Airlink101 AICAP650W User manual

Ver. 1.0
Quick Installation Guide
Model # AICAP650W
SkyIPCam650W

Section 1
GettingStarted
System Requirement: Beforeyoubegin,pleasereviewthefollowingsystemrequirement.
• OS: Windows® 98SE/ME/2000/XP.
•CPU: 650MHzor above (2.4GHzrecommended when monitoringmultiplecameras simultaneously)
• Memory Size: 256MB
• Resolution: 1024x768 or above
• Web Browser: Internet Explorer 5.0 or above
This Quick Installation Guide only provides the basic instructions. For more
detailed information, please refer to the User’s Manual in the supplied CD.
Caution: The IP Camera is designed for indoor use only. Direct exposure to sunlight
may cause permanent damage to the CMOS sensor. When operating in extremely
bright environment, an iris lens or sun visor is recommended to protect the IP Camera.
Step 1 Align the camerastandwith the bottom partofthe camera.Then, secure thecamerastandwith
thescrew.

Step 3 Power on the IP Camera by connecting one end of the supplied power adapter to the power jack
ofthe Camera andconnectingthe other endtoan electrical outlet.
Step 4 Verifythat the LED lightsonthe Camera are lit.Ifnot,verify that alltheconnectionsare secure
andtry again.
Step 2 Connect one end of a networkcabletothe IP Camera and connect the other endtooneof the
LAN portsof the wireless router.

Section 2
Installing the Setup Wizard
Step 1Insertthe provided CD andwaitforthe autorun screen to appear.
Step 2 Click on Install Setup Wizard.
Note: If the autorun screen does not appear automatically, go to Start > Run > and type
D:\Setup\Setup.exe (where Dis the letter of your CD drive) and click OK.
Step 3 Click Next.

Step 4 Click Yes to accept the LicenseAgreement.
Step 5 Click Next to accept the default Destination Folder.
Step 6 Click Finish to complete the installation.

Section 3
Using the Setup Wizard
Step 1 Go to Start > (All) Programs >AirLink101 IP Camera Setup Wizard >AirLink101 IP Camera
Setup Wizard.
Step 2 Select theIPCamera youwant toconfigurefromthe listand clickon the Wizard button.

Step 3 IftheCamera’sdefaultIP address is on a differentsubnet, the following messagewillappear.
ClickYes to continue.If youdo notreceive thismessage, skipto Step 6.
Step 5 TheWizardwill automatically generate an IP address for thecamera,ifthis address is not in use
byany other deviceinyour local network,click OK. Otherwise,enteran available IPaddress(ex.
192.168.x.240)and click OK.
Step 4 Enter admin for both theAdmin ID and Password and click OK.

Step 6 Enteradmin forboththeAdmin ID andPassword fieldandclickNext.Optionally,you can
changethe password by checking on the Changeboxandenteringthe new password.
Step 7 If you need tochangetheCamera’s IP address because another networkdeviceisalready using
the same address, you can assign a new address here and click Next.
Step 8 Enter the SSID ofyourwireless router in the SSID fieldandclick Next.If you have encryption
enabled foryour wireless network,follow the subsequentsteps, otherwiseskip to Step 10.

WEP
WPA
Step 9a Select the appropriate Key Format and enter the same WEP Code Key as your wireless
router. Click Next and skip to Step 10.
Step 9bEnter the same WPAShare Key as your wireless router and click Next.
Step 10 Verify that all the fields are correctand click Restart to save the settings and reboot the camera.

Section 4
ViewingImages
Step 1 At theSetup Wizard,select thedesired camerafrom thelist andclick onthe Web Config button.
Step 2 Enter the password for the camera (Default is admin) and click OK.
Note: The following steps describe how to view images from within the same local area network as the
IPCamera. To view images from an external network such as the Internet, please refer to the User’s
Manual on the provided CD for further instructions.

Note: ActiveX must be installed and enabled on your Web Browser (Internet Explorer)
before you can view the live videos. For more information, please refer to the next section.
Step 3 The welcome page appears.Ifyou did not change the defaultpassword,you will be prompted to
do so before accessing the camera.
Step 4 TheMainmenu along with the live videoappearsonscreen.TheIPcamerais ready for use now.

Section 5
Enabling and InstallingActiveX
If no image appears on the web browser (Internet Explorer), follow the steps below to enable and install
ActiveX.
Step 1 OpenInternetExplorerand go to Tools > Internet Options.
Step 2 Select the Security tab and click on Custom Level.

Step 3 Verifythe following settings are selected.Click OK whendone:
• AutomaticpromptingforActiveXcontrols:Enable
• Download signedActiveX controls: Prompt
• RunActiveXcontrols andplug-ins: Enable
Step 4 CloseInternetExplorer and re-launchtheWeb Config screen.

Step 5 Click on the ActiveX Control prompt.
Step 6 Select InstallActiveX Control.
Step 7 Click on Install toinstalltheActiveXControl.
Step 8 AftertheActiveXControl isinstalledyoushould see thelivevideo on InternetExplorer.

Section 6
Wireless Connection
Afteryou haveconfiguredthe IPCamerafrom theSetupWizard, youmayunplug theCamera’snetwork
cablefrom the wireless router and place the cameraatthedesired location.
To accessthecamera from awireless computer,openthe webbrowser(Internet Explorer), entertheIP
Addressofthecamera(defaultis 192.168.1.240) and press Enter.

E-mail:[email protected]
Toll Free: 1-888-746-3238
WebSite:www.airlink101.com
Section 7
TechnicalSupport

*Theoretical maximum wireless signal rate based on IEEE standard 802.11g specifications. Actual data throughput will vary. Network conditions and
environmental factors, including volume of network traffic, building materials and construction, mix of wireless products used, radio frequency
interference (e.g., cordless telephones and microwaves) as well as network overhead lower actual data throughput rate. Specifications are subject
to change without notice. All products and trademarks are the property of their respective owners. Copyright ©2006 AirLink101™