AIRINNOVATIONS CLEAN MIST MH-702A Instruction Manual

nished size 5.5” wide x 8.5” high
CLEAN MIST™SMART HUMIDIFIER™
WITH REMOTE CONTROL & AROMA TRAY
TABLETOP & FLOOR STANDING
Instruction Manual and Warranty Information
READ AND SAVE THESE INSTRUCTIONS
nished size 5.5” wide x 8.5” high

Contents
Safety Instructions ............................................................................................................. 1
Unpacking / Specications ............................................................................................... 2
Parts & Contents ............................................................................................................... 3
Filling The Water Tank ....................................................................................................... 4
Operating Instructions ....................................................................................................... 5
Weekly Cleaning & Care / Storage .................................................................................... 6
Troubleshooting ................................................................................................................. 7
Other Great Products ........................................................................................................ 8
Warranty ............................................................................................................................ 9
If you have a respiratory condition, please contact your physician prior to use.
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 18 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.This product has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 18 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that the interference will not occur in a particular installation. If the product does cause harmful interference to
radio or television reception, which can be determined by turning the product on or o, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

1
SAFETY INSTRUCTIONS
• This appliance has a polarized plug (one blade is wider than the other) as a safety
feature. If the plug does not t fully into the outlet, reverse the plug. If it still doesn’t
t, contact a qualied electrician. DO NOT attempt to defeat this safety feature.
• Before using the humidier, extend the cord and inspect for any signs of damage;
DO NOT use if the cord has been damaged.
• Keep cord away from heated surfaces and out of the way, where it cannot be
stepped on or tripped over.
• NEVER use in an environment where explosive gases are present.
• Place humidier on a stable level surface; DO NOT place on carpet, next to
heating vents, under direct sunlight, in high temperature areas, or near computers
and electronic equipment.
• DO NOT place the the humidier directly on wood furniture or other surfaces which
could get damaged by water.
• DO NOT direct the mist against a wall or home appliances.
• NEVER operate without water in the Tank; DO NOT use anything other than room
temperature tap or distilled water.
• NEVER add essential oils directly to the water, as this will damage the unit and void
the warranty.
• DO NOT touch the water in the Base during operation.
• DO NOT expose or immerse the Base in water when cleaning.
• DO NOT pour water into the base through the Air Outlet during cleaning and lling.
• NEVER block the Air Outlet or intake or cover the unit when it’s in operation
• DO NOT use any attachments not provided with the unit.
• Discontinue use if humidier makes loud noises or has a strange smell.
• DO NOT attempt to repair or adjust the unit; servicing must be performed by
professional or qualied personnel.
Battery Disposal:
DO NOT dispose of batteries in re. Improper handling/disposal of batteries may cause
batteries to explode or leak. Please dispose of batteries responsibly by throwing away
batteries in a proper trash receptacle per township ordinance.
• Only operate when fully assembled; only use as intended and described in this manual.
• Keep out of reach of small children.
• Always insert plug securely into the power source.
• Unplug the unit and empty the Water Tank and Base before carrying/moving.
• Only unplug when the humidier is turned o; ensure hands are dry.
• Always turn o the unit before removing, emptying or lling the Water Tank.
• Perform regular maintenance of the Ultrasonic Nebulizer; NEVER scrape Nebulizer with
a hard or sharp object.
• Dry the unit completely before storage; store in a cool, dry place.
• Do not drop, hit or otherwise subject this product to excessive shock.
READ AND SAVE THESE INSTRUCTIONS: Failure to follow
all the instructions may result in electrical shock.
WARNING
CAUTION

No More Dry Air
Thank you for choosing the Air Innovations® – Clean Mist™ SMART Humidier™ With
Remote Control & Aroma Tray and congratulations on taking this important step in
improving the quality of air in your home or oce.
The Air Innovations® – Clean Mist™ SMART Humidier™ uses Ultrasonic Technology to
create humidity instantaneously, while working silently to erase the discomforts of dry air.
Unpacking
*Follow directions to ll and operate the humidier.
2
Remove the Remote Control and Dual Directional
Mist Nozzle from the top of the packaging.
Remove the plastic bag
from the humidier.
Carefully remove the Extension
Nozzle and humidier from the
box by pulling the Base of the
unit (Do not take the unit out
of the box by pulling the tank).
1
2
3
Product Model Power Consumption Current Rating Voltage Tank Capacity Dimensions Weight
MH-702A 30W 0.4A 110-120V~60Hz 6.5L / 1.7 Gallon 8.25”W x 8.25”D
x 19.75” H
3.83 Lbs.
Specications

