AIRINNOVATIONS CLEAN MIST SMART HUMIDIFIER MH-512A Platinum Instruction Manual

CLEAN MIST™SMART HUMIDIFIER™
Instruction Manual and Warranty Information
IM0031B READ AND SAVE THESE INSTRUCTIONS
nished size 5.5” wide x 8.5” high

Contents
Safety Instructions ............................................................................................................. 1
Unpacking / Specications ............................................................................................... 2
Parts & Contents ............................................................................................................... 3
Filling The Water Tank ....................................................................................................... 4
Operating Instructions ....................................................................................................... 5
Weekly Cleaning & Care / Storage .................................................................................... 6
Troubleshooting ................................................................................................................. 7
Other Great Products ........................................................................................................ 8
Warranty ............................................................................................................................ 9
If you have a respiratory condition, please contact your physician prior to use.
FCC STATEMENT
Potential for Radio/Television interference
This device complies with Part 18 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.This product has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 18 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
The product generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that the interference will not occur in a particular installation. If the product does cause harmful interference to
radio or television reception, which can be determined by turning the product on or o, the user is encouraged to
try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
• Changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

SAFETY INSTRUCTIONS
1
Prior to using the appliance, read through the instructions for complete use and
keep in a safe place for later reference.
• WARNING: DO NOT use outdoors. Only use as intended and described
in this manual.
• WARNING: DO NOT expose or immerse the Base in water or other liquids.
• Before using the appliance, extend the cord and inspect for any signs of
damage. WARNING: DO NOT use if cord has been damaged.
• WARNING: Keep cord away from heated surfaces and out of the way,
where it cannot be stepped on or tripped over.
• WARNING: This appliance has a polarized plug (one blade is wider than the other)
as a safety feature. If the plug does not t fully into the outlet, reverse the plug.
If it still doesn’t t, contact a qualied electrician. WARNING: DO NOT attempt
to defeat this safety feature.
• WARNING: ALWAYS place humidier on an elevated rm, at, level surface
where it’s not easily knocked over. (e.g. on a table, chest, cabinet, etc).
• WARNING: DO NOT place the appliance directly on the oor, next to a heating
vent, under direct sunlight, high temperature areas, near computers or sensitive
electronic equipment.
• WARNING: DO NOT place the appliance directly on wood furniture or other
surfaces which could get damaged by water.
• WARNING: NEVER use in an environment where explosive gases are present.
• WARNING: DO NOT use any attachments not provided with the unit.
• WARNING: NEVER use the appliance after a malfunction, after it has been
dropped or damaged in any other way.
• Only operate when fully assembled.
• Keep out of reach of children. Close supervision is necessary when this
appliance is used by or near children, elderly or disabled persons.
• WARNING: NEVER drop or insert any object into any opening.
• WARNING: DO NOT block any air outlets or intakes.
• WARNING: NEVER cover the appliance when it’s in operation.
• WARNING: To unplug turn controls to the “OFF” position, then remove the plug
from the outlet. Ensure your hands are dry.
• WARNING: ALWAYS unplug and EMPTY the Water Tank when not in use for a
long period of time.
• WARNING: ALWAYS turn o or unplug before removing, lling or emptying
the Water Tank.
• WARNING: DO NOT wash, adjust or move without rst unplugging the unit.
• WARNING: DO NOT touch the water or any other part in the Base
during operation.
• WARNING: NEVER operate WITHOUT water in the tank.
• WARNING: DO NOT use hot water in the tank.
• WARNING: ONLY use water in the tank, never use any additive such as
essential oils, eucalyptus, water conditioners, etc… in the water.
• WARNING: DO NOT move appliance with water inside the tank. In this case
remove the Water Tank and empty the Water Reservoir prior to moving.
• WARNING: DO NOT attempt to repair or adjust the unit. Servicing must be
performed by professional or qualied personnel.
• WARNING: Discontinue use if unit makes loud noises or has a strange smell.
• Perform regular maintenance of the Ultrasonic Nebulizer.
• WARNING: DO NOT direct the mist against a wall or other home appliance.
• WARNING: DO NOT pour water into the Base through Air Outlet during
cleaning and lling.
• WARNING: DO NOT rinse Base under faucet.
• WARNING: DO NOT immerse the Base in water.
• WARNING: NEVER scrape the Ultrasonic Nebulizer with a hard or sharp object.

