AIREDALE SmartCool D Instruction Manual

SmartCool™
Downflow – Precision Air C
onditioning
R410A
Installation, M
aintenance and
Commissioning

SmartCoolTM - D Precision Air Conditioning
2
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
About Airedale Products & Customer Services
Warranty
All AIAC products or parts (non consumable) supplied for installation within the UK mainland and
commissioned by an AIAC engineer, carry a full Parts & Labour warranty for a period of 12 months
from the date of commissioning or 18 months from the date of despatch, whichever is the sooner.
Parts or Equipment supplied by AIAC for installation within the UK or for Export that are properly
commissioned in accordance with AIAC standards and specification, not commissioned by an AIAC
engineer; carry a 12 month warranty on non consumable Parts only from the date of commissioning
or 18 months from the date of despatch, whichever is the sooner.
Parts or equipment installed or commissioned not to acceptable AIAC standards or specification
invalidate all warranty.
Warranty is only valid in
the event that
In the period between delivery and commissioning the equipment: is properly protected & serviced as
per the AIAC installation & maintenance manual provided where applicable the glycol content is
maintained to the correct level.
In the event of a problem being reported and once warranty is confirmed as valid under the given
installation and operating conditions, the Company will provide the appropriate warranty coverage
(as detailed above) attributable to the rectification of any affected Airedale equipment supplied
(excluding costs for any specialist access or lifting equipment that must be ordered by the customer).
Any spare part supplied by Airedale under warranty shall be warranted for the unexpired period of
the warranty or 3 months from delivery, whichever period is the longer.
To be read in conjunction with the Airedale Conditions of Sale - Warranty and Warranty Procedure,
available upon request.
CAUTION Warranty cover is not a substitute for maintenance. Warranty cover is conditional to maintenance
being carried out in accordance with the recommendations provided during the warranty period.
Failure to have the maintenance procedures carried out will invalidate the warranty and any liabilities
by Airedale International Air Conditioning Ltd.
Spares
A spares list for 1 3 and 5 years will be supplied with every unit and is also available from our Spares
department on request.
Training
As well as our comprehensive range of products, Airedale offers a modular range of Refrigeration
and Air Conditioning Training courses, for further information please contact Airedale.
Customer Services
For further assistance, please e-mail: [e-mail] or telephone:
UK Sales Enquiries + 44 (0) 113 239 1000 [e-mail]
International Enquiries + 44 (0) 113 239 1000 [e-mail]
Spares Hot Line + 44 (0) 113 238 7878 [e-mail]
Airedale Service + 44 (0) 113 239 1000 [e-mail]
Technical Support + 44 (0) 113 239 1000 [e-mail]
Training Enquiries + 44 (0) 113 239 1000 [e-mail]
For information, visit us at our Web Site: www.airedale.com
Legal Notices
AIAC Ltd endeavours to ensure that the information in this document is correct and fairly stated, but
none of the statements are to be relied upon as a statement or representation of fact. AIAC Ltd does
not accept liability for any error or omission, or for any reliance placed on the information contained
in this document.
The development of Airedale products and services is continuous and the information in this
document may not be up to date. It is important to check the current position with AIAC Ltd at the
address stated. This document is not part of a contract or licence unless expressly agreed.
No part of this document may be reproduced or transmitted in any form or by any means, electronic
or mechanical, including photocopying, recording, or information storage and retrieval systems, for
any purpose other than the purchaser’s personal use, without the express written permission of
AIAC Ltd.
Cover image is the SC25D100-X2X2-0; Controller display is for illustration only.

2013 Airedale International Air Conditioning Limited. All rights reserved. Printed in the UK.

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
3
Installation, Maintenance and Commissioning Manual :6877419 02/2013
About Airedale Products & Customer Services...................................................................... 2
Warranty................................................................................................................................. 2
Spares.................................................................................................................................... 2
Training .................................................................................................................................. 2
Health and Safety....................................................................................................................... 6
Specifier’s Guide Indoor Unit ................................................................................................... 7
Nomenclature......................................................................................................................... 7
Introduction ............................................................................................................................ 8
System Configurations.............................................................................................................. 9
Dual Circuit............................................................................................................................. 9
Dual Cool ............................................................................................................................. 10
Chilled Water........................................................................................................................ 11
Installation Data ....................................................................................................................... 12
Dimensions .......................................................................................................................... 12
Positioning............................................................................................................................ 13
Minimum Unit Clearance...................................................................................................... 13
Electrical Services Incoming Cable ...................................................................................... 14
Incoming Mains Gland Plate ................................................................................................ 14
Weights ................................................................................................................................ 15
Refrigerant Pipe Sizing Guide .............................................................................................. 18
Refrigerant Charging Guide ................................................................................................. 19
Packaged Unit Pre-Charged Refrigerant Volumes............................................................... 21
Design Data – Water Cooled & Free Cooling....................................................................... 22
System Pressure Strength Test ........................................................................................... 23
System Leak Test ................................................................................................................ 23
Evacuation ........................................................................................................................... 24
Refrigerant Handling ............................................................................................................ 25
Oil Charging Guide............................................................................................................... 26
Pressure switch settings....................................................................................................... 26
Compressor Oil Information ................................................................................................. 27
Chilled Water System........................................................................................................... 29
Humidification....................................................................................................................... 29
Condensate Drain Pipework................................................................................................. 32
Fitting Instructions ................................................................................................................ 33
Pipe Clips ............................................................................................................................. 33
Condensate Drain Priming ................................................................................................... 33
Checking for Leaks .............................................................................................................. 33
Condensate Pump Operation............................................................................................... 33
Fan Speeds.......................................................................................................................... 35
Pipework Schematics .............................................................................................................. 47
X2X2 .................................................................................................................................... 48
X2C0 .................................................................................................................................... 49
W2W2 .................................................................................................................................. 50
W2C0 ................................................................................................................................... 51
W2F0.................................................................................................................................... 52
C000..................................................................................................................................... 53
C0C0.................................................................................................................................... 54
Controls .................................................................................................................................... 55
PCO3 CONTROLLER .......................................................................................................... 55
DISPLAY KEYPAD CONNECTIONS ................................................................................... 56
Addressing the Display Keypad ........................................................................................... 57
Use Of Extra Functions Buttons ........................................................................................... 59
Navigation ............................................................................................................................ 59
EVD EVO Driver Setup ........................................................................................................ 60
Removable Plug and Play Display ....................................................................................... 60
Driver Initialization (Driver Reset Function).......................................................................... 61

