AIRINNOVATIONS CLEAN MIST TOP-FILL SENSA TOUCH Instruction Manual

READ AND SAVE THESE INSTRUCTIONS
nished size 5.5” wide x 8.5” high
CLEAN MIST® TOP-FILL SENSA TOUCH™
BLUETOOTH HUMIDIFIER WITH
CRISP SOUND™ BLUETOOTH SPEAKER & AROMA TRAY
Instruction Manual and Warranty Information
Bluetooth Enabled
Use your smart device to
monitor humidity levels and
adjust settings With Built-In
Crisp Sound™
Bluetooth Speaker

Contents
Safety Instructions ............................................................................................................. 1
Unpacking / Specications ............................................................................................... 2
Parts & Contents ............................................................................................................... 3
Filling The Water Tank ....................................................................................................... 4
Operating Instructions ....................................................................................................... 5
Weekly Cleaning & Care / Storage .................................................................................... 6
Troubleshooting ................................................................................................................. 7
Other Great Products ........................................................................................................ 8
Warranty ............................................................................................................................ 9
If you have a respiratory condition, please contact your physician prior to use.
FCC Statement
Potential for Radio/Television interference
WARNING: Changes or modications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment. A recommended separation distance of 20 cm from the radiating
element should be maintained.
Note: This device complies with Part 15 and 18 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to part 15 and Part 18 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

1
SAFETY INSTRUCTIONS
• This appliance has a polarized plug (one blade is wider than the other) as a safety
feature. If the plug does not t fully into the outlet, reverse the plug. If it still doesn’t
t, contact a qualied electrician. DO NOT attempt to defeat this safety feature.
• Before using the humidier, extend the cord and inspect for any signs of damage; DO
NOT use if the cord has been damaged.
• Keep cord away from heated surfaces and out of the way, where it cannot be
stepped on or tripped over.
• NEVER use in an environment where explosive gases are present.
• Place humidier on a stable level surface; DO NOT place on carpet, next to
heating vents, under direct sunlight, in high temperature areas, or near computers
and electronic equipment.
• DO NOT place the the humidier directly on wood furniture or other surfaces which
could get damaged by water.
• DO NOT direct the mist against a wall or home appliances.
• NEVER operate without water in the Tank; DO NOT use anything other than room
temperature tap or distilled water.
• NEVER add essential oils directly to the water, as this will damage the unit and void
the warranty.
• DO NOT touch the water in the Base during operation.
• DO NOT expose or immerse the Base in water when cleaning.
• DO NOT pour water into the base through the Air Outlet during cleaning and lling.
• NEVER block the Air Outlet or intake or cover the unit when it’s in operation
• DO NOT use any attachments not provided with the unit.
• Discontinue use if humidier makes loud noises or has a strange smell.
• DO NOT attempt to repair or adjust the unit; servicing must be performed by
professional or qualied personnel.
• Only operate when fully assembled; only use as intended and described in this manual.
• Keep out of reach of small children.
• Always insert plug securely into the power source.
• Unplug the unit and empty the Water Tank and Base before carrying/moving.
• Only unplug when the humidier is turned o; ensure hands are dry.
• Always turn o the unit before removing, emptying or lling the Water Tank.
• Perform regular maintenance of the Ultrasonic Nebulizer; NEVER scrape Nebulizer with
a hard or sharp object.
• Dry the unit completely before storage; store in a cool, dry place.
• Do not drop, hit or otherwise subject this product to excessive shock.
READ AND SAVE THESE INSTRUCTIONS: Falure to follow
all the instructions may result in electrical shock.
WARNING
CAUTION

No More Dry Air
Thank you for choosing the Air Innovations® – Clean Mist® Top-Fill Sensa Touch™
Bluetooth Humidier with Bluetooth Speaker & Aroma Tray and congratulations on taking
this important step in improving the quality of air in your home or oce. The humidier
uses Ultrasonic Technology to create humidity instantaneously - working silently to erase
the discomforts of dry air.
Unpacking
Specications
*Follow directions to ll and operate the humidier.
2
1
3Remove the plastic bag from the humidier.
Remove the Dual Directional Mist Nozzle.
2Carefully remove the Extension
Nozzle and humidier from the
box by pulling the Base of the
unit (Do not take the unit out of
the box by pulling the tank).
MH-906 6.1L / 1.6G 10.5”W x 7.75”D
x 34”H
4.47 Lbs.