No More Dry Air
Thank you for choosing the Air Innovations® – Clean Mist™ Smart Humidier™ and
congratulations on taking this important step in improving the quality of air in your
home or oce.
The Air Innovations® – Clean Mist™ Smart Humidier™ uses Ultrasonic Technology to
create humidity instantaneously, while working silently to erase the discomforts of dry air.
Unpacking
Specications
Product Model Power Consumption Rating Voltage Tank Capacity Dimensions Weight
MH-512 30W 110-120V~60Hz 5.7L / 1.5 Gallon L10.25” X W6”
X H15.75”
3.3 Lbs
*Follow directions to ll and operate the humidier.
2
Open the box and remove
packing material.
Remove the plastic bag
from the humidier.
Carefully remove the humidier from
the box by pulling the Base of the unit
(Do not take the unit out of the box
by pulling the tank).
1
2
3

8
11
12
13
1. Rotating Mist Nozzle
2. Handle
3. Water Tank
4. Base
5. Control Panel
6. Ultrasonic Nebulizer
7. Air Outlet
8. Water Sensor
9. Water Reservoir
10. Cleaning Brush
11. Ceramic Filter
12. Tank Cap
13. Bottom Tank Handle
3
Parts & Contents
7
6
9
10
12
2
3
4
5

Filling The Water Tank
4
WARNING: Always unplug the unit before removing the Water Tank.
WARNING: DO NOT touch the water in the Base.
WARNING: NEVER ll the Water Tank from the top of the unit. Follow Water Tank
lling instructions in #4.
Remove Rotating Mist Nozzle
prior to lling the Water Tank. Lift the Water Tank with both
hands using the Handle to
remove the humidier from
the Base.
Turn the Water Tank upside
down and remove the Tank Cap
by turning it counter clockwise.
12
4
3
Lift the Water Tank with both
hands using the Handle and
replace on the humidier Base.
Make sure to follow the shape
of the Water Tank and the hu-
midier Base, so that the tank
sits level and ush to the Base.
Ensure the tank is rmly seated.
5
Attach the Rotating Mist Nozzle
to the top of the Water Tank by
snapping into place for desired
use as pictured.
6
Filling the Water Tank:
Use clean, cool, tap water.
WARNING: DO NOT
use
extremely cold water, since it may
temporarily reduce the mist output.
WARNING:
NEVER ll with
hot/warm water or use additives
as this could damage the unit and
void the warranty.
WARNING:
If you have hard tap water STOP
using tap water and use ONLY
ltered, distilled, cold boiled or
bottled water.
Replace the Tank Cap by rmly
turning clockwise until tight.
Turn the Water Tank upright and
check the Tank Cap for leaks.
If any water drips, remove the
Tank Cap and retighten.
WARNING: DO NOT place
Water Tank on the humidier
Base if the cap is leaking.
7