SmartCoolTM - D Precision Air Conditioning
4
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Input / Outputs...................................................................................................................... 63
Technical Data.......................................................................................................................... 64
System Operating Limits......................................................................................................... 64
Air Cooled Models (X2X2) ....................................................................................................... 65
Performance Data – Air Cooled Models ............................................................................... 65
Mechanical Data- X2X2........................................................................................................ 67
Electrical Data – X2X2.......................................................................................................... 70
Sound Data – X2X2.............................................................................................................. 73
Interconnecting Wiring –X2X2 .............................................................................................. 74
Air Cooled and Chilled Water Models (X2C0) ........................................................................ 76
Performance Data – Air Cooled & Chilled Water Models ..................................................... 76
Mechanical Data –X2C0....................................................................................................... 78
Electrical Data –X2C0 .......................................................................................................... 84
Sound Data – X2C0.............................................................................................................. 90
Waterside pressure drops – X2C0 ....................................................................................... 91
Interconnecting Wiring – X2C0............................................................................................. 92
Water Cooled Models (W2W2)................................................................................................. 94
Performance Data – Water Cooled Models .......................................................................... 94
Mechanical Data – W2W2.................................................................................................... 95
Electrical Data – W2W2........................................................................................................ 98
Sound Data - Water Cooled Models................................................................................... 101
Waterside pressure drop - W2W2 ...................................................................................... 102
Interconnecting Wiring – W2W2 ......................................................................................... 103
Water Cooled and Chilled Water models (W2C0)................................................................ 105
Performance Data –Water Cooled & Chilled Water Models ............................................... 105
Mechanical Data – W2C0................................................................................................... 107
Electrical Data- W2C0 ........................................................................................................ 113
Sound Data – W2C0........................................................................................................... 119
Waterside Pressure Drops W2C0 ...................................................................................... 120
Interconnecting Wiring – W2C0.......................................................................................... 122
Water Cooled and Free Cooling (W2F0)............................................................................... 124
Performance Data – Water Cooled & Free Cooling............................................................ 124
Mechanical Data – W2F0 ................................................................................................... 126
Electrical Data – W2F0....................................................................................................... 132
Sound Data – W2F0........................................................................................................... 138
Waterside Pressure Drops W2F0....................................................................................... 139
Interconnecting Wiring – W2F0 .......................................................................................... 141
Chilled Water Single Circuit (C000) ...................................................................................... 143
Performance Data – Chilled Water – Single Circuit............................................................ 143
Mechanical Data – C000 .................................................................................................... 144
Electrical Data - C000......................................................................................................... 147
Sound Data – C000............................................................................................................ 149
Waterside Pressure Drop C000.......................................................................................... 150
Interconnecting Wiring – C000 ........................................................................................... 151
Chilled Water Dual Circuit (C0C0)......................................................................................... 152
Performance Data – Chilled Water – Dual Circuit .............................................................. 152
Mechanical Data – C0C0.................................................................................................... 153
Electrical Data - C0C0 ........................................................................................................ 156
Sound Data- C0C0 ............................................................................................................. 158
Waterside pressure drop - C0C0........................................................................................ 159
Interconnecting Wiring – C0C0........................................................................................... 160
Commissioning Data ............................................................................................................. 161
Humidifier ........................................................................................................................... 162
Head Pressure Control....................................................................................................... 164

