Aiphone Ja-2hcd User manual

JA-2MECD
Master monitor station(with Picture memory)
JA-2MCD
INSTALLATION & OPERATION MANUAL
HANDSFREE COLOR VIDEO INTERCOM
834571 1004 B
JA-2MECD JA-2HCD
JA-2MCD
Master monitor station
JA-2HCD
Sub monitor station

- 2 -
General Prohibitions
General Precautions
Prohibitions to dismantle the unit
Prohibitions to subject the unit to water
WARNING
(Negligence could result in death or serious injury to people)
1. High voltage is present internally. Do not open the case. Electric
shock could result.
2. Do not dismantle or alter the unit. Fire or electric shock could
result.
3. Do not connect the unit with any non-specified power source. Fire
or electric shock could result.
4. Keep the unit away from water or any other liquid. Fire or electric
shock could result.
5. Do not put any metal into the unit through the openings. Fire,
electric shock, or unit trouble could result.
6. When existing chime wires are used, it is possible that they contain
AC voltage. Electric shock or unit damage could result. Ask a
qualified technician.
CAUTION
(Negligence could result in injury to people or damage to property)
1. Do not put anything on or cover the unit with cloth, etc. Fire or
unit trouble could result.
2. In case of electrical storms, unplug the unit from AC outlet. If not,
fire or electric shock could result. (If AC cord is not seen, turn off
the Power switch on the left side.)
3. If LCD is punctured, do not allow contact with the liquid crystal
inside. Inflammation could result. If necessary, gargle your mouth
and clean your eyes or skin with clear water for at least 15
minutes, and consult your doctor.
4. Do not install the unit in any of the following locations.Fire,
electric shock,or unit trouble could result.
* Places under direct sunlight, or near heating equipment that
varies in temperature.
* Places subject to dust, oil, chemicals,
* Places subject to moisture and humidity extremes, such as
bathroom,cellar, greenhouse, etc.
* Places where the temperature is quite low, such as inside a
refrigerated areaor in front of air-conditioner.
* Where noise generating devices such as dimmer switches,
invertor electrical products.
* Places subject to steam or smoke (near heating or cooking
surfaces).
* Where noise generating devices such as dimmer switches,
invertor electrical appliances, are closeby.
* Places subject to steam or smoke (near heating or cooking
surfaces).
GENERAL PRECAUTIONS
1. The unit is for domestic use only. Do not use outdoors.
2. When power fails, the unit becomes inoperative.
3. The unit is for wall-mount use only. For desktop applications, use
desk stand.
4. In areas where broadcasting station antennas are close by, the
intercom system may be affected by radio frequency interference.
5. If the phone is operated near OA equipment, Radio or TV, they
interactively influence by radio frequency interference. Carefully
select both locations for installation and operation.
PRECAUTIONS
Package contents
1 JA-2MECD, JA-2MCD or JA-2HCD
2 Packet of screws
3 Optional function connector
4 Door release connector
5 Mounting bracket
6 INSTALLAITON & OPERATION MANUAL
1PACKAGE CONTENTS
2INSTALLATION
2-1
Installation locations
1. Do not mount the inside monitor station in areas directly facing bright
lighting. Viewing image may be affected.
2. On the left side, the monitor station has a POWER switch. Secure a
space of 50mm(2") or more between the unit and a wall or furniture.
1
JA-2MECD
2
3
4
5
6
JA-2HCD
JA-2MCD
50mm+
(2")
[1]
[2]

- 3 -
2-2
Wiring method
Wire the inside stations in a station-to-station (daisy-chained) manner.
3MOUNTING
2-3
Cable
1. Use 2-conductor, non-shielded cable. Vinyl-jacketed cable with
PE(polyethylene) insulated wires is recommended.
2. Never use loose wires, shielded wire, twisted pairs, or coaxial cable.
3. When using existing cable with multiple wires, terminate both ends of
each unused pair with a 120 ohm resistor.
