Aiphone IP-EWST User manual

- INSTRUCTIONS -
The IP-EWST offers voice-quality Intercom function over TCP/IP based networks. Designed specifically to
integrate seamlessly into a new or existing LAN / WAN infrastructure, the IP-EWST is capable of hundreds of
stations, fulfilling a large variety of applications including commercial, industrial and residential access
control; general security, office, and institutional intercom / paging; and many more. Power over Ethernet
(PoE) capability is also supported (IP-EWST-POE only), allowing greater installation flexibility for both new
and retrofit applications.
Intercom-Over-IP Adaptor Set
Pg. 1
NAMES & FEATURES
FEATURES:
Cost-effective PC-based design
Compatible with IF-DA / IE-JA and LE-series
substations, as well as standard speaker /
pushbutton stations
Scalable to hundreds of stations / locations
Works with standard wired and wireless TCP/
IP networks (LAN/WAN)
Digital audio recording and playback capability
Relay output for remote release (N/O and N/C)
NAMES & FUNCTIONS:
1. RJ-45 10/100 Ethernet jack &
connection indicator LEDs
2. 2.1mm Power jack
3. 3.5mm Audio output jack
4. 3.5mm Mic input jack
5. Sub station personality jumper
6. Sub station / relay terminals
7. Manual sub station push buttons &
Diagnostic LEDs (LD1,LD8,LD9,LD10)
9. Wire access hole
IP-EWST
IP-EWST-POE
0409
1
2
3
5
6
7
94
2W ST
Package Contents:
(1) IP-EWST or IP-EWST-POE
(1) Talkmaster™LE mini-CD
(4) Chassis screws
(2) Adhesive-backed pull tie guides
RESET + - TALK
LD10
LD9 LD8 LD1

INSTALLATION & MOUNTING
Installation Instructions:
1. If IP-EWST adaptor is not on the same LAN
or network segment as the PC master
station, ensure that the IP-EWST has been
pre-programmed with the proper TCP/IP
connection settings prior to physical adaptor
installation. See TalkMaster™ installation
manual (included on CD with IP-EWST).
2. Set the personality jumper based upon your
chosen sub station. IE-JA and IF-DA subs
will work in “2W” mode. Any standard LE-
series sub (remove E/- jumper) or 4Ω~ 20Ω
speaker will work in “ST” mode.
3. Wire the sub station to the proper screw
terminals on the IP-EWST, and connect to
the network using the standard RJ-45 jack.
Wiring from the sub station to the IP-EWST
should be jacketed multi-conductor with
overall shield. Connect the included power
supply to 2.1mm power jack (unless using IP-
EWST-POE)
2W ST
2W ST
Personality
Switch Settings
IE-JA/IF-DA
Sub stations
2W ST
LE-Series
Sub stations
Mounting Instructions:
1. Ensure that proper sub station and network connections have been
made prior to closing the IP-EWST chassis.
NOTE: Once unit is mounted, the chassis cannot be opened to
modify sub station wiring and internal settings.
2. Mount the IP-EWST adaptor in a controlled area or in an enclosure
suitable to the installation environment. The stock IP-EWST chassis
is not vandal resistant or weather resistant. Mounting holes are
located on the top center and bottom center of the back chassis.
Mounting hole
Mounting hole
Pg. 2
IE-JA / IFDA Sub stations
2-Conductor connection to
IE-JA / IF-DA sub stations
Relay Output
for Door/Gate
N/C
Com
N/O
LE-Series Sub station or Speaker
3-Conductor connection to
LE-series sub station
Relay Output
for Door/Gate
N/C
Com
N/O
E
1
-
Standard
Speaker*
N/O push button
* When using a standard speaker, connect to E and 1 termination points.
Wiring should be jacketed 3-conductor.
Wire distance from IP-EWST to LE series sub:
22AWG = 650 feet, 18AWG = 1600 feet
*
* Wiring to sub station should be jacketed 2-conductor.
Wire distance from IP-EWST to IE/IF sub:
22AWG = 500 feet, 18AWG = 1180 feet