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
5
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Electronically Commutated (EC) Fan Motor ....................................................................... 165
EC Fan interrogation .......................................................................................................... 165
Suction Throttle Valve ........................................................................................................ 166
Hot Gas Re-Heat (HGRH).................................................................................................. 166
Commissioning procedure ................................................................................................... 167
Commissioning Checklist ................................................................................................... 167
Pre Commissioning checks................................................................................................ 167
Fan Section ........................................................................................................................ 168
Chiller /Glycol units ............................................................................................................ 169
Heating............................................................................................................................... 169
Humidification..................................................................................................................... 170
Condenser.......................................................................................................................... 170
Water cooled condenser .................................................................................................... 170
Refrigeration circuit ............................................................................................................ 171
Indoor unit optional extras .................................................................................................. 173
Controls.............................................................................................................................. 174
Maintenance ........................................................................................................................... 175
Filter Changing................................................................................................................... 175
3 Monthly............................................................................................................................ 176
6 Monthly............................................................................................................................ 176
12 Monthly.......................................................................................................................... 176
Humidifier Bottle Change ................................................................................................... 177
Evaporator Fan removal..................................................................................................... 178
Troubleshooting Indoor Unit................................................................................................. 179
Suction throttle valve (STV)................................................................................................ 181
Hot Gas Re-heat (HGRH) .................................................................................................. 181
Humidifier ........................................................................................................................... 181
Unit Alarms:........................................................................................................................ 182
Specifier’s Guide Outdoor unit............................................................................................. 190
Unit Identification................................................................................................................ 190
Standard Features ............................................................................................................. 191
Optional Extras - Energy Saving ........................................................................................ 193
Installation data...................................................................................................................... 194
Dimensions / Weights / Positioning .................................................................................... 194
Unit Lifting .......................................................................................................................... 199
Re-orientation to Vertical Discharge................................................................................... 200
Positioning.......................................................................................................................... 201
Siting Recommendations ................................................................................................... 201
Pipework Connections........................................................................................................ 201
Holding Charge .................................................................................................................. 201
Pipework Installation - Good Practices............................................................................... 201
Performance Data – Condensers....................................................................................... 202
Performance Data – Dry Coolers ....................................................................................... 204
Sound Data ........................................................................................................................ 206
Mechanical Data – Condensers and Dry Coolers .............................................................. 208
Dry Cooler Waterside Pressure Drop................................................................................. 212
Electrical Data .................................................................................................................... 213
Interconnecting Wiring........................................................................................................ 213
Troubleshooting..................................................................................................................... 214
Unmatched Outdoor Units.................................................................................................. 214
Airedale Matched Outdoor Units ........................................................................................ 215
Maintenance ........................................................................................................................... 216

SmartCoolTM - D Precision Air Conditioning
6
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Health and Safety
IMPORTANT
The information contained in this manual is critical to the correct operation and
maintenance of the unit and should be read by all persons responsible for the installation,
commissioning and maintenance of this Airedale unit.
S
afety
The equipment has been designed and manufactured to meet international safety
standards but, like any mechanical/electrical equipment, care must be taken if you are to
obtain the best results.
CAUTION
1
Installation, service and maintenance of Airedale equipment should only be
carried out by technically trained competent personnel.
CAUTION
2
When working with any air conditioning units ensure that the electrical i
solator
is switched off prior to servicing or repair work and that there is no power to
any part of the equipment.
3 Also ensure that there are no other power feeds to the unit such as fire alarm
circuits, BMS circuits etc.
4 Electrical installation commissioning and maintenance work on this equipment
should be undertaken by competent and trained personnel in accordance with local
relevant standards and codes of practice.
5 The refrigerant used in this range of products is classified under the COSHH
regulations as an irritant, with set Workplace Exposure Levels (WEL) for
consideration if this plant is installed in confined or poorly ventilated areas.
6 A full hazard data sheet in accordance with COSHH regulations is available should
this be required.
Protective personal
equipment
Airedale recommends that personal protective equipment is used whilst installing,
maintaining and commissioning equipment.
Refrigerant Warning
The Airedale SmartCool uses R410A refrigerant which is a high pressure refrigerant. It
requires careful attention to proper storage and handling procedures.
Use on manifold gauge sets designed for use with R410A refrigerant. Use only refrigerant
recovery units and cylinders designed for high pressure refrigerants.
R410A must only be charged in the liquid state.
The refrigerant must be stored in a clean, dry area away from sunlight. The refrigerant
must never be stored above 50°C.
Manual Handling
Some operations when servicing or maintaining the unit may require additional assistance
with regard to manual handling. This requirement is down to the discretion of the
engineer. Remember do not perform a lift that exceeds your ability.
Environmental Policy
It is our policy to:
•Take a proactive approach to resolve environmental issues and ensure
compliance with regulatory requirements.
•Train personnel in sound environmental practices.
•Pursue opportunities to conserve resources, prevent pollution and eliminate
waste.
•Manufacture products in a responsible manner with minimum impact on the
environment.
•Reduce our use of chemicals and minimise their release to the environment.
•Measure, control and verify environmental performance through internal and
external audits.
•Continually improve our environmental performance.
General