2-4
Wiring distance
1.0mm
100m
100m
100m
10m
100m
A
A'
B
C
D
18AWG
330'
330'
330'
33'
330'
0.65mm
50m
50m
50m
5m
50m
22AWG
165'
165'
165'
16'
245'
100m
E330'50m 165'
Mounting
[1] Screw (x4)
[2] Mounting bracket
[3] Two-gang box
• Provide a box DEEP enough to accommodate all cables incl. options.
[4] DIN rail
1. Depress UNLOCK button (to unlock or to insert the wire securely).
2. Insert the cable into terminal.
3. When GANG BOX is not provided, the cable can be surface run from
the top or bottom of the unit. Cut open the cable inlet hole to run
wires to the back of the unit.
JA-2MECD
JA-2MCD
JA-2MECD
JA-2MCD
JA-2MECD
JA-2MCD
JA-2SD
JA-DAC
2
2
44
B1, B2
B1, B2
B1, B2 B1, B2
4
4
JA-DAC
JA-DAC
2
B1, B2
JA-2HCD
JA-2SD
JA-2HCD
JA-2SD
JA-2HCD
JA-2SD
JA-2HCD
8
4
4
JA-DAC
2
B1, B2
JA-2SD
JA-2HCD
JA-2SD
JA-2HCD
JA-DAC
JA-D
JA-2HCD
B1
B2
A1
A2
B1
B2
+
-
+
-
B1
B2
A1
A2
(x2)
A1
A2
A1
A2
120 120
JA-2MECD
JA-2MCD
JA-2MECD
JA-2MCD
JA-2HCD
JA-2HCD
PS
JA-DAC
JA-DAC
JA-D
PS-2420
PS-2410
D1 D2
M
S1
S2
AA'
B
C
E
D
IER-2
JA-2SD
JA-2SD
ADAP
CAM
JAW-AZ
: motion detect sensor or sensor / camera
CAM
JA-2MECD
JA-2MCD
JA-2HCD
PS-2420
PS-2420S
PS-2420UL
PS-2420DIN
PS-2410DIN
83.5mm
(3-5/16")
46mm
(1-13/16")
[3]
[2]
[1]
[4]
83.5mm
(3-5/16")
[3]
[2]
12
9mm
(3/8")
3.

- 4 -
4WIRING
A
B1
B2
B1
B2
[5]
[6]
PS-2420
4
PS-2420DIN
[8]
[9]
[8]
[2]
[2]
[2]
+ -
100V-240V~
50/60Hz
230V AC
N
L
24V DC2A
24V DC
2A
IN 230V~ 50/60Hz NL
2A
- +
-
PS-2410DIN 230V AC
N
L
24V DC1A
IN 230V~ 50/60Hz NL
1A
- +
-
OP
EL-9S
EL-9S
A1 A2
[3]
JA-DJA-DAC
2
DC 24V
Motion detect
Camera
Motion detect
Camera
P
2
2
2
2
2
2
NP
NP
NP
NP
NP
NP
AIPHONE
MK-DVF
A1 A2
[4]
AIPHONE
MK-DVF
JA-2MECD JA-2HCD
JA-2SD
ON
JA-2MECD JA-2HCD JA-2HCD
JA-2SD JA-2SD
OFF ON
SUB IN
SUB OUT
JA-2HCD JA-2SD
JA-2SD
IER-2
[7]
SUB IN
SUB OUT
ON - OFF
ON - OFF
JA-DAC
-
A
B1
B2
B1
B2
[8]
[2]
JA-2HCD
-
L1
C1
L2
C2
L1
L2
[10]
RY-3DL JA-2MECD
+
+
-
DC24V
b1
b2
b3
D1
D2
E
PS24
YE(b2)
OG(b1)
L
#1
#2
OG: Orange
YE: Yellow
BR: Brown
RD: Red
PT
4
A1
A2
A1
A2
C1
C2
C1
C2
S
S
B1
B2
[1]
JA-2MECD
JA-2MCD
[8]
-
PT
2
NP
PT
Adaptor
Adaptor
1
E
JAW-AZ
JAW-AZ
-
+
+
DC24V
+ -
++ -
-
SUBMASTER
DOOR-1
DOOR-2
ADAPTER-1
ADAPTER-2
CALL EXT
SPEAKER
+ -
OP
OP
RD(L1)
BR(L1)
YE(L2)
OG(L2)
OPTION
L1
L1
L2
L2

- 5 -
Wiring
Insert the wire into the terminal securely.
