.
Disclaimer:
Specification and information contained in this manual are provided for reference only. We
do not assume any responsibility arising out of the application of the products. This manual
is subject to change without any notice.
January 2014

- 3 -
Table of Contents
Chapter 1 Getting Started ..................................................................... 4
General Information....................................................................................................................4
Product Specification.................................................................................................................4
Packing Checklist .......................................................................................................................4
Recommended Tools .................................................................................................................5
Recommended Working Environment ..................................................................................5
Chassis Mechanical Drawing...................................................................................................5
Chapter 2 Installation Guide ................................................................. 6
Unpacking the Chassis..............................................................................................................6
Removing the top cover and hold-down clamp..................................................................6
Installing the Power Supply Unit.............................................................................................7
Installing the Motherboard .......................................................................................................9
Installing the Expansion Card..................................................................................................9
Appendix A Power Supply Unit ......................................................... 10
Appendix B Motherboard................................................................. 10

- 4 -
Chapter 1 Getting Started
General Information
The WMC-704M Wallmount chassis supports ATX motherboard, and 2 x 5.25” and 1 x 3.5”
external drive bays. The chassis has one 12cm fan, and supports PS2 or mini-redundant
power supply.
Product Specification
Construction
Heavy-duty steel
Drive bay
2 x 5.25" and 1 x 3.5”external drive bays
Cooling fan
1 x 12cm ball-bearing fan
Switch
On/Off switch and reset switch
Indicator
Power On/Off and HDD activity LEDs
Expansion
7 x full-height expansion slots
Dimension (W x D x H)
330 x 406 x 204.2mm; 13 x 16 x 8 inches
Weight
NW: 7.7kg / GW: 9.4kg
Packing Checklist
1 x Wallmount bracket
20 x PSU & Card hold bracket screw
20 x Wallmount bracket screw
8 x Fastener
20 x 3.5" HDD screw
5 x Card hold bracket
20 x 5.25” Drive screw
5 x Fastener adhesive (Small)
20 x Motherboard screw
1 x Fastener adhesive (Big)
20 x Standoff
4 x Rubber foot adhesive

- 5 -
Recommended Tools
- Philips Head Screwdriver
- Flat Head Screwdriver
- Forceps (for pulling out jumpers and screws)
Recommended Working Environment
A flat anti-static work surface is required when assembling a complete system
Chassis Mechanical Drawing
Drawing with dimension in millimeter:

- 6 -
Chapter 2 Installation Guide
Unpacking the Chassis
The WMC-704M is shipped in a plastic bag that is placed inside a cardboard box. The
accessories are also shipped with the chassis. When you unpack the chassis you must:
- Make sure all the accessories and bracket (1 set) listed above are present.
- Make sure the chassis has not been damaged in anyway. The installation steps outlined
above are described in detail below. Please refer to the relevant section(s).
Removing the top cover and hold-down clamp
The top cover is secured by a total of six screws (two on each side and two on rear side of
the chassis).To remove the top cover, please follow the steps below:
1. Remove all five top cover retention
screws
2. Slide the cover toward rear of the
chassis, then lift the cover off the chassis

- 7 -
Installing the Power Supply Unit
Once the top cover have been removed, a user supplied PSU can be installed. The PSU is
installed at the rear of the chassis and secured to the chassis with four retention screws. To
install the PSU, please follow the steps below:
1. Remove the card hold bracket by
removing the two screws
2. Correctly position the PSU at the rear of
the chassis with the power switch and
cable socket both facing outwards.
Secure the PSU by inserting four
retention screws through the rear of the
chassis
Compatible Power Supply Unit models are available in AppendixA.
Installing the Hard Disk Drive
The WMC-704M chassis supports two 5.25”and one 3.5”external drive bays.
To install the drives, please follow the steps outlined in the sections below.
1. Remove the screws (4x screw per one
drive cage) and take the drive cage out

- 8 -
2. Remove the screws (2 screws for one
cover) to remove the drive cage covers.
Secure the Optical drive and/or hard disk
drive to the cage.
3. Carefully insert the ODD drive into the
drive tray, and secure the drive by
inserting four retention screws (four on
each side) through the sides of the drive
tray
4. Carefully insert the 3.5” HDD into the
drive tray, and secure the HDD by
inserting six retention screws (three on
each side)on each side) through the
sides of the drive tray

- 9 -
Installing the Motherboard
To install the ATX motherboard, please follow the instructions below:
1. Insert the standoffs to the predrilled screw
holes in the bottom plate
2. Lay the motherboard to chassis and
secured with screws to the standoff
below
Different motherboard may have different Screw hole positions, please refer to their own
User manual for details.
Compatible motherboard models are available inAppendix B.
Installing the Expansion Card
To install the Expansion Card please follow the instructions below:
1. Remove the slot cover by removing the
screw at top of the slot cover
2. Slide the Expansion card into the socket
on the motherboard reserved for the
Expansion card.
3. Secure the expansion card I/O bracket
with screw

- 10 -
Please make sure to disconnect the Power Supply before installing the Expansion Card.
Do not turn on power during the installation process
Electrostatic Discharge (ESD) can damage electronic components. To prevent damage
to your system, use a grounded wrist strap designed to prevent static discharge
Appendix A Power Supply Unit
Compatible Power Supply Units are listed in the table below:
Model number
Wattage
Type
Dimension (W x D x H)
SS-400ES
400W
Single output
150 x 140 x 86mm
SS-600ES
600W
Single output
150 x 140 x 86mm
SS-400R8P
400W
Redundant PSU
150 x 199 x 86mm
R4S-400G1V2
400W
Redundant PSU
150 x 174 x 86 mm
R4S-500G1V2
500W
Redundant PSU
150 x 174 x 86 mm
R4B-500G1V2
500W
Redundant PSU
150 x 199 x 86mm
Appendix B Motherboard
Compatible AICSYS motherboards are listed in the table below:
Model number
Type
PCI
PCIe
ISA
PSU type
MBC-6508
Mini-ITX
N/A
1
N/A
ATX
MBC-6243
Mini-ITX
N/A
1
N/A
ATX
MBC-6240
Mini-ITX
N/A
1
N/A
ATX
MBC-6230
Mini-ITX
1
N/A
N/A
ATX
MBC-4506
Mini-ITX
N/A
N/A
N/A
ATX
MBC-4503
Mini-ITX
1
N/A
N/A
ATX
MBC-4229
Mini-ITX
1
N/A
N/A
ATX
MBC-6250
microATX
2
2
N/A
ATX
MBC-6603
microATX
2
2
N/A
ATX
MBC-6510
ATX
4
3
N/A
ATX
MBC-6507
ATX
3
4
N/A
ATX
MBC-6506
ATX
4
3
N/A
ATX
MBC-4220
ATX
4
3
1
ATX