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
7
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Specifier’s Guide Indoor Unit
Nomenclature
International Example
è
SC19D065 - C000 -0
SC
19
D
065
-
C
0
0
0
-
0
Dual Cool Example
è
SC31D065 - X2C0 -0
SC
31
D
065
-
X
2
C
0
-
0
Mono Cool Example
è
SC25D100 - X2X2 -0
SC
25
D
100
-
X
2
X
2
-
0
SmartCool SC
Decimetre Case Width (dm)
19 - 31
Upflow U
Downflow D
Nominal Capacity (kW) 033-150
Separator -
Air Cooled (Comp Indoor) X
Water Cooled (Comp Indoor) W
Chilled Water C
No Compressor 0
Single Compressor 1
Tandem Compressor 2
Inverter Compressor V
No Option 0
Air Cooled (Comp Indoor) X
Water Cooled (Comp Indoor) W
Free Cooling F
Chilled Water C
No Compressor 0
Single Compressor 1
Tandem Compressor 2
Inverter Compressor V
Seperator -
400V 3PH 50Hz 0
Note
Dual Cool units are defined as those having 2 different cooling mediums (i.e. R410A and Chilled Water [X2C0]).
Dual Circuit units are defined as those having 2 independent cooling circuits (i.e. X2X2 or C0C0).
M o n o / D u a l
( C i r c u i t 1 )
M o n o / D u a l
( C i r c u i t 2 )
V o l t a g e
General

SmartCoolTM - D Precision Air Conditioning
8
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
I
n
troduction
Designed to provide environmental precision air conditioning for applications such as
telecommunication facilities, data centers, computer rooms, clean rooms and
laboratories.
Description Capacity kW (1)
X2X2 Dual circuit direct expansion air cooled 55 -122
X2C0 Dual cool direct expansion air cooled and
chilled water
(X2) 30 – 82.5
(C0) 50 - 102
W2W2 Dual circuit direct expansion water cooled 54 -123
W2C0 Dual cool direct expansion water cooled and
chilled water
(W2) 30 - 85
(C0) 50 - 102
W2F0 Dual cool water cooled and glycol free cooling (W2) 30 - 86
(F0) 50 - 102
C000 Single circuit chilled water 69 -149
C0C0 Dual circuit chilled water 20 -102
(1) Based on nominal unit capacities
Full function units provide full control of temperature, humidity and filtration.
The modular design of the SmartCool allows grouping of differing model types and
capacities to be installed side by side. The flexibility of this type of installation provides for
multi-circuit functionality.
A full range of air cooled condensers is available with the direct expansion indoor units to
provide a matched system with optional performance upgrade, refer to Outdoor Unit
A full range of Dry coolers is available to complement the free cooling indoor units. Dry
coolers are a cost effective and safe solution against legionella.
Also available is a full range of Airedale water chillers to complement the chilled water
indoor units.
The range has been designed and optimised for operation with ozone benign refrigerant
R410A.
CE Directive
Airedale certify that the equipment detailed in this manual conforms with the following
EC Directives:
Electromagnetic Compatibility Directive (EMC) 2004/108/EC
Low Voltage Directive (LVD) 2006/95/EC
Machinery Directive (MD) 89/392/EEC in the version
2006/427/EC
Pressure Equipment Directive (PED) 97/23/EC
To comply with these directives appropriate national & harmonised standards have been
applied. These are listed on the Declaration of Conformity, supplied with each product.
General

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
9
Installation, Maintenance and Commissioning Manual :6877419 02/2013
System Configurations
Dual Circuit
X2X2
The SmartCool X2X2 is an air cooled, direct
expansion (DX), double circuit system linked
to two separate, remotely mounted air cooled
condensers.
Optimised for heat transfer using energy
efficient refrigerant R410A in each circuit, the
X2X2 system is located within the conditioned
space, absorbing room heat and transferring it
outside to the condensers.
By using one or more same/dissimilar sized
scroll compressors across the X2X2 double
circuit, part load efficiency can be maximised
and capacity more precisely matched to
application.
W2W2
Suitable for applications favouring reduced
refrigerant charges, the SmartCool W2W2 is a
double circuit system featuring, DX cooling
within the case and dry coolers outside.
Warm room air is passed through two
completely independent evaporator coils and
an integral plate condenser transfers the heat
load to the glycol solution which is then
channelled outside to two air cooled dry
coolers.
General

SmartCoolTM - D Precision Air Conditioning
10
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Dual Cool
X2C0
For redundancy in critical applications, the SmartCool
dual cool X2C0 offers two different cooling mediums,
air cooled DX and chilled water, within the same case.
The X2C0 system is managed by the Airetronix
microprocessor to select which medium acts as the
primary source of cooling or which acts as back-up,
should the primary source fail or is unable to cope with
the heat load.
W2C0
For applications where a water cooled system is
preferred over air cooled, the SmartCool W2C0
comprises two different cooling mediums within the
same case: DX water cooled, as in the W2W2 system,
and chilled water, as in the C000 system.
The Airetronix microprocessor elects which medium
acts as the primary source of cooling and which as
back-up, if the primary source fails or is unable to cope
with the heat load.
W2F0
The W2F0 system includes a free-cooling coil in
conjunction with the evaporator. In low ambient
conditions, particularly in relation to the high
temperatures and continuous system operation of a
server environment, the W2F0 system will run with
minimum energy. At times of higher ambient,
sophisticated Airetronix controls technology will
modulate the 3-way water regulating valves to
transition from free cooling back to mechanical cooling.
Typically the SmartCool W2F0 single circuit free-
cooling system uses 46%* less energy than a standard
air cooled DX system.
General