SOFTWARE INSTALLATION
1. Insert the mini-CD (included with the IP-EWST / IP-EWST-POE set) into the PC to be used as a
master station.
2. Install the TalkMaster™ software by following the on-screen prompts, or by navigating to your CD
drive and executing “setup.exe” to begin the installation process.
3. Consult the TalkMaster™ User Guide document for further software functionality and configuration
information.
Pg. 3
HARDWARE DIAGNOSTICS & TROUBLESHOOTING
To confirm proper hardware functionality, it is best to use an Ethernet crossover cable (not included).
This can be used to directly connect the IP-EWST to any PC with a standard 10/100 Ethernet interface
for troubleshooting and preprogramming.
Follow these steps to troubleshoot proper connection:
1. Ensure proper power is connected to the IP-EWST. If using the IP-EWST-POE, make sure that
the Ethernet device being connected is 802.3af-compliant, or that a proper power supply is used
(7.5 to 9VDC, 500mA). Do not connect both Power-over-Ethernet and a separate power supply!
2. Check the IP-EWST diagnostic LEDs labeled LD10, LD9, LD8, and LD1 for proper illumination
(located next to the manual substation pushbuttons). Consult the following table for LED indicator
status meanings:
Operational Mode LD10 LD9 LD8 LD1
Normal operational mode. TalkMaster™ is
active. Intercom can communicate. ON ON - -
- -
LAN connection is inactive. The RJ-45 may
be unplugged, or LAN lost power. FLASH OFF
DHCP IP is enabled but address is not
being assigned. FLASH ON -ON
TalkMaster™ software is not running on
PC or not set to communicate. FLASH ON - -
TalkMaster™ software at the server has
"Scanned" for intercoms in the
Configuration Mode utility setup.
FAST FLASH ON - -
Receiving audio. The TalkMaster™
software / PC microphone is on. ON -FLASHON
Sending audio. Manual talk button is
pressed or TalkMaster™ has engaged
"listen" mode.
ON -ONON
Intercom is in "Server" mode, waiting for a
client to request connection (LD10 flash
alternates 1sec fast, 1sec slow).
DUAL FLASH - --

SPECIFICATIONS
Hardware Specifications:
Input Voltage: IP-EWST – 7.5-9VDC, 500mA, use included power supply
IP-EWST-POE – IEEE 802.3af compliant
Network Interface: 10/100 Base-T Ethernet (Auto detection) RJ-45
IP Assignment: Static or Dynamic via DHCP
Hardware Protocols: TCP, UDP, IP, ARP, ICMP, Ethernet MAC
Transport Bandwidth: ≈80kbps per TCP/IP session
LED Indicators: Active, Link, Talk, Reserved
Audio Resolution: PCM-8 and uLAW-16 bit
Audio Sample Rate: 8kHz
Audio Buffers: 4kb transmit and receive
Audio Latency: Target delay < .5 sec. Typical delay ≈.3 sec.
Output Amplification: Maximum 2W @ 4Ω. Actual determined by sub
Relay Contact Rating: 30VDC / 1A (resistive)
Operating
temperature: 32°F to 158°F (0°C to 70°C)
Dimensions: 6-3/4″H x 4-1/8″W x 1-3/4″D
Software System Requirements:
For optimum performance, TalkMaster™ requires a minimum of the following:
Operating System: Microsoft Windows® 98SE, Windows ME, Windows NT® (SP6),
Windows 2000, or Windows XP
Processor: 750MHz or faster
Memory: 128MB of RAM (256MB recommended)
Hard drive: 50MB of available disk space
Sound Card: Windows supported sound card (with speaker and microphone)
Aiphone Communication Systems
1700 130th Ave. N.E.
Bellevue, WA 98005
[phone]
FAX [phone]
Pg. 4
IP-EWST Instr
0409TBJS
WARRANTY
Aiphone warrants its products to be free from defects in material and workmanship under normal use and
service for a period of one year after delivery to the ultimate user. We will repair free of charge or replace at no charge
Aiphone product, that upon examination by an Aiphone Repair Technician is proven defective and under warranty.
Aiphone reserves the right to make the final decision whether there is a defect in materials and/or workmanship; and
whether or not the product is within the warranty.
This warranty covers bench repairs by the Aiphone Service Department only, and does not extend to units that
have been repaired or altered outside of the factory. Aiphone is not responsible for any costs incurred involving on-site
service calls.
This warranty shall not apply to any Aiphone product that has been subjected to misuse, neglect, accident,
power surge, or used in violation of instructions furnished.
4 1/8″
2 1/16″
6 3/4″6″
TalkMaster™ and ii3™ are trademarks of Digital Acoustics Corporation, 263 Market Square, Lake Forest, IL 60045.
Digital Acoustics® is a registered trademark. Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation
in the United States, and/or other countries.
TOLL FREE TECHNICAL SUPPORT:
[phone]
E-MAIL: [email protected]