Aimpro21 RC132 User manual

Presenter
User’s Manual
RC132/610/611

RF132, Presenter with RF wireless technology
!!! Attention!!!
A. Do not allow minors to use the laser pointer unsupervised.
Laser pointers are not toys.
B. Avoid direct eye exposure.
C. Never shine the laser pointer at anyone. The laser pointer is
designed to illustrate inanimate objects.
D. Do not point the laser pointer at mirror-like surfaces. A
reflected beam can act like a direct beam on the eye.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
1

RF132, Presenter with RF wireless technology
Table of Content
INTRODUCTION ....................................................................3
FEATURES...............................................................................4
PACKAGE CONTENTS..........................................................5
SYSTEM REQUIREMENTS..................................................5
INSTALLATION AND OPERATION....................................6
1. OPEN THE BATTERY COVER AND INSTALL BATTERIES....6
2. INSTALLRECEIVER...........................................................6
3. PRESENTER BUTTON FUNCTION.........................................7
4. INSTALL aimMasterEZ.......................................................8
5. USE aimMasterEZ............................................................ 11
TROUBLE SHOOTING........................................................14
V1.0
2

RF132, Presenter with RF wireless technology
Introduction
Thank you for purchasing Presenter.
Please read this user’s manual carefully before operating the unit,
and keep it for future reference.
The wireless presenter is the ideal wireless remote controller for
large-scale presentations and conference rooms. 2.4GHz of
wireless technology lets you concentrate on your presentation.
The preset RF connection enables true plug-and-play capability;
no driver is required. The presenter features dedicated
PowerPoint®page-up and page-down control keys, a 360-degree
mouse, and a laser pointer. The software, aimMaster EZ allows
you to put marks during the presentation to attract the audiences’
attention. A travel-friendly design that stores the receiver dongle
into presenter also turns off the switch to conserve power.
We make no representation for the errors, omissions or updates
of this document.
3

RF132, Presenter with RF wireless technology
Features
1. 2.4 GHz RF wireless transmission provide up to 20 meters omni-
directional working range.
2. Built-in laser pointer for presentation guidance.
3. Built-in cursor mouse for 360-degree control.
4. Plug and Play. No driver required.
5. Store wireless USB receiver inside presenter.
6. Useful and friendly software, aimMaster EZ, works under Windows
2000/ XP/ Vista OS and allows you to put marks to attract audiences’
attention.
7. Compact design uses hidden dongle as on/off power switch of RF
and laser.
8. Bright laser beam provides easy to see pointer visibility.
9. Compatible with MS, Openoffice, Google Docs
10. TwoAAA batteries provide long and reliable usage.
4

RF132, Presenter with RF wireless technology
Package contents
zPresenter
zUSB type RF Dongle receiver (RF610 – with 4GB USB device ;
RF611 – with microsd card reader)
zaimMaster EZ Software and User’s Manual CD-ROM
zTwo AAA batteries
zQuick Guide
System Requirements
zMicrosoft®Windows®2000/XP/ Vista and Mac OS
z512MB RAM recommended
zCD-ROM drive or DVD-ROM Drive
zUSB Port; PC platform
5

RF132, Presenter with RF wireless technology
Installation and operation
1. Open the battery cover and Install batteries
Open the battery cover of presenter and take off the receiver with 45
degrees angle from the receiver dock before you start to use.
(Please insert the receiver into the receiver dock of the presenter with
45 degrees angle after the presentation. The Power Switch inside the
presenter dock will turn off the power when you put the receiver in)
Put in two AAA batteries and close the battery cover.
Power on/off button
Receiver dock
2. Install Receiver
Plug receiver into the USB port of your computer. Please put your
presenter closed to the receiver around within distance 5 cm and press
any button of the presenter around 3 seconds except laser button, the red
indicator of presenter will keep flash if quick-link is successful. If the
receiver is inserted correctly, the blue indicator of receiver will flash once
6

RF132, Presenter with RF wireless technology
when Presenter key is pressed.
3. Presenter button function Red indicator
PAGE UP LASER
PAGE UP
PAGE DOWN PAGE DOWN
Mouse STICK
LEFT RIGHT
Power on/off button
Receiver dock
7

RF132, Presenter with RF wireless technology
Button Function
or PAGE UP button (suit for left-handed or
right-handed user)
or PAGE DOWN button (suit for left-handed or
right-handed user)
LASER button (if receiver is put into presenter,
the laser power is off and can’t operate)
Mouse LEFT button
Mouse RIGHT button
Mouse STICK (use your finger tip to push
STICK to any direction.)
Power on/ off button (on/off power switch of
presenter)
4. Install aimMaster EZ
Insert the CD to your computer. The following window will pop up.
Click “Next”
8

RF132, Presenter with RF wireless technology
Click “Next”
Click “Install”
9

RF132, Presenter with RF wireless technology
Choose “Yes, I want to launch aimMaster EZ now” and click
“Finish” to start using aimMaster EZ.
Double Click the shortcut icon of
aimMaster EZ exe file shown on
your desktop to activate
aimMaster EZ.
The message window will pop up
3 seconds to remind you that the
aimMaster EZ is activated. You
will see the aimMaster EZ icon
on the system tray. The
system tray icon will be
disappeared when the receiver is
removed.
10