[1] Master monitor station JA-2MECD, JA-2MCD
[2] Sub monitor station JA-2HCD or Sub master station JA-2SD
(Audio only)
[3] Video door station JA-DAC
[4] Video or audio door station JA-DAC, JA-D
[5] Power supply +, –(DC 24V)
[6] OPTION Door release EL-9S (12V AC 0.35A) or equivalent
Requires a separate AC transformer. Separately run a cable
for each audio/video and door release.
[7] OPTION Call extension speaker IER-2
[8] Impedance matching switch
Terminate the last sub station, putting SW to A position.
Otherwise both video image and audio quality will be
affected.
[9] Adaptor for Motion Detect Sensor & Camera (SOP available
in USA only)
[10] OPTION Use RY-3DL adaptor to connect 1~2 door releases
of other manufacture, rated more than EL-9S.
NP: Non-polarized P: Polarized
4-1
4-2
Options
1 Foot talk switch
Connect foot call switch (locally available) to PURPLE, BLUE
wires (dry contact closure).
2 Manual press-to-talk restriction
Short between PURPLE and GREEN wires to prevent manual
TALK button operation.
3 Local door release
Connects a local door release which has bigger contact
capacity than EL-9S. For two door releases, use an RY-3DL
adaptor (See Wiring diagram of RY-3DL on Page 4).
4 Video output to video apparatus, video printer, etc. (NTSC,
1Vp-p/75 Ω).
5 Two EL-9S door releases
Connect an EL-9S to BROWN & RED leads, which
corresponds to Door station 1. And, for door station 2, connect
the other EL-9S to ORANGE & YELLOW wires.
•For JA-2HCD, only the functions No.1 & 2 are available.
•Cut off unused wires to prevent shorting.
5NAMES
5-1
Names (JA-2MECD)
[1] LCD (4 inch color)
[2] POWER Switch
[3] Speaker for chime & internal pre-tone/voice
[4] ABSENCE SET button
[5] PLAY button
[6] REC button
[7] Mic.
[8] Door call-in LED (red)
[9] PanTilt control pad
[10] MONITOR button
[11] Screen brightness control
[12] ROOM CALL button
[13] Transmit LED (red)
[14] Door release button
[15] TALK button
[16] VIDEO output (JA-2MECD only)
[17] Camera white light auto ON/OFF switch
[18] Active door call-in selector switch 1, 2 & 1&2
[19] Chime TONE volume control
L1
L1
L2
L2
#2
#1
E
+
b2
b1
V
-
V +
[2]
(BR)
(RD)
(OG)
(YE)
[5]
(RD)
(BR)
(OG)
(YE)
(GR)
(BL)
(PR)
[4]
[3]
[1]
#2
#1
JA-2MECD
JA-2MCD
JA-2HCD
#1
A1
A2
A1
A2
C1
C2
C1
C2
S
S
B1
B2
DC24V
EL-9S
1
EL-9S
2
JA-2MECD
[7]
[1]
[8]
[9]
[10]
[3]
[4]
[5]
[6]
[2]
[11]
[12]
[13]
[14]
[15]
[19]
[18]
[16]
[17]
DOOR
MONITOR
BRIGHT
CALL
SET
PLAY
REC
1
2
TALK
LH
SET SAVE
VIDEO OUT DOOR
1 2
LIGHT
OFF AUTO CALL
1&2
TONE
JA-2MECD

- 6 -
Names (JA-2MCD / JA-2HCD)
[1] LCD (4 inch color)
[2] POWER Switch
[3] Speaker for chime & internal pre-tone/voice
[4] Motion detect camera SET button (JA-2MCD only)
[5] Mic.