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
11
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Chilled Water
C000
Where a chilled water single circuit system is preferred,
warm room air is blown across the efficient cooling coils
of the SmartCool C000 and the heat transferred to a
chilled water system such as Airedale’s high efficiency
TurboChill.
By controlling the 3-way water regulating valve, the
intelligent Airetronix microprocessor can achieve precise
control of temperature and humidity.
C0C0
In the SmartCool C0C0 unit, the cooling coils are split
into two independent systems, each with a 3-way water
regulating valve, and cooled by chilled water from two
separate chillers.
For extra security, the dual circuit configuration of
SmartCool C0C0 offers 2N redundancy.
General

SmartCoolTM - D Precision Air Conditioning
12
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Installation Data
Dimensions
Stan
dard Airflow Configuration (mm)
H x D x W
SC19D mm 1980 x 890 x 1985
SC25D mm 1980 x 890 x 2549
SC31D mm 1980 x 890 x 3113
(1) Forward or reversed air discharge available as standard on all products. Does not require configuring.
(2) Area denotes services entry location. For specific details please contact Airedale.
(3) Open base. Shaded area denotes air discharge.
(4) M6 fixing holes positions for mounting ceiling duct extensions or plenums.
Packed Dimensions
For specific markets units shall be shipped, mounted on wooden pallet and covered with
polythene. The pallet shall be mechanically fixed to the unit for transportation only
(Please contact Airedale for this option)
X = 160mm
Y = 50mm
Z = 50mm
Installation

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
13
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Po
sitioning
Minimum
U
nit
C
learance
Open & Enclosed Floorstand Option
A B C - Floorstand(3)
SC19D
mm 1985 800 Min 200 – Max 750
(+ 50mm Feet Adjustable +/-
20mm) (4)
SC25D
mm 2549 800
SC31D mm 3113 800
Minim
um Ceiling Clearance
-
(D)
Forward Only Forward and 1 Side Forward and 2 Sides All Faces
SC19D
mm 720 500 380 250
SC25D
mm 740 550 440 280
SC31D
mm 750 590 480 300
Notes
(1) Shown with optional open floor stand.
(2) Shaded area indicates minimum service and maintenance requirements. The unit must be installed with allowance for carpet tile clearance.
(3) Dimension C denotes recommended minimum/maximum floor stand height, refer to Airedale for special applications, please specify at order.
(4) Min = Threaded foot at minimum extension (additional to “C” dimension).
Max = Threaded foot at maximum extension (additional to “C” dimension).
(2)
(D)
(1)
Installation

SmartCoolTM - D Precision Air Conditioning
14
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Electrical Services Incoming Cable
Service connections to the smartcool unit are from the left hand side. Provision must be made when sizing cable lengths.
The Floorstand provided by Airedale however has provision for cable entry via the right hand side should it be required,
adjacent to the condensate drain.
Incoming Mains Gland Plate
4 hole centres are punched in the gland plate for
location of cable glands. The plate is removable for
drilling to required size.
Holes1 and 2 for interconnecting wiring to Outdoor unit.
Holes 3 and 4 for Mains incoming Supply A and B
Mains Electrical Incoming Isolator Termination
Mechanical Services Entry + Electrical Option 1
Electrical Services Entry Option 2
Option 1
Option 2
Electrical services through floor stand
(Next to condensate drain)
Installation
2
134

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
15
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Weights
X2X2
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D055-X2X2-0 900 900
SC19D070-X2X2-0 900 910
SC19D080-X2X2-0 900 910
SC25D080-X2X2-0 1020 1020
SC25D090-X2X2-0 1110 1120
SC25D100-X2X2-0 1130 1130
SC31D100-X2X2-0 1280 1290
SC31D120-X2X2-0 1300 1310
SC31D130-X2X2-0 1300 1310
X2C0
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D033-X2C0-0 820 860
SC19D038-X2C0-0 820 860
SC19D045-X2C0-0 820 860
SC19D064-X2C0-0 890 920
SC19D070-X2C0-0 900 930
SC19D076-X2C0-0 900 930
SC25D045-X2C0-0 940 980
SC25D050-X2C0-0 990 1030
SC25D055-X2C0-0 1000 1040
SC25D067-X2C0-0 1010 1050
SC25D073-X2C0-0 1010 1060
SC25D080-X2C0-0 1020 1060
SC31D055-X2C0-0 1150 1200
SC31D065-X2C0-0 1150 1210
SC31D075-X2C0-0 1160 1210
SC31D077-X2C0-0 1170 1220
SC31D080-X2C0-0 1170 1220
SC31D083-X2C0-0 1170 1220
Note
(1) Shipped weights
(2) Installed weight includes refrigerant charges/ internal water volume.
Installation