1. Dual Directional Mist Nozzle
2. Extension Nozzle
3. 3a. Water Tank Lid / 3b. Finger Lift
4. Water Tank
5. Base with Built-In
Crisp Sound™Bluetooth Speaker
6. Sensa Touch™ Control Panel
7. Air Outlet
8. Cleaning Brush
9. Water Reservoir
10. Ultrasonic Nebulizer
11. Water Sensors
12. Water Inlet
13. Ceramic Filter
14. Silicone Plug (to be used during cleaning ONLY)
15. Aroma Tray (located on the rear of the unit)
3
Parts & Contents
7
8
9
10
11
12
Tank Top View
Base Top View
3b
13
14
1
2
4
5
6
3a
15

Ensure the Water Tank is rmly seated on the
Base so there is no visible gap between Water
Tank and Base.
Use the Finger Lift to open the Water Tank Lid.
12
Filling The Water Tank
WARNING: Never turn Water Tank upside down when full.
WARNING: DO NOT use extremely cold water, since it may temporarily reduce the mist output.
WARNING: NEVER ll with hot/warm water or use additives as this could damage the unit and
void the warranty.
WARNING: If you have hard water use our Humidier Demineralization Filters (available at www.
Air-Innovations.com) or use ONLY ltered/distilled water.
Fill the Water Tank using clean, cool water.
Note: Do not ll past the MAX ll line.
4
3
Close the Water Tank Lid.
NOTE: DO NOT
block air holes as this will eect the performance of
the unit.
4
Close the Water Tank Lid.
5
Attach the Dual Directional Mist Nozzle to the top of the Water Tank. To easily control the direction of
the mist simply separate the Dual Directional Mist Nozzle and position as desired-see photo above.
Extension Nozzle – To convert this unit from a Tabletop unit to Floor unit simply remove the Dual
Directional Mist Nozzle from the top of the Water Tank. Position the unit on a at, level surface and
insert the Extension Nozzle into the top of the Water Tank. Place the Mist Nozzle on top of the
Extension Nozzle.

55
Operating Instructions
Plug unit into a standard (120V AC) electrical outlet.
ON/OFF - Touch the Sensa Touch™ power button to turn the humidier on. NOTE: During the rst use
the waterless indicator may illuminate before mist appears; allow up to 15 minutes for the water in the
tank to transfer to the base.
Mist Output - When you turn the unit ON, it will default to the Low mist setting and one white LED light
will be lit. Touching the power button again will increase the output, and is indicated by the additional
white LED lights (see below). Touch once for Medium, twice for High, three times for the Supreme
setting. Touching the power button a fourth time will turn the humidier o.
Auto LED Dim: After approximately 30 seconds, the LED light will automatically turn o. Touching the
power button on the unit will illuminate the light again but will not change the setting. Touch the power
button a second time to alter the setting. The humidier is factory set to silent mode and will only beep to
indicate the unit is out of water.
Auto Safety Shut-O - When the Tank is out of water the Waterless indicator
will illuminate and the automatic safety shut-o will turn the unit OFF. The unit
will beep three times before turning o.
Aroma Tray- By inserting an Air Innovations Aroma Pad into the built-in
Aroma Tray, you can transform your humidier into an easy-to-use fragrance
dispenser. Visit www.Air-Innovations.com to purchase additional Aroma Pads.
Bluetooth Operation Instructions
Bluetooth Enabled Control – The humidier can be turned On/O and mist settings can be
adjusted from any smart device.
Crisp Sound™ Bluetooth Speaker – Our humidier has a built-in speaker which is compatible
with all Bluetooth audio devices. The speaker can be enjoyed with the humidier turned On or O.
1. To use the Bluetooth Function rst download the App from the App Store / Google Play Store,
see below. Look for "Air Innovations Technology"
A. iOS / Apple App Store
B. Android / Google Play Store
2. Open the App & Press the Red Bluetooth Icon labeled “Press To Connect”.
Note: To disconnect humidier “AI-906 Device” toggle OFF your Bluetooth in your
phone settings. To disconnect from Speaker “AI – 906 Spkr” choose to “forget” or
“unpair” from your phone settings.
AROMA
TRAY
LOW MEDIUM HIGH SUPREME
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries and regions. App Store is a service mark of Apple Inc.
Google Play and the Google Play logo are trademarks of Google LLC.

a
b
d
e
Weekly Cleaning & Care
WARNING: Before cleaning always turn power o and unplug the unit from outlet.
WARNING: DO NOT rinse Base under faucet. To clean, wipe the Base with a soft cloth.
WARNING: DO NOT use any solvents or aggressive cleaning agents. Keep water away from the Air Outlet.
WARNING: DO NOT tamper with the Water Sensor.
About White Dust -Use of high-mineral content water may cause a white mineral residue to accumulate on room surfaces
near the humidier. The mineral residue is commonly referred to as “White Dust”. The higher the mineral content (the harder
your water), the greater the potential for White Dust. The White Dust is not caused by a defect in the humidier, but is due only
to minerals suspended in the water from your tap.
WARNING: If you have hard tap water STOP using tap water and visit our
website (www.Air-Innovations.com) to purchase our Humidier Demineralization Filters or use ONLY ltered or distilled water.
Tank Cleaning - Unplug unit & remove the Mist Nozzle from the top of the Water Tank then remove the Water Tank from the
unit. Turn the tank upside down and drain any water from the tank. Wipe the tank with a soft damp cloth then rinse it with
warm water inside and out.
Base Cleaning
1. Unplug unit.
2. Use enclosed Silicone Plug and place over water inlet (see below).
3. Clean the Base by gently wiping with a soft damp cloth.
White Dust Cleaning - If mineral deposits are evident around the
Ultrasonic Nebulizer
a
and Water Sensor, clean these surfaces
with a soft cloth and a small amount of undiluted white vinegar.
If necessary, mix a solution of 50% white vinegar and 50% water
and ll the Base with enough solution to cover the Ultrasonic
Nebulizer
a
. Allow it to soak for an hour and then use the provided
brush to gently loosen buildup on the Ultrasonic Nebulizer
b
.
Put 1 cup of water in the Base and wipe clean with a soft cloth.
WARNING: DO NOT rinse Base under faucet.
WARNING: When emptying the Water Reservoir in the Base,
make sure that the water is poured away from the Air Outlet
c
.
If water is poured into the outlet it may damage the humidier.
Ceramic Water Filter Cleaning
1. Unplug unit and empty water from Tank.
2. Lift Water Tank Lid and place hand inside the Tank and moderately grasp
the Ceramic Water Filter and unscrew by twisting counterclockwise
d
.
Rinse the Ceramic Filter with running tap water for approx 20-30 seconds
e
.
Then replace lter inside Water Tank by twisting clockwise until secure
f
.
Surface Cleaning - Clean all surfaces of the unit with a clean damp soft cloth.
6
1. Follow all cleaning instructions prior to storage.
2. Dry all parts, including the inside of the Water Tank.
3. Preferably store in its original box, in a dry place away from high temperatures.
4. Follow all cleaning instructions after long periods of storage.
Storage
cf
Using Silicone Plug
Please apply the enclosed plug during cleaning ONLY in order to avoid
debris from entering the pump. NOTE: the plug MUST be REMOVED
for normal operation and lling.