[6] Door call-in LED (red)
[7] PanTilt control pad
[8] MONITOR button
[9] Screen brightness control
[10] ROOM CALL button
[11] Transmit LED (red)
[12] DOOR RELEASE button
[13] TALK button
[14] VIDEO output (JA-2MCD only)
[15] Camera white light auto ON/OFF switch (JA-2MCD only)
[16] Active door call-in selector switch
[17] Chime TONE volume control
5-2 6
INITIAL PICTURE MEMORY SETTING
JA-2MCD/JA-2HCD
[5]
[1]
[6]
[7]
[8]
[3]
[4]
[9]
[10]
[11]
[12]
[13]
[17]
[16]
[14]
[15]
DOOR
MONITOR
BRIGHT
CALL
SET
1
2
[2]
REC
REC
2 Sec. +
SET
SET
SET
PLAY
PLAY
PLAY
REC
1/JAN/04 0:00
1/JAN/04 0:00
1/JAN/04 0:00
1/JAN/04 0:00
1/JAN/04 0:00
[1]
[2]
SET
16 (4-frame in one picture)
REC
SET
PLAY
[3]
[4]
[5]
16 (4-FRAME IN
ONE PICTURE)
16
32
60
Day Month Year Time min
REC
PLAY
1/ JAN/ 04 0:00
1
2
12/OCT/03 15:30
12/OCT/03 15:30
12/OCT/03 15:30
12/OCT/03 15:30
10/OCT/03 20:25
10/OCT/03 09:48
09/OCT/03 20:03
1
5
2
3
4
VIDEO OUT DOOR
1 2
LIGHT
OFF AUTO CALL
1&2 TONE
TALK
LH
JA-2MCD

- 7 -
Answering a door call (AUTO mode)
The station is initially set to AUTO voice switch activation.
1. Momentarily press CALL button.
2. Chime tone sounds, and the monitor turns on with caller’s
image. Door call-in LED 1 or 2 is lit.
3. Press TALK button momentarily and reply handsfree.
4. When finished, press TALK button once to turn off.
Timer; Call-in, 30 sec. Communication, 1 min. (approx.). Press
TALK button to turm back on (if within 30 sec.)
7-4
Instant voice calling for family use
1. Momentarily press CALL button.
2. When chime sounds, the monitor turns on with the image of
the caller. Sound from the entry area is heard through the
speaker of the inside station(s).
Note: Not available on JA-D door station.
7-2
7-3
Monitor a door station
1. Momentarily press MONITOR button.
2. Video monitor turns on image of DOOR 1.
3. Press MONITOR button again to switch to DOOR 2.
4. Press MONITOR button to end monitoring.
Notes:
•Inside audio cannot be heard at door station.
•Press TALK button to establish communication with door
station.
•The image automatically turns off in approx. 30 sec.
•When DOOR2 is audio-only type (JA-D), it is skipped while
monitoring and audio door cannot be monitored.
Pan and tilt the door station camera
The monitor station is equipped with Aiphone's exclusive Pan-
and-Tilt control pad. When the video door station is on, press on
each edge of pad to move the camera up down and right left.
7-1
7OPERATIONS
Initial picture memory setting
Before use, be sure to program in the following manner:
1. Place the unit in SET mode. Press SET button and hold down
for more than 2 seconds. Both PLAY & REC buttons start
flashing.
2. Choose on-screen DATE location. As desired, move up with
PLAY button, and move down with REC button. Press SET
button to select. Next, “2003”flashes.
3. Set time in the order of; (1) Year, (2) Month, (3) Day, (4) Hour,
and (5) Minute. 1/JAN/04 0:00
4. Choose PICTURE MEMORY mode. Move cursor to the mode
desired. (Most recommended is 16 picture, 4-frame). Press SET
button to select.