RF132, Presenter with RF wireless technology
5. Use aimMaster EZ
In a presentation, you can use the mark pen to highlight some
important articles or blank the screen to catch the audiences’attention.
aimMaster EZ supports two mark pens, Check Pen and Line Pen. It
also provides a blank function. You can blank the screen so that the
audiences will focus on your speech. When you enter aimMaster EZ,
you can click the RIGHT button to choose one of the 4 modes, Check
Pen, Line Pen, Mouse and Blank.
Check Pen Mode
Press and hold the RIGHT button for
2 seconds to enable aimMaster EZ. The
first mode entered is Check Pen Mode. A
check symbol will replace the cursor
symbol and the aimMaster EZ icon on
the system tray will be changed from
to .
In the Check Pen Mode, each LEFT
click will leave a red check mark
below the cursor position.
Please refer to the following table for the different modes.
Mark Pen Mode Cursor Mark System Tray
Check Pen
Line Pen
Mouse •n.a.
Blank n.a. n.a. n.a.
Note: When you turn on your computer, please remember to run
aimMaster EZ, otherwise when you press and hold RIGHT button for
2 seconds, you can NOT enter the Check Mark Mode.
11

RF132, Presenter with RF wireless technology
Line Pen Mode
Click the RIGHT button once;
aimMaster EZ will go from the Check
Pen Mode into the Line Pen Mode.
The cursor symbol becomes and
the aimMaster EZ icon on the system
tray is changed from into .
In the Line Pen Mode, press and hold
the LEFT button will draw a red
line from right end of the cursor
location and this red line extends
towards the right direction. The
longer you hold the LEFT button
, the longer the red line is.
Mouse Mode
Click the RIGHT button again to
go from the Check Mode into the
Mouse Mode. In this mode, the cursor
becomes an arrow . The aimMaster
EZ icon will change to on the
system tray. It has the normal mouse
functions. You can move the Mouse STICK and LEFT/RIGHT click
your hyper-link file that is inserted in your Presentation file.
In the Mouse Mode, click the RIGHT button to go back to the
Check Pen Mode. In this way, the 3 modes, Check Pen, Line Pen, and
Mouse, are cycled by the RIGHT button clicks.
Undo the Marks
To undo the Check/Line Marks you have done on the screen, click
PAGE UP button once will clear the latest Check/Line Mark. The
further PAGE UP clicks will undo the marks until all the Check/Line
marks are cleared.
12

RF132, Presenter with RF wireless technology
Clear all Marks
To clear all Check/Line Marks, you may either click PAGE DOWN
button once, or, press the ESC key of your keyboard. aimMaster EZ is
then disabled.
When you want to use mark pen again, press and hold RIGHT button
for 2 seconds to enable aimMaster EZ and enter the Mark Pen
Mode as we described previously.
Blank the Screen
When aimMaster EZ is enabled, press and hold the RIGHT button
for 1 second, the screen becomes blank. To get back the original
screen, click PAGE DOWN button once. aimMaster EZ will go back
to one of the 3 modes, Check Mark, Line Mark, and Mouse.
Quit from aimMaster EZ
If your receiver is unplugged
from the computer, the icon on
the system tray will be hidden,
but aimMaster EZ is still
running. Please move the cursor
above the aimMaster EZ ic
the system tray, click the RIGH
button
on on
T
and then, LEFT click
“quit” to exit from aimMaster EZ.
13

RF132, Presenter with RF wireless technology
TROUBLE SHOOTING
1. How to re-link Presenter and Receiver
If you cannot do the previous steps successfully or need to clear previous
pairing setting, you need to re-link the presenter with receiver. Keep
pressing both UP and DOWN buttons of the presenter at the same time
around 3~5 seconds and LED of the presenter will be keep light. Then the
LED of the presenter will quick flash around 2 seconds, the clean pairing
setting steps will be done. Please put your presenter closed to the receiver
around within distance 5 cm and press any button of the presenter around
1~3 seconds except laser button, the red indicator of presenter will keep
flash if quick-link is successful. If the receiver is inserted correctly, the
blue indicator of receiver will flash once when Presenter key is pressed.
Then you can start to use the presenter.
After the successful pairing, the LED of presenter and receiver will flash
once
when press the button.
2. If you miss the Receiver
After you buy a new receiver, you need to clear previous pairing setting.
Please keep pressing both UP and DOWN buttons of the presenter at the
same time around 3~5 seconds and LED of the presenter will be keep
light. Then the LED of the presenter will quick flash around 2 seconds,
the clean pairing setting steps will be done.
Please put your presenter closed to the receiver around within distance 5
cm and press any button of the presenter around 1~3 seconds except laser
button, the red indicator of presenter will keep flash if quick-link is
successful. If the receiver is inserted correctly, the blue indicator of
receiver will flash once when Presenter key is pressed. Then you can start
to use the presenter.
After the successful pairing, the LED of presenter and receiver will flash
once when press the button.
3. It’s not work when you press the button.
If the button cannot work when you press, and laser is still working,
please change your battery and try again.
4. If you feel your cursor is moving too fast or slow when you use the
mouse stick of the presenter
Please go to the control panel of your PC system to adjust the mouse
speed.
5. If your cursor can’t change to the and mark when you move to the
14

RF132, Presenter with RF wireless technology
15
some page
When you under the present mode of or , if the cursor can’t appear the
mark that you choose during operate under some software,you can recognize
your current cursor mode from the icon on task bar like below.
6. LED conditions:
After the successful pairing,if receiver is not plug or not get the singal
from presenter, the LED of presenter will be on for half second if press
the buttons (except laser button) ,and the LED of presenter will be off
after 3 seconds if keep pressing the buttons (except laser button).
If before pairing condition, the LED of presenter will be on for 1 second
if press the buttons 0.5 second (except laser button), the LED of RC will
be on for 1 second, and the LED of the presenter will be off after 5
seconds if keep pressing button (except laser button),