AIRINNOVATIONS CLEAN MIST Instruction Manual

CLEAN MIST™ULTRASONIC
PERSONAL HUMIDIFIER WITH UV LIGHT
Instruction Manual and Warranty Information
IM0040A READ AND SAVE THESE INSTRUCTIONS

Contents
Safety Instructions 1
Assembly Instructions / Specications 2
Parts & Contents 3
Attaching The Water Bottle 4
Operating Instructions / Storage / About White Dust 5
Weekly Cleaning & Care 6
Troubleshooting 7
Other Great Products 8
Warranty 9
If you have a respiratory condition, please contact your physician prior to use.
FCC Statement
Potential for Radio/Television interference
This device complies with Part 18 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.This product has been tested and
found to comply with the limits for a Class B digital device, pursuant to Part 18 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. The product generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur in a particular installation. If the product
does cause harmful interference to radio or television reception, which can be determined by turning the
product on or o, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the receiver.
• Connect the product into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
• Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.

SAFETY INSTRUCTIONS
1
Prior to using the appliance, read through the instructions for complete use and keep in a
safe place for later reference.
• WARNING: DO NOT use outdoors. Only use as intended and described in this manual.
• WARNING: DO NOT expose or immerse the Base in water or other liquids.
• Before using the appliance, extend the cord and inspect for any signs of damage.
WARNING: DO NOT use if Power Adaptor has been damaged.
• WARNING: Keep cord away from heated surfaces and out of the way, where it cannot be
stepped on or tripped over.
• WARNING: ALWAYS place humidier on an elevated rm, at, level surface where it’s not
easily knocked over. (e.g. on a table, chest, cabinet, etc).
• WARNING: DO NOT place the appliance directly on the oor, next to a heating vent, under
direct sunlight, high temperature areas, near computers or sensitive electronic equipment.
• WARNING: DO NOT place the appliance directly on wood furniture or other surfaces which
could get damaged by water.
• WARNING: NEVER use in an environment where explosive gases are present.
• WARNING: DO NOT use any attachments not provided with the unit.
• WARNING: NEVER use the appliance after a malfunction, after it has been dropped or
damaged in any other way.
• Only operate when fully assembled.
• Keep out of reach of children. Close supervision is necessary when this appliance is used by or
near children, elderly or disabled persons.
• WARNING: NEVER drop or insert any object into any opening.
• WARNING: DO NOT block any air outlets or intakes.
• WARNING: NEVER cover the appliance when it’s in operation.
• WARNING: To unplug turn humidier OFF, then remove the Power Adaptor from the outlet.
Ensure your hands are dry.
• WARNING: ALWAYS unplug the Power Adaptor by holding the adaptor itself.
WARNING: NEVER pull on the cord itself to unplug from the power outlet.
• WARNING: ALWAYS unplug and EMPTY the water bottle when not in use for a long period
of time.
• WARNING: ALWAYS turn OFF or unplug before removing, lling or emptying the
water bottle.
• WARNING: DO NOT wash, adjust or move without rst unplugging the unit.
• WARNING: DO NOT touch the water or any other part in the Base during operation.
• WARNING: NEVER operate WITHOUT water in the water bottle.
• WARNING: DO NOT use hot water in the unit.
• WARNING: ONLY use water in the water bottle, never use any additive such as essential
oils, eucalyptus, water conditioners, etc… in the water.
• WARNING: DO NOT move appliance with water inside the unit. In this case remove the
water bottle and empty the water bottle prior to moving.
• WARNING: DO NOT attempt to repair or adjust the unit. Servicing must be performed by
professional or qualied personnel.
• WARNING: Discontinue use if unit makes loud noises or has a strange smell.
• Perform regular maintenance of the Ultrasonic Nebulizer.
• WARNING: DO NOT direct the mist against a wall or other home appliance.
• WARNING: DO NOT pour water into the Base through Air Outlet during cleaning and lling.
• WARNING: DO NOT rinse Base under faucet.
• WARNING: DO NOT immerse the Base in water.
• WARNING: NEVER scrape the Ultrasonic Nebulizer with a hard or sharp object.

No More Dry Air
Thank you for choosing the Air Innovations®Clean Mist™ Ultrasonic Personal Humidier with
UV Light and congratulations on taking this important step in improving the quality of air in your
home, oce, hotel or anywhere you go.
Air Innovations®Clean Mist™ Ultrasonic Personal Humidier with UV Light uses Ultrasonic
Technology to create humidity instantaneously, while working silently to erase the discomforts
of dry air. The Universal Water Bottle Adaptor will t most water bottles.
Assembly Instructions
1. Carefully remove all contents from the box.
2. Slide out the two Bottom Supports on the bottom of the Base. This will help prevent the unit from tipping over.
3. Make sure the Top Cover is securely installed to the Base of the unit.
4. Prior to use, lift Mist Outlet to the open position.
5. Attach the Power Adaptor to the rear of the Base, then plug into a standard (110V) outlet.
6. Follow Operating Instructions.
Specications
4 5
2
3
Product Model
MH-105 8W-11W 16.9  oz. 0.7 lbs.
100-240V~50/60Hz L 4.25” X W 2.625”
X H 3.17”
Power Consumption Rating Voltage Suggested Water Bottle Dimensions Weight
2