5. When finished, press TALK button, or programming will
terminate in approx. 2-1/2 minutes. All the buttons are no
longer lit to indicate unit is in standby mode.
Notes:
•When changing PICTURE MEMORY mode, all the previously
saved pictures will be erased. Never change if the saved pictures
MUST be kept.
•It is not possible to go back and partially reprogram DATE
location or TIME. Go back to initial SET mode.
•If setting has ended incompletely within approx. 2-1/2 minutes,
go back to initial SET mode.
[2][1]
[4]
[3]
DOOR
1
2
JA-DAC 2
JA-DAC 1
[1] [2]
[3] [4]
MONITOR
MONITOR
MONITOR
[1] [2]

- 8 -
Transfer a door call
1. While viewing the visitor, press ROOM CALL button. After
pre-tone, call a person desired by voice.
2. At the called stations, after pre-tone, image and audio of door
will be activated.
3. At a responding station press TALK button to reply. When
finished, press TALK at either station.
4. Second person presses TALK once to connect to the door
station. Communicate with visitor. To return to standby, press
TALK button.
7-8
Activating door release
1. Press and hold down DOOR RELEASE button.
2. The door release mechanism will be activated while the button
is pressed.
7-6
Room-to-room communication
1. Press CALL button once. Call by voice to the other inside
station(s).
2. The called station(s) sounds a pre-tone and voice.
3. Press TALK button once, and reply handsfree.
4. When finished, press TALK button once to turn off.
Note: Communication is approx. 1 minute.
7-7
Answering a door call (MANUAL Press to Talk mode)
1. Momentarily press CALL button.
2. Chime tone sounds, and the visitor’s voice is heard. The
monitor turns on with caller’s image. Door call-in LED 1 or 2
is lit.
3. Depress and hold down TALK button for 1 second or more.
4. To transmit, talk while pressing TALK button, and release
TALK button to listen.
5. When finished, press TALK button once to turn off.
Timer; Call-in, 30 sec. Communication, 1 min. (approx.). Press
TALK button to turm back on (if within 30 sec.)
7-5
[1] [2]
[3] [4]
CALL
[1] [2]
[4]
[1]
CALL
[2]
[3]
[2][1]
[5][4][3]
DOOR
1
2

- 9 -
Save in memory
1 (During replay) Press SET button. The image on the screen is
stored in memory. On the screen, M5 indicates the 5th image
(Max. 8 per system).
Note:The image stored in memory will not be overwritten
during another operation. To erase, proceed to ERASE
operation.
2 To release (During replay) While the image is on the screen,
press SET button. The “M”goes out, and memory is cleared.
Note:The image in memory will not be erased, but overwritten
(erased) when new picture is saved.
3 The “on-screen”FULL indicates it is the 9th picture whose
memory is void.
Note:When one frame picture is memorized, all four frame
pictures are memorized as one picture.
8-4
8-3
Replay
1. Press PLAY button. The latest picture is displayed.
2. Press PLAY button repeatedly to view each previous picture
that has been saved. The screen with means the last page.
Press REC button to view retroactively.
3. In replay of 16 (4 frame) pictures, press REC button to view
each frame picture in full screen.
4. To end, press TALK button once, or it will automatically turn
off in approx. 1 minute.
8-2
Manual picture memory
1. Press Monitor button to display the image on the monitor.
2. Press REC button. The REC button is lit to indicate the image
is being saved.
Notes:
•When door calls in, an auto-saved image will be overwritten if
saved manually.
•Manually picture memory is a full-screen image regardless of
the initial program mode.
Automatic picture memory
When video door station calls in, picture memory is automatically
activated (JA-2MECD only). REC button is steadily lit to indicate.
Put JA-2MECD in Surveillance-SET mode to receive image from
Motion-detection camera.
Notes:
•Automatic picture memory is a built-in feature, and cannot be
turned off.
