AirLive WLAN-64GM User manual

Ver. 1.0
QIG
WLAN-64GM
Enterprise Wireless Controller & Gateway
WLAN-128GM
Enterprise Wireless Controller & Gateway

-1-
Chapter 2. Hardware Installation
2.1 WLAN-64GM and WLAN-128GM Port description.
LED Status Function
PWR
On
( Green )Wireless Controller is powered on
Off
System is off
Run
Blinking (Green)
Wireless Controller is working
Off
No traffic
WAN/LAN
Blinking
Cable connected and Data Transfer
LED Description.
Port Description.
Port Description
12V DC
12V
DC port for WLAN-64GM only
WAN
WAN
port connecting to Modem or Router
LAN 1~4
LAN
port connecting to the network equipment.
Reset
To
restore to the factory default setting, press and hold the Reset Button for
about 1
0 seconds, and then release it.
WLAN-64GM
QIG for WLAN-64GM, WLAN-128GM
WLAN-128GM
1.1
Package Contents ofWDAP-C7210E
Chapter 1. Product Introduction
PackageContents WLAN-64GM and WLAN-128GM
Before using this Wireless Controller, please check if there is anything missing in the package, and contact your dealer
of purchase to claim for missing items:
⚫WLAN-64GM or WLAN-128GM Wireless Controller
⚫Power Adapter (WLAN-6GM)
⚫Power Cable (WLAN-128GM)
⚫Mounting Ears
⚫InstallationGuide

-2-
2.2 WLAN-64GM, WLAN-128GM Hardware installation.
Connect the Wireless Controller via the WAN port to an Internet connection via a Modem or Router.
To control the Access Points connect them direct to the LAN ports of the controller via a (PoE) Switch.
The AirLive TOP-12AC, TOP-18AX and inWall-U618 as well as several outdoor CPE models are support by the Wireless
controller.
QIG for WLAN-64GM, WLAN-128GM

This chapter will show you how to configure the basic functions of your Wireless Controller within minutes.
-3-
Chapter 3. Quick Installation Guide
3.1 WLAN-64GM, WLAN-128GM , Web login Management.
TCP/IP Configuration.
The default IP address of the Wireless Controller is 192.168.10.1. By default, the Wireless Controller has DHCP turned
on and the device will give out IP addresses directly when a computer is connected to the LAN ports. No additional
setup has to be done.
QIG for WLAN-64GM, WLAN-128GM
3.2 Initial Setup in the Web UI.
Input 192.168.10.1 into the browser, when this the first the time setup the Setup Wizard will start.
Enter your own new Username and Password to start using the Wireless controller
3.3 Wizard
Continue with the Wizard or press Skip to go directly to the Home Page of the Wireless Controller.

-4-
QIG for WLAN-64GM, WLAN-128GM
3.4 Wizard Wireless
The settings which are
entered in this field will be
used as the default
template for all the Access
Points which will be
connected to the Wireless
Controller. Select Enable or
Disable the wireless status,
Enter your SSID name and
wireless encryption.
3.5 Wizard Network WAN
For the WAN setup select
the Internet Access type
for your connection, this
can be DHCP, Static IP,
PPPoE or Bypass. Or press
Scanning Access Mode to
automatically select the
Internet Access.
3.6 Wizard Network LAN
Change the LAN IP
address of the Wireless
Controller as well as the
Start and End IP Address
range and the DNS.
3.7 Wizard Network Other
The Wireless Controller
can automatically reboot
on a fixed time. Select to
Enable or Disable this
function. After this select
the Reboot Time and the
Reboot Interval.

-5-
QIG for WLAN-64GM, WLAN-128GM
3.8 Starting Setup in the Web UI.
It is easy to configure and manage the Wireless Controller with a web browser. Input 192.168.10.1 into the browser (
When you changed the default IP address of the Wireless Controller in the Wizard, please use your new IP Address),
When the Wireless Controller has been setup using the Wizard enter your own new Username and Password.
When you clicked Skip in the Wizard setup, you would go directly to the Home Page of the Wireless Controller but
with the next login the main login page as below will be shown.
To change the language settings from English to Spanish click on the “˅" to open the menu.
Chapter 4. Configure the Wireless Controller
4.1 Main Home Page.
The below web GUI and the topology used in this guide uses the WLAN-128GM as an example.
It is easy to configure and manage the Controller with the web browser. The Home Page of the Wireless Controller
shows an overview of the settings and several quick links.
Quick Links
Click on the cog icon to directly go to the settings without going through the menu.
Click on the Blue, Green, Orange and Red Buttons to go direct to these settings, without going through the menu.

The Home page includes the following fields:
-6-
Object
Description
Throughput
Shows the current status of the WAN port UP and Downstream graph
LAN
Shows the current LAN status and IP information
WAN
Shows the current WAN status and IP information
Device Position
You can enter the device description.
Memory
Current % of internal memory in use
CPU
Current CPU load
Version
Shows the current device firmware version.
QIG for WLAN-64GM, WLAN-128GM
4.3 Device –AP List
AP list will show all the Access Points which are connected to the Wireless Controller. The Access Points will
automatically appear when they are set to on “Get IP from AC” in their webGUI. When multiple different models of
Access Points have been added they can be separated by model or by online/ offline devices.
By default, All Models are shown, click on the All Models button and a single model can be selected, now only Access
Points of the same model will be shown. Click on All Device to choose between Online and Offline device.
To search a selected Access Point enter it’s IP or MAC Address in the search field and the device will be displayed.
4.4 More information
For more information on the detailed settings of the AirLive Wireless Controllers please see the Userguide.
The Userguide can be downloaded from the AirLive website www.airlive.com