Parts & Contents
3
2
13 4 5 78
10 12 13
14
11
6
1. Air Outlet
2. Water Reservoir
3. Ultrasonic Nebulizer
4. Water Sensor
5. LED UV Light
6. Mist Outlet
7. Water Bottle Adaptor Opening
8. Power Adaptor
9. Carry Bag
10. Base
11. Supports
12. Power/Mist Control Button
13. Power Adaptor Port
14. Universal Water Bottle Adaptor
9

4
Attaching The Water Bottle
WARNING: Always unplug the unit before removing the water bottle.
WARNING: DO NOT touch the water in the Water Reservoir.
1. Using any standard 16.9-32  oz. water bottle (not provided) or if desired ll an empty water
bottle with clean, cool, tap water.
WARNING: 32oz. bottle may be top heavy and cause
the unit to tip over if the Bottom Supports are not pulled out. WARNING: DO NOT use
extremely cold water, since it may temporarily reduce the Mist Output. WARNING: NEVER
ll with hot/warm water or use additives as this could damage the unit and void the warranty.
WARNING: If you have hard tap water STOP using tap water and use ONLY ltered,
distilled, cold boiled or bottled water.
2. Remove the cap OFF the bottle and place bottle on a at surface.
3. Hold the bottle by the neck and start inserting the Universal Water Bottle Adaptor at an
angle. Note: there are 2 dierent positions on the Universal Water Bottle Adaptor to t most
water bottles. (See #3 Below)
4. Once the rst threads are inside the bottle press the Water Bottle Adaptor straight down until
it touches the bottle seal. (See #4 Below)
5. Turn the Water Bottle Adaptor upside down and check the adaptor for leaks. If any
water drips from the outside edge, remove the adaptor and reinsert. WARNING: DO NOT
place the water bottle on the humidier if the adaptor is leaking. (See #5 Below)
NOTE: Do not place the water bottle on the humidier if water is leaking from the
sides of the adaptor. However, a small drip from underneath the adaptor is normal.
6. When placing the Water Bottle Adaptor on the unit, make sure the Water Bottle Adaptor
notch is in the correct position and the bottle sits level and ush to the Top Cover.
(See #6 Below)
3
5 6
4

Operating Instructions
WARNING: DO NOT operate the humidier without water in the water bottle.
WARNING: NEVER lift the water bottle OFF the Base while the unit is operating.
NOTE: Do not operate the humidier without a full water bottle attached.
1. ON/OFF/Mist Output - Plug into a standard (110V) electrical outlet with the supplied
Power Adaptor. Press the Power Button once to turn ON. Mist output will be on HIGH;
press the Power Button a second time to change the mist output to LOW. To turn OFF,
press the Power Button a third time. Mist may not appear immediately; allow up to 15
minutes for the water in the water bottle to transfer to the Base.
2. UV Light – The UV Light function automatically comes on when the unit is turned ON.
To deactivate, depress the Power Button for 3 - 5 seconds.
3. Low Water – When the Water Reservoir is out of water the automatic safety shut-o will
turn the Ultrasonic Nebulizer OFF. You may hear the fan for a few seconds, this is normal.
Storage
1. Follow all cleaning instructions prior to storage.
2. Dry all parts, including the inside of the Base.
WARNING: NEVER
leave water inside
the Base for several days.
3. To prolong the life of the Water Bottle Adaptor, do not store inside of a water bottle.
4. Preferably store in its original box, in a dry place away from high temperatures.
5. Follow all cleaning instructions after long periods of storage.
5
About White Dust
Use of high-mineral content water may cause a white mineral residue to accumulate on room
surfaces near the humidier. The mineral residue is commonly referred to as “White Dust”. The
higher the mineral content (the harder your water is), the greater the potential for White Dust.
The White Dust is not caused by a defect in the humidier, but is due only to minerals
suspended in the water from your tap.
WARNING:
If you have hard tap water STOP using
tap water and use ONLY ltered, distilled, cold boiled or bottled water to minimize the White
Dust residue.