•Auto picture memory is not effective;
- During video monitoring.
- For approx. 4 sec. after ending replay.
- For approx. 15 sec. after the previous save.
8-1
8PICTURE MEMORY
SET
[1] [2]
[3]
M5
2001SEP1 15:30
M5
12 / OCT / 03 15:30
M5
12 / OCT / 03 15:30
SET
SET
12/OCT/03 16:40
[1] [2]
[2]
[3]
[4]
2001SEP1 15:30
PLAY
TALK
REC
PLAY
PLAY
REC
1sec 5sec
9sec 13sec
1 / JAN / 01 15:30
1
1
2
2
3
3
4
4
REC
[1] [2]
MONITOR
JA-2MECD
REC
1 sec
16-picture, 4-frame
5 sec
9 sec 13 sec
1 / JAN / 01 15:30

- 10 -
9-2
Surveillance / Absence-SET
1. The flashing SET button indicates visitor(s) called during your
absence.
2. Number of visitors is shown on the screen. Example: 2/5
(2nd/# total visits).
3. When motion detection surveillance camera is installed: After 1
minute, the camera is placed in surveillance mode. When
motion detector is activated, inside monitor turns on and a
unique alarm sounds and saves the image.
4. At approx. 1 second after activation, a picture will be taken. If
recording mode is set in 4-frame mode, pictures will be taken
in 4-second intervals, starting at 1 second (1, 5, 9, and 13
seconds after activation).
5. Both alarm sound and image will automatically time out in
approx. 30 seconds. Alarm may be silenced.
6. Press TALK button. The alarm stops. Press TALK again to turn
off image. Communication is not available.
Notes:
•To change setting on camera and motion detector, refer to
instruction manual(s) for those components.
•Automatic update
When capacity is exceeded, the saved pictures will be erased
from the oldest one first, with each new one replacing the oldest
(including non-replayed images).
Note: The image can be saved in memory if needed.
Surveillance-SET (Absence-SET)
Press “SET”button once. The button is lit in red. The system goes
into “Absence-SET”mode or Motion-detection Camera-SET”
mode.
Press “SET”button to reset. The button is no longer lit.
Notes:
Press and hold “SET”button for 2 seconds or more to go into
INITIAL PROGRAM mode.
When “SET”button is flashing, view newly recorded pictures
first by pressing PLAY button.
When the button is steadily lit, press “SET”to return to normal.
9-1
Erase
While replaying
Display the picture to be erased on monitor. Holding down SET
button, press “REC”for 2 sec. Next picture appears. Release
“REC”button.
Note:
This also applies to erasing saved pictures. The picture, once
erased, cannot be restored. One picture in 4-frame mode cannot
be erased, but all four at once.
To erase all the pictures
Return to initial picture save mode, and change to any other
mode (16 in 4-frame, 32, or 60).
8-5
9SURVEILLANCE-SET
[1] [2]
[6]
[5]
2 / 5
Number Total
1/SEP/01 14:30
2/5
[4][3]
PLAY
Prrrrrrrr :1
Prr Prr :2
SET
PLAY
[1] [2]
SET
JA-2MECD JA-2MECD
12 / OCT / 03 14:30 14 / OCT / 03 13:30
2001SEP1 15:30
JA-2MECD
SET
REC

- 11 -
To send video signal to AV equipment
The image on the monitor is printable via composite VIDEO OUT
terminal, connected to a Video printer, etc. (Select a model which
handles NTSC signals).
10-3
10-1
During replay
During replay; When a door station has called or camera has
been activated, it is indicated by an “on-screen”mark, and its call-
in image is viewed and saved automatically. (Replay mode is
ended.) View visitor and communicate.
Notes:
•Room call-in has no on-screen mark shown. The replay mode is
terminated.
•When initiating replay, auto-picture memory (for door call-in) is
not effective for approx. 2 seconds.