Operating Instructions
WARNING: DO NOT operate the humidier without water in the tank.
WARNING: NEVER lift the tank o the Base while the unit is operating.
ON/OFF – Plug into a standard (120V AC) electrical outlet. The LED Display will turn
on for 2 seconds then turn OFF. Press the ON/OFF button once and the “Operating”
indicator will turn on. Mist may not appear immediately; allow up to 15 minutes for the
water in the tank to transfer to the Base.
Beep/Dim – The humidier automatically defaults to an audible beep when
changing settings, the waterless indicator will illuminate and you will hear three
beeps when the humidier is out of water and the LED Display will be illuminated.
To disable one or more of these settings, follow the steps below:
Press Beep/Dim once to disable all sound (Beep O will ash on the display three
times and then will remain on the display to indicate the sound is OFF). Press the
button twice to turn the LED Display OFF (sound will remain OFF) and Press a third
time to enable the LED Display and the sound (default function).
LOW Water – When the tank is out of water the “waterless” indicator will appear in
the display, you will hear three beeps and the automatic safety shut-o will turn the
Ultrasonic Nebulizer & unit OFF. Note: You can disable the audible beep by pressing the
Beep/Dim button once. To re-enable, press the Beep/Dim button two more times.
1
3
2
7
6
4
5
5
The Delay Start and Auto-O buttons allow you to set the humidier to turn ON and OFF automatically as desired.
Delay Start – The Delay Start feature allows you to program the unit to turn ON
Automatically. To use, press the “Delay Start” button once; you will see “Delay
Start” 01:00H illuminated on the display. This feature works in one hour
increments and is programmable up to 24 hours. Simply keep pressing the Delay
Start button until you get to your desired delay start time, once you have reached
the time the display will ash three times and then will start to countdown until
the unit turns ON.
Auto-O – The Auto-O feature allows you to run the humidier now and set it
to turn OFF at a specic time automatically (in 1 hour increments from 1-24 hours).
To use - press the “Auto-O’ button once; you will see “Auto-O” 01:00H illuminated
on the display. This feature works in one hour increments and is programmable up
to 24 hours. Simply keep pressing the Auto-O button until you get to your desired
Auto-O time, once you have reached the time the display will ash three times and
then start to count down until the unit turns OFF. The display will start alternating
between the current ambient humidity and the Auto-o Timer. NOTE: You can use
the Delay Start and Auto-O functions together on this fully programmable LED
Display to program the humidier to turn ON and turn OFF at your desired times.
Mist Output – When you turn the unit ON, it will default to the lowest mist setting. Pressing
the “Mist” button each time will increase the output. Press once for Medium, twice for High, three
times for Supreme. Pressing the Mist button a fourth time will bring the unit back to Low.
Humidistat – By using this feature the humidier will automatically monitor and
control the humidity level according to your desired setting. Once the desired humidity
level is reached the mist will shut OFF until the humidity drops below the setting and
then the mist will turn back ON automatically to maintain the humidity level desired. To
set this feature press the “Humidistat” button to your desired setting. Settings range
from 40%-95% RH (Relative Humidity) in 5% RH increments. A 40%-60% Relative
Humidity is recommended. Once you set your desired humidity, the number will blink
three times and then the display will revert back to the Relative Humidity. To view the
set humidity level, press the Humidistat button once.

Weekly Cleaning & Care
WARNING: Before cleaning always turn power o and unplug the unit from outlet.
WARNING: DO NOT rinse Base under faucet. To clean, wipe the Base with a paper towel.
WARNING: DO NOT use any solvents or aggressive cleaning agents. Keep water away
from the Air Outlet.
WARNING: DO NOT tamper with the Water Sensor.
About White Dust -Use of high-mineral content water may cause a white mineral residue to
accumulate on room surfaces near the humidier. The mineral residue is commonly referred to as
“White Dust”. The higher the mineral content (the harder your water is), the greater the potential for
White Dust. The White Dust is not caused by a defect in the humidier, but is due only to minerals
suspended in the water from your tap.
WARNING: If you have hard tap water STOP using tap
water and use ONLY ltered, distilled, cold boiled or bottled water to minimize the White Dust
residue.
Tank Cleaning - Remove the Rotating Mist Nozzle from the top of the Water Tank then remove the
Water Tank from the unit. Turn the tank upside down, unscrew the Tank Cap and drain any water
from the tank. Wipe the tank with a soft damp cloth then
rinse it with warm water inside and out.
Base Cleaning - Gently wipe the Base with a
soft damp cloth.
White Dust Cleaning - If mineral deposits
“White Dust” are evident around the Ultrasonic
Nebulizer and Water Sensor, clean these surfaces
with a soft cloth and a small amount of undiluted
white vinegar. If necessary, mix a solution of 50%
white vinegar and 50% water and ll the Base with
enough solution to cover the Ultrasonic Nebulizer (a).
Allow it to soak for an hour and then use the provided
brush to gently loosen buildup on the
Ultrasonic Nebulizer (b). Put 1 cup of water in the
Base and wipe clean with a soft cloth.
WARNING: DO NOT rinse Base under faucet.
Ceramic Water Filter Cleaning - Remove the
Water Tank from the humidier Base. Remove the
Tank Cap (c) and rinse Ceramic Filter thoroughly with
tap water (d), then replace on Water Tank.
Surface Cleaning - Clean all surfaces of the unit with a clean
damp soft cloth.
WARNING: When emptying the Water Reservoir on the Base, make
sure that the water is poured away from the Air Outlet (e). If water is
poured into the outlet it may damage the humidier.
Storage
1. Follow all cleaning instructions prior to storage.
2. Dry all parts, including the inside of the Water Tank.
WARNING: Never leave water inside the tank for several days.
3. Leave the Tank Cap partially loosened to prolong the life of the cap.
4. Preferably store in its original box, in a dry place away from high temperatures.
5. Follow all cleaning instructions after long periods of storage.
6
a
e
c
b
d