Weekly Cleaning & Care
WARNING: Before cleaning always turn power OFF and unplug the unit from outlet.
WARNING: DO NOT rinse Base under faucet. To clean, wipe the Base with a soft cloth.
WARNING: DO NOT use any solvents or aggressive cleaning agents. Keep water away from
the Air Outlet. WARNING: DO NOT tamper with the Water Sensor.
NOTE: Recommended to change the water bottle frequently.
Emptying the Base
Remove the water bottle and Top Cover from the Base. Pour the water in the Water
Reservior away from the Air Outlet (a). This will help prevent water from pouring into the
Air Outlet which can cause the unit to malfunction.
Base & Surface Cleaning
Gently wipe with a soft damp cloth (b). WARNING: NEVER scrape the Ultrasonic
Nebulizer with a hard or sharp object.
White Dust Cleaning
If mineral deposits “White Dust” are evident around the Ultrasonic Nebulizer and Water
Sensor, clean these surfaces with a soft cloth and a small amount of undiluted white
vinegar. If necessary, mix a solution of 50% white vinegar and 50% water and ll the Base
with enough solution to cover the Ultrasonic Nebulizer. Allow it to soak for an hour and then
use a cotton swab to gently loosen buildup on the Ultrasonic Nebulizer (c). Put water in the
Base and wipe clean with a soft cloth. WARNING: DO NOT rinse Base under faucet.
Bottle Adaptor Cleaning
Remove the Water Bottle Adaptor from the bottle and rinse thoroughly with tap water (d),
then replace on bottle.
6
ab c d

Troubleshooting
PROBLEM: Weak or No mist output
POSSIBLE CAUSES
a. No water in Water Reservoir
b. Unit is not level
c. White Dust on Ultrasonic Nebulizer and/or
Water Sensor
d. Blower not operating
e. Water temperature too low
f. Wrong Power Adaptor
g. Ultrasonic Nebulizer not operating
h. Base has too much water inside
POSSIBLE SOLUTIONS
a. Place water bottle on and wait up to 10 minutes
b. Place unit on level surface
c. Clean humidier per instructions
d. Ensure there is enough water in the Base to
activate the Water Sensor
e. Set output to High and wait for
10 – 15 minutes
f. Use only DC18V Power Adaptor (included)
g. See Warranty
h. Turn OFF the unit, unplug and pour out the water
in the Base, then rell
PROBLEM: Peculiar Odor
POSSIBLE CAUSES
a. If new unit
b. Dirty water bottle or old water in unit
c. Old bottle
d. Minerals in well water or hard water
POSSIBLE SOLUTIONS
a. Gently wipe the Base with a soft damp cloth
b. Empty old water and clean Water Reservoir
per instructions
c. Change to new water bottle
d. Use ltered, distilled, cold boiled or bottled water
PROBLEM : White Dust on unit or nearby furniture
POSSIBLE CAUSE
a. Hard water used
POSSIBLE SOLUTION
a. Use ltered, distilled, cold boiled or bottled water
PROBLEM: Condensation forms around humidier
POSSIBLE CAUSES
a. Mist output is set too high
POSSIBLE SOLUTIONS
a. Decrease mist output
PROBLEM: Water is leaking
POSSIBLE CAUSES
a. Water Bottle Adaptor is not properly attached or
water bottle not properly attached
b. Unit is not on level surface
POSSIBLE SOLUTIONS
a. Follow #3 on page 4 “Attaching The Water Bottle”
b. Place on level surface
7

Try These Other Great
Products For Your Life!
Available at: www.qvc.com & www.forlifeproducts.com
8
Ultrasonic Humidiers Air Puriers

1-YEAR WARRANTY - MH-105
Air Innovations® Clean Mist™ Ultrasonic Personal Humidier comes with a 1-year manufacturer’s
warranty. If this unit should become defective within 1-year from the date of purchase, or if you
have any questions or comments or regarding replacements for any of our products, please contact
us directly at:
Call us toll free at: 844-600-1370
Monday thru Friday 8:30 AM to 5:00 PM EST.
Visit us on the web at: www.GreatInnovations.tv
e-mail us: [e-mail]
Or write us:
Great Innovations, LLC
Att: Quality Assurance Dept.
2301 SW 145th Ave.
Miramar, FL. 33027 USA
Please ll out the warranty card and
mail back to the above address.
Or, register your warranty online today.
Simply go to: http://www.greatinnovations.tv/warranty.php
THIS UNIT COMES WITH A 1-YEAR WARRANTY SUBJECT TO THE FOLLOWING CONDITIONS:
In the rst year, all repairs will be performed free of charge or the unit will be replaced. This warranty is not
transferable, it is valid only for the original purchaser. This warranty will be voided if the unit is subjected to
unauthorized repair or impact damage. If you have any questions please call toll free: 844-600-1370.
This warranty gives you specic legal rights, and you may also have other rights which vary from state to state.
Please check here if you would not like to receive any solicitations from our company
NAME
ADDRESS
CITY
STATE ZIP
TELEPHONE
E-MAIL
DATE OF PURCHASE
PLACE OF PURCHASE
!

Available In A Variety Of Colors
Air Innovations® © Great Innovations, LLC 2015. All Rights Reserved. US & International Patents Pending. Made In China.