Troubleshooting
7
Problem Solution
My device will not connect
to the humidier.
Bluetooth is not on: On your smartphone go to Settings and
turn Bluetooth on, then follow the instructions on the
Bluetooth section.
The smartphone is out of range: Move the smartphone closer
to the humidier - depending on your surroundings, your
device will stay connected up to 75 feet.
A dierent device is connected: Disconnect the device and
re-connect with another.
Weak or no mist output. The water in the unit is too cold: Replace with cool but not
cold water or set output to High and wait 10-15 minutes.
The surface of the Ultrasonic Nebulizer is dirty: Clean
Ultrasonic Nebulizer. (see pg. 6 “White Dust Cleaning”)
Ultrasonic Nebulizer is not working: See Warranty.
Air Holes in Lid are blocked: Do not cover or block air holes.
White dust is forming on
nearby furniture.
Hard tap water may deposit a certain amount of dust. Visit our
website (www.Air-Innovations.com) to purchase Humidier
Demineralization Filters or use distilled water.
Water is leaking. Water Tank Installation: Make sure the tank is correctly
attached. (see pg. 4 “Filling the Water Tank”)
Humidier is not on a level surface: Place on level surface.
Condensation is forming
around humidier or
windows.
Mist output level is too high for room size: Decrease the mist
output.
Direction of Rotating Mist Nozzle: Change direction of nozzle.
4 LED lights continuously
ash for more than one
minute.
Unit is in Alert Mode: Unplug and restart the humidier;
if problem continues, call our Customer Service Center for
assistance.
Missing parts. Call us toll free at: 844-600-1370, Monday thru Friday
8:30am to 5pm EST.
Please reference model: MH-906

Try These Other Great
Products For Your Life!
Available at: www.ForLifeProducts.com, www.Air-Innovations.com, www.Pursfection.com, www.RejuvenateProducts.com
8

1-YEAR WARRANTY - MH-906
Air Innovations® Clean Mist™ Top-Fill Sensa Touch™ Bluetooth Humidier with Crisp
Sound™ Bluetooth Speaker & Aroma Tray comes with a 1-year manufacturer’s warran-
ty. If this unit should become defective within 1-year from the date of purchase, or if you
have any questions or comments or regarding replacements for any of our products,
please contact us directly at:
Call us toll free at: 844-600-1370
Monday thru Friday 8:30 AM to 5:00 PM EST.
Visit us on the web at: www.Air-Innovations.com
e-mail us: [e-mail]
Or write us:
Great Innovations, LLC
Att: Quality Assurance Dept.
2301 SW 145th Ave.
Miramar, FL. 33027 USA
Please ll out the warranty card and
mail back to the above address.
Or, register your warranty online today.
Simply go to:
www.Air-Innovations.com
NAME
ADDRESS
CITY
STATE ZIP
TELEPHONE
E-MAIL
DATE OF PURCHASE
PLACE OF PURCHASE
THIS UNIT COMES WITH A 1-YEAR WARRANTY SUBJECT TO THE FOLLOWING CONDITIONS:
In the rst year, all repairs will be performed free of charge or the unit will be replaced. This warranty
is not transferable, it is valid only for the original purchaser. This warranty will be voided if the unit is
subjected to unauthorized repair or impact damage. If you have any questions please call toll free:
844-600-1370. This warranty gives you specic legal rights, and you may also have other rights
which vary from state to state.
Please check here if you would not like to receive any solicitations from our company
!
9

Air Innovations® ©2019 Great Innovations, LLC. All Rights Reserved. US & International Patents Pending. Printed in China.
Available In A Variety Of Colors
With Built-In
Crisp Sound™
Bluetooth Speaker