Troubleshooting
7
PROBLEM: Power Light is OFF
POSSIBLE CAUSES
a. Unit is not plugged in
b. No power at outlet
POSSIBLE SOLUTIONS
a. Plug in power cable
b. Check circuits, fuses, or try a dierent outlet
c. Press the ON/OFF button to turn
the power on
PROBLEM: Weak or No mist output
POSSIBLE CAUSES
a. No water in tank
b. Unit is not level
c. White Dust on Ultrasonic Nebulizer
and/or Water Sensor
d. Blower not operating
e. Water temperature is too low
f. Ultrasonic Nebulizer is not operating
POSSIBLE SOLUTIONS
a. Fill tank with water and wait 10 – 15 minutes
b. Place unit on level surface
c. Clean humidier per instructions
d. Ensure there is enough water in Base
to activate Water Sensor
e. Set output to High and wait for
10 – 15 minutes
f. See Warranty
PROBLEM: Peculiar Odor
POSSIBLE CAUSES
a. If new unit
b. Dirty Water Tank or old water in tank
c. Minerals in well water or hard water
POSSIBLE SOLUTIONS
a. Gently wipe the Base with a soft damp cloth
b. Empty old water and clean Water Tank per
instructions
c. Use ltered, distilled, cold boiled or bottled
water
PROBLEM: White Dust on unit or nearby
furniture
POSSIBLE CAUSE
a. Hard water used
POSSIBLE SOLUTION
a. Use ltered, distilled, cold boiled or bottled
water
PROBLEM: Condensation forms
around humidier or windows
POSSIBLE CAUSES
a. Mist output is set too high for the room size
b. Direction of Rotating Mist Nozzle
POSSIBLE SOLUTIONS
a. Decrease the mist output
b. Change direction of the Rotating Mist Nozzle
PROBLEM: Water is leaking
POSSIBLE CAUSES
a. Tank Cap is not properly attached
b. Water Tank is not properly seated
c. Unit is not on level surface
POSSIBLE SOLUTIONS
a. Follow #5 on page 4 “Filling the Water Tank”
b. Follow #6 on page 4 “Filling the Water Tank”
c. Place on level surface

8
Try These Other Great
Products For Your Life!
Available at: www.qvc.com & www.forlifeproducts.com
Try These Other Great
Products For Your Life!
Available at: www.qvc.com & www.forlifeproducts.com
Ultrasonic Humidiers Air Puriers

1-YEAR WARRANTY - MH-512
Air Innovations® Clean Mist™ Smart Humidier™ comes with a 1-year manufacturer’s
warranty. If this unit should become defective within 1-year from the date of purchase,
or if you have any questions or comments or regarding replacements for any of our
products, please contact us directly at:
Call us toll free at: 844-600-1370
Monday thru Friday 8:30 AM to 5:00 PM EST.
Visit us on the web at: www.GreatInnovations.tv
e-mail us: [email protected]
Or write us:
Great Innovations, LLC
Att: Quality Assurance Dept.
2301 SW 145th Ave.
Miramar, FL. 33027 USA
Please ll out the warranty card and
mail back to the above address.
Or, register your warranty online today.
Simply go to:
http://www.greatinnovations.tv/warranty.php
NAME
ADDRESS
CITY
STATE ZIP
TELEPHONE
E-MAIL
DATE OF PURCHASE
PLACE OF PURCHASE
THIS UNIT COMES WITH A 1-YEAR WARRANTY SUBJECT TO THE FOLLOWING CONDITIONS:
In the rst year, all repairs will be performed free of charge or the unit will be replaced. This
warranty is not transferable, it is valid only for the original purchaser. This warranty will be
voided if the unit is subjected to unauthorized repair or impact damage. If you have any
questions please call toll free: 844-600-1370
Please check here if you would not like to receive any solicitations from our company
9
!

Air Innovations® ©2015 Great Innovations, LLC. All Rights Reserved. US & International Patents Pending.
Available In A Variety Of Colors