SmartCoolTM - D Precision Air Conditioning
16
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Weights
W2W2
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D055-W2W2-0 940 940
SC19D070-W2W2-0 970 980
SC19D080-W2W2-0 970 980
SC25D080-W2W2-0 1090 1110
SC25D090-W2W2-0 1220 1230
SC25D100-W2W2-0 1230 1250
SC31D100-W2W2-0 1390 1400
SC31D120-W2W2-0 1400 1410
SC31D130-W2W2-0 1400 1420
W2C0
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D033-W2C0-0 850 880
SC19D038-W2C0-0 860 890
SC19D045-W2C0-0 860 890
SC19D064-W2C0-0 950 980
SC19D070-W2C0-0 950 980
SC19D076-W2C0-0 960 990
SC25D045-W2C0-0 980 1020
SC25D050-W2C0-0 1050 1090
SC25D055-W2C0-0 1050 1100
SC25D067-W2C0-0 1070 1110
SC25D073-W2C0-0 1070 1120
SC25D080-W2C0-0 1080 1120
SC31D055-W2C0-0 1210 1260
SC31D065-W2C0-0 1220 1270
SC31D075-W2C0-0 1220 1270
SC31D077-W2C0-0 1230 1280
SC31D080-W2C0-0 1230 1280
SC31D083-W2C0-0 1230 1290
Note
(1) Shipped weights
(2) Installed weight includes refrigerant charges/ internal water volume.
Installation

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
17
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Weights
W2F0
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D033-W2F0-0 850 880
SC19D038-W2F0-0 860 890
SC19D045-W2F0-0 860 890
SC19D064-W2F0-0 950 980
SC19D070-W2F0-0 950 980
SC19D076-W2F0-0 960 990
SC25D045-W2F0-0 980 1020
SC25D050-W2F0-0 1050 1090
SC25D055-W2F0-0 1050 1100
SC25D067-W2F0-0 1070 1110
SC25D073-W2F0-0 1070 1120
SC25D080-W2F0-0 1080 1120
SC31D055-W2F0-0 1210 1260
SC31D065-W2F0-0 1220 1270
SC31D075-W2F0-0 1220 1270
SC31D077-W2F0-0 1230 1280
SC31D080-W2F0-0 1230 1280
SC31D083-W2F0-0 1230 1290
C000
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D065-C000-0 725 780
SC19D075-C000-0 725 780
SC19D090-C000-0 730 780
SC25D090-C000-0 840 920
SC25D100-C000-0 840 920
SC25D110-C000-0 840 920
SC31D110-C000-0 1000 1080
SC31D130-C000-0 1000 1080
SC31D150-C000-0 1000 1080
C0C0
Unit Shipped Weight (kg) Installed Weight (kg)
SC19D033-C0C0-0 730 790
SC19D038-C0C0-0 730 790
SC19D045-C0C0-0 730 790
SC25D045-C0C0-0 850 930
SC25D050-C0C0-0 850 930
SC25D055-C0C0-0 850 930
SC31D055-C0C0-0 1010 1100
SC31D065-C0C0-0 1010 1100
SC31D075-C0C0-0 1010 1100
Note
(1) Shipped weights
(2) Installed weight includes refrigerant charges/ internal water volumes.
Installation