1. Dual Directional Mist Nozzle
2. Extension Nozzle
3. Handle
4. Water Tank
5. Water Window
6. Aroma Tray
7. Base
8. Control Panel
9. Remote Control
10. Air Outlet
11. Water Sensor
12. Ultrasonic Nebulizer
13. Water Reservoir
14. Cleaning Brush
15. Ceramic Filter
16. Tank Cap
17. Bottom Tank Handle
3
Parts & Contents
11
10
13
12
14
15
16
(requires (1) 3V Lithium Battery included)
17
2
4
3
3
5
6
1
7
89

Replace the Tank Cap by
rmly turning clockwise until
tight. Turn the Water Tank
upright and check the Tank
Cap for leaks. If any water
drips, remove the Tank Cap
and retighten. WARNING:
DO NOT place Water Tank on
the humidier Base if the cap
is leaking.
When replacing the Water Tank
on the Base, lift the handle up
and align the notches on the
front of the Water Tank and
Base. Ensure the tank is rmly
seated.
Make sure the handle is
snapped back into place, then
turn the Water Tank upside
down and remove the Tank Cap
by turning it counter clockwise.
Remove Extension Nozzle and
Dual Directional Mist Nozzle
prior to lling the Water Tank.
1
Lift the Handle on top of the
Water Tank to remove the
humidier from the Base.
2 3
4
4
56
Filling The Water Tank
WARNING: Always unplug the unit before removing the Water Tank.
WARNING: DO NOT touch the water in the Base.
WARNING: NEVER ll the Water Tank from the top of the unit. Follow Water Tank
lling instructions in #4.
Filling the Water Tank:
Use clean, cool, tap water.
WARNING: DO NOT
use
extremely cold water, since it may
temporarily reduce the mist output.
WARNING:
NEVER ll with
hot/warm water or use additives
as this could damage the unit and
void the warranty.
WARNING: If you have
hard tap water use our
Humidier Demineralization
Filters (available at
www.Air-Innovations.com) or
use ONLY ltered
/distilled water.
7
Attach the Dual Directional Mist Nozzle to the top of the Water Tank. To easily control the direction of
the mist simply separate the Dual Directional Mist Nozzle and position as desired-see photo above.
Extension Nozzle – To convert this unit from a Tabletop unit to Floor unit simply remove the Dual
Directional Mist Nozzle from the top of the Water Tank. Place the unit on your desired oor area and
insert the Extension Nozzle into the Top of the Water Tank. Then place the Dual Directional Nozzle on
the top of the Extension Nozzle.

