Aiphone AN-8500MS User manual

IN
Thank you for purchasingAIPHONE's IP MultifunctionalMasterStation.
Pleasecarefullyfollow the instructionsin
this manual to ensure long,trouble-freeuse of your equipment.
0 Before installation or use, be sure to carefully read
all the instructions in this section for correct and
safe operation.
0 Be sure to follow all the precautionary instructions
in this section, which contain important warnings
and/or cautions regarding safety.
0 After reading, keep this manual handy for future
reference.
Indicates a potentially hazardous situation which,
if mishandled, could result in moderate or minor
personal injury,and/or property damage.
When the Unit is in Use
0 Use the dedicated AC adapter or its equivalent for
the unit. Note that the use of other adapter may
cause a fire.

5. WALL MOUNTING
The optional YC-280 Wall mountingbracketis required.
The
YC-280 can be mounted to a one-gang electrical box.
5.1. Mounting
Step 1. Installthe YC-280 to the wall
Notes
0 Usethe appropriatescrews for the construction
0 Wood screws 3.5 x 20 are supplied with the
0 No fitting screws for an electrical box are
of wall.
YC-280.
supplied.
Usecommerciallyavailablescrews.
Step 2.
Hang the station on the wall mounting bracket
hook
to install.
Push down the station body in the direction
indicatedby the arrows.
5.2. Installation Completion Drawing
Unit: mm
148
YC-280
Wood screw 3.5 x 20
(supplied with the YC-280)
5.3. YC-280 Dimensional Drawing
4.6 x 6
Unit:
iting
mm
K- IN
In desktop installations, the front operation panel can be inclined 16" from the desk surface for easier operation by
attachingthe
YC-280 Wall mountingbracket to its bottomsurface.
6.1. Mounting
Hangthe YC-280's hook on the station'swall bracket mounting slot
to install.
Pushup the
YC-280 inthe directionindicatedby the arrows.
YC-280 Wall
AN-8500MsA h mountingbracket
~~
Rubber foot
6.2. Installation
Unit: mm
t-
205.2
YC-280
Hook the YC-280)

7. WIRING
* Applicable cables are as follows.
COM HOT
Conductor diameter:
00.4
- 1.3mm (AWGI6 - 26), Solid wire
00.7
- 1.4 mm (AWGI6 - 22), Stranded wire
0 When using the external speaker, IN-,-. EXT.
set the internal/external speaker sp sp
switch on the bottom to the EXT.
SP position.
I
Power supply connection
The following 2 methods are available for
supplying power
to the station.
0 From a DC 12 V AC adapter
0 From an IEEE802.3af compliant PoE
AN-8500MS rear
switching hub
Can be connected to a network of IOBASE-
TI1OOBASE-TX in auto-sensing.
Use a UTP category
5 straight-through cable
with an RJ-45 connector for this connection.
12V- 4WmA
(For connection, refer to the instruction
manualsupplied with the switching hub.)
AC adapter connection
Cable <>-T-T>
Connect the AC adapter*.
Installthe supplied
ferrite
clamp on the AC adapter
cable
by winding the
cable around the ferrite
clamp once
Ferriteclamp (accessory)
* Use the AC adapter AD-121 OP (optional)or the equivalent.
b
As for the usable adapter, consult the AIPHONE sales
Off
PC connection
Use a UTP category 5 straight-
through cable with an RJ-45
connector for this connection.
External speaker connection
Press down the desired push-
interminal buttonwith a tip of
standard driver, and insert
the cable securely. 11 mm
8. A SQRY
CD* .................................................................... 1 AC adapter: AD-1210P
Ferriteclamp
...................................................... 1 Wall mountingbracket: YC-280
*
Contains the AN-8000 setting software program and
the AN-8000 series instruction manual. The Setup
Launcher is automatically started when the supplied
CD-ROM is inserted into the PC'sdrive.
Note
If your PC's CD drive is not compatible with the
AutoRun function, the setup guide is not automatically
started even when the CD is inserted. Use either
"Explorer" or "My Computer" to execute the following
files, or use [Start
-+ Run] in the Task Bar and enter
the following command.
<Drive where CD is placed>\index.html
For example, when placingthe CD inthe "d"drive,
4 d:\index.html
(- Version update information
0 Pleasecontact to the AIPHONE sales office to obtain
the up-to-date version for firmware, software and the
instructionmanuals.
0 The software version number can be confirmed using
the Help menu.
0 The current firmware version can be confirmed on the
system management screen displayed when the
browser establishes the connection
to the station.
0 The instruction manual version number can be
confirmed by checking the preparation date (year and
month) shown at the lower right corner of the last
page.
Example:Prepared in July 2006: 200607