SmartCoolTM - D Precision Air Conditioning
18
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Refrigerant Pipe Sizing Guide
The refrigerant pipe sizing information below is for a guide only. Pipe sizes based on 100% load.
Equivalent Pipe Lengths with R410A
Indoor
Unit
Outdoor
Unit
Indoor Unit
Connection Size 0-15m Discharge 15-40m Discharge
Liquid Disch
Liquid
(3)
Horizontal
(1)
Vertical
(2)
Liquid
(3)
Horizontal
(1)
Vertical
(2)
SC19D055-X2X2-0 CR50 1/2" 7/8" 5/8" 7/8" 3/4" 5/8" 7/8" 7/8"
SC19D070-X2X2-0 CR65 5/8" 7/8" 5/8" 7/8" 7/8" 5/8" 7/8" 7/8"
SC19D080-X2X2-0 CR65 5/8" 7/8" 5/8" 7/8" 7/8" 3/4" 7/8" 7/8"
SC25D080-X2X2-0 CR65 5/8" 7/8" 5/8" 7/8" 7/8" 3/4" 7/8" 7/8"
SC25D090-X2X2-0 CR65 7/8" 1 1/8" 5/8" 7/8" 7/8" 3/4" 7/8" 7/8"
SC25D100-X2X2-0 CR80 7/8" 1 1/8" 3/4" 1 1/8" 1 1/8" 3/4" 1 1/8" 1 1/8"
SC31D100-X2X2-0 CR80 7/8" 1 1/8" 3/4" 1 1/8" 1 1/8" 3/4" 1 1/8" 1 1/8"
SC31D120-X2X2-0 CR105 7/8" 1 1/8" 3/4" 1 1/8" 1 1/8" 3/4" 1 1/8" 1 1/8"
SC31D130-X2X2-0 CR105 7/8" 1 1/8" 3/4" 1 1/8" 1 1/8" 7/8" 1 1/8" 1 1/8"
SC19D033-X2C0-0 CR50 1/2" 7/8" 5/8" 7/8" 3/4" 5/8" 7/8" 7/8"
SC19D038-X2C0-0 CR65 5/8" 7/8" 5/8" 7/8" 7/8" 5/8" 7/8" 7/8"
SC19D045-X2C0-0 CR65 5/8" 7/8" 5/8" 7/8" 7/8" 3/4" 7/8" 7/8"
SC19D064-X2C0-0 CR105 5/8" 7/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC19D070-X2C0-0 CR105 7/8" 1 1/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC19D076-X2C0-0 CR105 7/8" 1 1/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC25D045-X2C0-0 CR65 7/8" 1 1/8" 5/8" 7/8" 7/8" 3/4" 7/8" 7/8"
SC25D050-X2C0-0 CR65 7/8" 1 1/8" 5/8" 7/8" 7/8" 3/4" 7/8" 7/8"
SC25D055-X2C0-0 CR80 7/8" 1 1/8" 3/4" 1 1/8" 1 1/8" 3/4" 1 1/8" 1 1/8"
SC25D067-X2C0-0 CR105 7/8" 1 3/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC25D073-X2C0-0 CR105 7/8" 1 3/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC25D080-X2C0-0 CR105 7/8" 1 3/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC31D055-X2C0-0 CR80 7/8" 1 3/8" 3/4" 1 1/8" 1 1/8" 3/4" 1 1/8" 1 1/8"
SC31D065-X2C0-0 CR105 7/8" 1 3/8" 3/4" 1 1/8" 1 1/8" 3/4" 1 1/8" 1 1/8"
SC31D075-X2C0-0 CR105 7/8" 1 3/8" 3/4" 1 1/8" 1 1/8" 7/8" 1 1/8" 1 1/8"
SC31D077-X2C0-0 CR105 7/8" 1 3/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC31D080-X2C0-0 CR105 7/8" 1 3/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
SC31D083-X2C0-0 CR105 7/8" 1 3/8" 3/4” 1 1/8” 1 1/8” 7/8” 1 3/8” 1 1/8”
(1) For interconnecting pipework with a predominantly horizontal layout.
(2) For interconnecting pipework with a predominantly vertical layout.
(3) Careful pipework selection must be done if the liquid line rises. Additional system sub cooling may be required to overcome friction losses.
IMPORTANT
Tandem Compressor and suction throttle valve applications:
In part load, gas velocity should be taken into account when selecting and commissioning
pipework to ensure full oil return.
REMEM
BER excessive pressure loss in interconnecting pipework will impair system
performance; this should be factored in during the design of the system and where
necessary oil separators employed.
Excessive pressure drop in liquid lines can cause poor refrigerant distribution to
expansion devices and can cause malfunction of the system (especially with condensers
lower than the evaporator)
Oil Traps
For long vertical rises in both liquid and discharge lines, it is essential that oil traps are
located every 4m to ensure proper oil movement / entrapment. In addition there should be
an oil trap at the exit of the air handling unit before a vertical riser is applied (refer to
example below).
Pipe Supports
The following table identifies the maximum
distance between pipe supports on vertical
and horizontal pipe runs.
Pipe O/D (inches) Support distance (m)
3/8 - 7/8 1.0
1 1/8 - 2 1/8 2.0
CAUTION
All pipework should be clamped prior to insulation being applied. Clamping over
insulation is not acceptable.
Horizontal Sections
It is good practice to ensure a slight gradient toward the compressor in the direction of the
refrigerant flow for suction lines running horizontal. This assists oil return to the
compressor. A gradient of approximately 1:200 (0.5%) shall be used.
Installation