10-2
When PLAY & REC buttons are both lit
1. When the system has not been used for months or turned off
for more than 30 minutes after power failure, etc., PLAY &
REC buttons are lit. In this case, press SET button. Two
buttons lights turn off. Set PICTURE MEMORY MODE again.
2. If SET button is still lit or flashing, turn it off by following
these steps: Release SURVEILLANCE-SET mode (Page10).
SET flashes Press PLAY SET lit Press SET SET
light turns off
Notes:
•When changing PICTURE MEMORY MODE, all the pictures
previously saved will be erased.
10 MULTI-MODE OPERATIONS
Specifications
•Power source: DC 24V
•Consumption: (MAX) 750mA (JA-2MECD)
(MAX) 680mA (JA-2MCD).
(MAX) 290mA(JA-2HCD).
•Calling: Chime & image, Approx. 30 sec.
•Communication: AUTO Handsfree voice activation
MANUAL Press to talk, release to listen
•Video-monitor: 4 inch direct view TFT color LCD
•Scanning line: 525 lines
•Door release contact:
AC 12V, 0.35A (dry closure contact L, L).
Run a separate cable for audio/video signal
and door release contact.
•Dimensions: 210H x 160W x 42D(mm).
8-1/4”H x 6-5/16”W x 1-5/8”D.
•Weight: 820g (1.81 lbs.) (aprox.) (JA-2MECD)
770g(1.70 lbs.) (approx.) (JA-2MCD)
730g (1.61 lbs.) (approx.) (JA-2HCD)
Technical Precautions
•Operating temperature: 0°C ~ 40°C (+32°F ~ +104°F).
•Image may vary when Door release button is held down. This is
not a malfunction.
•Cleaning: Clean the units with a soft cloth dampened with
neutral household cleanser. Do not use any abrasive cleaner or
cloth.
•Door station is weather-resistant. But do not spray high-pressure
water on door station directly. Unit trouble could result.
•In case of system malfunction, turn off the power switch of
master station. If this doesn’t solve the problem, disconnect DC
power and contact qualified technician.
11 TECHNICAL PRECAUTIONS
12 SPECIFICATIONS
TALK
BRIGHTNESS
ENTRANCE
MONITOR
ROOM
PLAY
SET
REC
ENTRANCE
RELEASE
DARK
BRIGHTNESS
1
2
VIDEO OUT
JA-2MECD
14 / OCT / 01 13:30
NTSC
14 / OCT / 01 13:30
12 / OCT / 01 14:30
[1]
[2] SET
REC
PLAY
JA-2MECD
PLAY SET
REC
REPLAY
TALK
BRIGHTNESS
ENTRANCE
MONITOR
ROOM
SET
ENTRANCE
RELEASE
DARK
BRIGHTNESS
1
2
SET
SET SET

- 12 -
Aiphone warrants its products to be free from defects of material and
workmanship under normal use and service for a period of two years after
delivery to the ultimate user and will repair free of charge or replace at no
charge, should it become defective upon which examination shall disclose to
be defective and under warranty. Aiphone reserves unto itself the sole right
to make the final decision whether there is a defect in materials and/or
workmanship; and whether or not the product is within the warranty. This
warranty shall not apply to any Aiphone product which has been subject to
misuse, neglect, accident, or to use in violation of instructions furnished, nor
extended to units which have been repaired or altered outside of the factory.
This warranty does not cover batteries or damage caused by batteries used in
connection with the unit. This warranty covers bench repairs only, and any
repairs must be made at the shop or place designated in writing by Aiphone.
Aiphone will not be responsible for any costs incurred involving on site
service calls.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures: •Reorient or relocate the receiving antenna.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. Increase the separation between the
equipment and receiver. •Consult the dealer or an experienced radio/TV
technician for help.
WARRANTY
http://www.aiphone.com/
AIPHONE CO., LTD., NAGOYA, JAPAN
AIPHONE CORPORATION, BELLEVUE, WA, USA
AIPHONE S.A., WISSOUS, CEDEX, FRANCE
Printed in Japan