5
Remote
Control
Be sure to remove
the clear pull tab
before using the
remote.The func
-
tions on the Remote
Control mirror those
on the humidi
-
er. When using the
Remote Control,
you can control the
humidier from your
desired location.
Operating Instructions
1
6
7
5
4
2
3
Mist Output – When you turn the unit ON, it will default to
the lowest mist setting. Pressing the Mist button each time
will increase the output. Press once for Medium, twice for
High, three times for Supreme, four times for Turbo. Pressing
the Mist button a fth time will bring the unit back to Low.
The Delay Start and Auto-O buttons allow you to set the humidier to turn ON and
OFF automatically as desired.
Delay Start – The Delay Start feature allows you to program the unit to turn ON
automatically. To use, press the Delay Start button once; you will see Delay Start
01:00H illuminated on the display. This feature works in 1 hour
increments and is programmable up to 24 hours. Simply keep pressing the Delay
Start button until you get to your desired delay start time, once you have reached
the time the display will ash three times and then will start to countdown until
the unit turns ON.
Auto-O – The Auto-O feature allows you to run the humidier now and set it to turn
OFF at a specic time automatically (in 1 hour increments from 1-24 hours).To use -
press the Auto-O button once; you will see Auto-O 01:00H illuminated on the display.
This feature works in 1 hour increments and is programmable up to 24 hours. Simply
keep pressing the Auto-O button until you get to your desired Auto-O time. Once you
have reached the time the display will ash three times and then start to count down
until the unit turns OFF. The display will start alternating between the current ambient
humidity and the Auto-O Timer. NOTE: You can use the Delay Start and Auto-O
functions together on this fully programmable LED Display to program the humidier to
turn ON and turn OFF at your desired times.
Beep/Dim – The humidier automatically defaults to an audible beep when
changing settings. The waterless indicator will illuminate and you will hear three beeps
when the humidier is out of water and the LED Display will be illuminated.To disable
one or more of these settings, follow the steps below: Press Beep/Dim once to disable all
sound (Beep O will ash on the display three times and then will remain on the display
to indicate the sound is OFF). Press the button twice to turn the LED Display OFF (sound will
remain OFF) and press a third time to enable the LED Display and the sound (default function).
Low Water – When the tank is out of water the “Waterless” indicator will appear in
the display, you will hear three beeps and the automatic safety shut-o will turn the
Ultrasonic Nebulizer & unit OFF. Note: You can disable the audible beep by pressing the
Beep/Dim button once. To re-enable, press the Beep/Dim button two more times.
ON/OFF –
Plug into a standard (120V AC) electrical
outlet. The LED Display will turn ON for 2 seconds then turn
OFF. Press the ON/OFF button once and the “Operating”
indicator will turn ON. Mist may not appear immediately;
allow up to 15 minutes for the water in the tank to transfer
to the base.
NOTE: During the rst use you may hear several beeps
and the “Waterless” indicator may illuminate before mist
appears.
Humidistat – By using this feature the humidier will automatically monitor and
control the humidity level according to your desired setting. Once the desired humidity
level is reached the mist will shut OFF until the humidity drops below the setting and
then the mist will turn back ON automatically to maintain the humidity level desired.
To set this feature press the Humidistat button to your desired setting. Settings range
from 40%-95% RH (Relative Humidity) in 5% RH increments. A 40%-60% Relative
Humidity is recommended. Once you set your desired humidity, the number will ash
three times and then the display will revert back to the Relative Humidity. To view the
set humidity level, press the Humidistat button once.
Extra Features
Safety Shut O
Automatic Use
Manual Use
AROMA
TRAY
Aroma Tray- By inserting an Air Innovations Essential Oil Aroma Pad into the built-in
aroma tray, you can transform your humidier into an easy-to-use fragrance dispenser.
Visit www.Air-Innovations.com to purchase Aroma Pads.
W
ARNING: DO NOT operate the humidier without water in the tank. WARNING: NEVER lift the tank o the Base while the unit is operating.

1. Follow all cleaning instructions prior to storage.
2. Dry all parts, including the inside of the Water Tank.
3. Leave the tank cap partially loosened to prolong the life of the cap.
4. Preferably store in its original box, in a dry place away from high temperatures.
5. Follow all cleaning instructions after long periods of storage.
a
e
b
dc
6
Storage
fg h i
Replacing The Remote Control Battery - Push the tab to the left of the
battery tray towards the right to unlock the tray.
f
While the the tab is pushed,
pull out the battery tray.
g
Remove the battery from the tray and replace it with
a new 3.5 volt lithium battery (CR2025) with the positive side facing up.
h
Insert
the tray back into the bottom of the remote contol until it locks in.
i
Weekly Cleaning & Care
WARNING: Before cleaning always turn power o and unplug the unit from outlet.
WARNING: DO NOT rinse Base under faucet. To clean, wipe the Base with a soft cloth.
WARNING: DO NOT use any solvents or aggressive cleaning agents. Keep water away from the Air Outlet.
WARNING: DO NOT tamper with the Water Sensor.
About White Dust -Use of high-mineral content water may cause a white mineral residue to
accumulate on room surfaces near the humidier. The mineral residue is commonly referred to as “White Dust”. The higher the
mineral content (the harder your water is), the greater the potential for White Dust. The White Dust is not caused by a defect
in the humidier, but is due only to minerals suspended in the water from your tap. WARNING: If you have hard tap water
STOP using tap water and visit our website (www.Air-Innovations.com) to purchase our Humidier Demineralization Filters or
use ONLY ltered or distilled water.
Tank Cleaning - Remove the Mist Nozzle from the top of the Water Tank then remove the Water Tank from the
unit. Turn the tank upside down, unscrew the Tank Cap and drain any water from the tank. Wipe the tank with
a soft damp cloth then rinse it with warm water inside and out.
Base Cleaning - Gently wipe the Base with a soft damp cloth.
White Dust Cleaning - If mineral deposits “White Dust”
are evident around the Ultrasonic Nebulizer
a
and Water Sensor,
clean these surfaces with a soft cloth and a small amount of
undiluted white vinegar. If necessary, mix a solution of 50%
white vinegar and 50% water and ll the Base with enough
solution to cover the Ultrasonic Nebulizer
a
. Allow it to soak for
an hour and then use the provided brush to gently loosen
build up on the Ultrasonic Nebulizer
b
. Put 1 cup of water in the
Base and wipe clean with a soft cloth. WARNING: DO NOT
rinse Base under faucet.
Ceramic Water Filter Cleaning - Remove the Water Tank from
the humidier Base. Remove the Tank Cap
c
and rinse Ceramic
Filter thoroughly with tap water
d
, then replace on Water Tank.
Surface Cleaning - Clean all surfaces of the unit with a clean
damp soft cloth.
WARNING: When emptying the Water Reservoir on the Base,
make sure that the water is poured away from the Air Outlet
e
.
If water is poured into the outlet it may damage the humidier.