Precision Air Conditioning SmartCoolTM – D
Precision Air Conditioning
19
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Liquid Line
If the system is configured with the SmartCool higher than the condenser unit h it may
be required to increase the degree of sub cooling to prevent flashing gas. This flashing is
caused by excess pressure drop caused by the static head of refrigerant and can cause
poor operation of the evaporator and metering device.
Careful pipe sizing is recommended to ensure that the liquid does not form gas due to
excess pressure drop
Increasing the liquid line size minimizes pipe friction and flashing due to friction pressure
drop.
However as a fail safe it is recommended that the condenser is installed below the
indoor unit to allow for correct liquid drain.
Pipe Insulation
The liquid line of the system must be insulated if passing through extremely warm places
(Boiler houses etc). Ensuring that the refrigerant does not become flash gas.
Condenser above Air Handling Unit
Condenser below Air Handling Unit
t
4m
t
Discharge Line Liquid Diagrams above for illustration only
Refrigerant
C
harging Guide
The following information can be used to estimate the refrigerant quantity required in a
typical split system installation.
Unit
Refrigerant
Charge
(kg/Circuit)
The following table shows the refrigerant charge / circuit for the indoor and outdoor units.
Indoor Unit Standard Condenser Larger Condenser
(Indoor Unit) kg/Circuit
HGRH
(1)
kg/Circuit (Outdoor Unit) kg/Circuit (Outdoor Unit) kg/Circuit
SC19D055-X2X2 4.41 4.56 CR50 4.9 CR65 9.78
SC19D070-X2X2 4.66 4.81 CR65 9.78 CR80 8.37
SC19D080-X2X2 4.66 4.81 CR65 9.78 CR80 8.37
SC25D080-X2X2 5.84 6.04 CR65 9.78 CR80 8.37
SC25D090-X2X2 6.37 6.60 CR65 9.78 CR80 8.37
SC25D100-X2X2 6.38 6.60 CR80 8.37 CR105 16.72
SC31D100-X2X2 7.56 7.83 CR80 8.37 CR105 16.72
SC31D120-X2X2 7.57 7.83 CR105 16.72 CR130 22.05
SC31D130-X2X2 7.67 7.94 CR105 16.72 CR130 22.05
SC19D033-X2C0 4.34 4.49 CR50 4.9 CR65 9.78
SC19D038-X2C0 4.59 4.74 CR65 9.78 CR80 8.37
SC19D045-X2C0 4.59 4.74 CR65 9.78 CR80 8.37
SC19D064-X2C0 5.13 5.33 CR105 16.72 CR130 22.05
SC19D070-X2C0 5.13 5.34 CR105 16.72 CR130 22.05
SC19D076-X2C0 5.14 5.34 CR105 16.72 CR130 22.05
SC25D045-X2C0 5.77 5.97 CR65 9.78 CR80 8.37
SC25D050-X2C0 6.31 6.53 CR65 8.37 CR80 8.37
SC25D055-X2C0 6.31 6.53 CR80 8.37 CR105 16.72
SC25D067-X2C0 6.31 6.56 CR105 16.72 CR130 22.05
SC25D073-X2C0 6.32 6.57 CR105 16.72 CR130 22.05
SC25D080-X2C0 6.32 6.57 CR105 16.72 CR130 22.05
SC31D055-X2C0 7.49 7.75 CR80 8.37 CR105 16.72
SC31D065-X2C0 7.49 7.76 CR105 16.72 CR130 22.05
SC31D075-X2C0 7.49 7.76 CR105 16.72 CR130 22.05
SC31D077-X2C0 7.50 7.79 CR105 16.72 CR130 22.05
SC31D080-X2C0 7.50 7.79 CR105 16.72 CR130 22.05
SC31D083-X2C0 7.50 7.79 CR105 16.72 CR130 22.05
(1)Fitted with optional hot gas re-heat
Installation
Warning: May have flash gas occurring
in liquid line if riser friction losses are
excessive.

SmartCoolTM - D Precision Air Conditioning
20
Precision Air Conditioning
Installation, Maintenance and Commissioning Manual :6877419 02/2013
Liquid
Line
Refrigerant
Charge (kg/m)
The following table shows the refrigerant charge / metre for the liquid line, using R410A
and assuming a liquid line temperature of 40°C.
Liquid Line (m) kg/m
3/8” 0.05
1/2” 0.09
5/8” 0.15
3/4” 0.21
7/8” 0.30
1 1/8” 0.53
IMPORTANT
The pipe
sizes/refrigerant charges quoted are for guidance only. It is the responsibility of
the installing contractor/site engineer to check the pipe sizes/refrigerant charges are correct
for each system installation and application. Excess pressure drop on a system may require
additional refrigerant charges to ensure correct unit operation.
Split systems may require additional oil which should be added to the low side of
each compressor.
Design should be in accordance with accepted refrigeration prac
tice to ensure good oil
return to the compressor(s) under all normal operating conditions.
Calculation of
Liquid Line
Refrigerant Charge (kg)
The liquid line refrigerant charge can be calculated using the following equation:
LR = L x m Where:
LR = Total Liquid Line Refrigerant charge (kg)
L = Length of Interconnecting pipework (metres)
m = Liquid Line Refrigerant charge / metre. Refer to
Liquid Line Refrigerant
Charge (kg/m), above.
Calculation of
System
Refrigerant Charge (kg)
The system refrigerant charge can be calculated using the following equation:
SR = LR + IR + OR Where:
SR = Total System Refrigerant charge (kg)
LR = Total Liquid Line Refrigerant charge. (As calculated from above)
IR = Indoor Unit Refrigerant Charge.
OR = Outdoor Unit Refrigerant Charge.
Example
Indoor Unit Model Ref. = SC19D055-X2X2-0
Outdoor Unit Model Ref. = CR50 Condenser
Interconnecting Pipework = 10 metres
Selecting The Liquid Line Size
From the Refrigerant Pipe Sizing Guide, the liquid line size given for pipework length of 10 metres
is:
Liquid Line Size = 5/8”
Liquid Line Refrigerant
Charge
LR = L x m Where:
L = 10 metres
m = 0.15 kg/m
LR = 10 x 0.15 Liquid Line Charge = 1.5 kg
System Refrigerant Charge
SR = LR + IR + OR Where:
LR = 1.5 kg. (As calculated from above)
IR = 4.41 kg
OR = 4.9 kg
SR = 1.5 + 5.57 + 4.9 System Refrigerant Charge = 10.81kg / Circuit
Installation