Troubleshooting
7
Problem Solution
Weak or no mist output. The water in the unit is too cold: Replace with cool but not
cold water or set output to High and wait 10-15 minutes.
The surface of the Ultrasonic Nebulizer is dirty: Clean Ultra-
sonic Nebulizer. (see pg. 6 “White Dust Cleaning”)
Ultrasonic Nebulizer is not working: See Warranty.
White dust is forming on
nearby furniture.
Hard tap water may deposit a certain amount of dust. Visit our
website (www.Air-Innovations.com) to purchase Humidier
Demineralization Filters or use distilled water.
Water is leaking. Water Tank Installation: Make sure the tank is correctly
attached. (see pg. 4 “Filling the Water Tank”)
Humidier is not on a level surface: Place on a level surface.
Condensation is forming
around humidier or
windows.
Mist output level is too high for room size: Decrease the mist
output.
Direction of Rotating Mist Nozzle: Change direction of nozzle.
Aroma Tray does not close. Aroma Pad is not seated properly: Remove and reinsert the
pad.
Missing parts. Call us toll free at: 844-600-1370, Monday thru Friday
8:30am to 5pm EST.
Please reference model: MH-702A

8
Try These Other Great
Products For Your Life!
Available at: www.ForLifeProducts.com, www.Air-Innovations.com, www.Pursfection.com, www.RejuvenateProducts.com

1-YEAR WARRANTY - MH-702A
Air Innovations® Clean Mist™ SMART Humidier™ with Remote Control & Aroma Tray
comes with a 1-year manufacturer’s warranty. If this unit should become defective within
1-year from the date of purchase, or if you have any questions or comments or regarding
replacements for any of our products, please contact us directly at:
Call us toll free at: 844-600-1370
Monday thru Friday 8:30 AM to 5:00 PM EST.
Visit us on the web at: www.Air-Innovations.com
e-mail us: [e-mail]
Or write us:
Air Innovations
Att: Quality Assurance Dept.
2301 SW 145th Ave.
Miramar, FL. 33027 USA
Please ll out the warranty card and
mail back to the above address.
Or, register your warranty online today.
Simply go to:
www.Air-Innovations.com
NAME
ADDRESS
CITY
STATE ZIP
TELEPHONE
E-MAIL
DATE OF PURCHASE
PLACE OF PURCHASE
THIS UNIT COMES WITH A 1-YEAR WARRANTY SUBJECT TO THE FOLLOWING CONDITIONS:
In the rst year, all repairs will be performed free of charge or the unit will be replaced. This warranty
is not transferable, it is valid only for the original purchaser. This warranty will be voided if the unit is
subjected to unauthorized repair or impact damage. If you have any questions please call toll free:
844-600-1370. This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
Please check here if you would not like to receive any solicitations from our company
!
9

Air Innovations® ©2018 Great Innovations, LLC. All Rights Reserved. US & International Patents Pending. Printed in China.
Available In A Variety Of Colors