airquee Last One Standing Operating instructions

Page 1of 16
Contents
1. Site Survey........................................................................................ 2
2. Included with your Last One Standing............................................... 3
3. Intended use of product .................................................................... 3
4. Operating guidelines......................................................................... 3
5. Troubleshooting................................................................................ 4
6. Hazards relating to electrical equipment ........................................... 5
7. Set-up............................................................................................... 5
7.1 Assembly of the mechanism..................................................... 6
7.2 Add the sealed arms ................................................................ 9
7.3 The Hand-Held Fan.................................................................. 9
7.4 The Control Panel ....................................................................11
7.5 The Bed ..................................................................................12
8. Transporting/Storing the Unit ............................................................14
9. Routine inspections, Trial Operations and Thorough Examinations ..14
8.1 Routine Inspections...................................................................14
8.2 Trial runs...................................................................................14
8.3 Thorough examination...............................................................14
10. Lubrication .....................................................................................15
11. Spare Parts Codes .........................................................................15

Page 2of 16
Last One Standing
(with 2 arms different levels - removable and changeable arms)
IMPORTANT
AS OWNER/OPERATOR IT IS YOUR RESPONSIBILITY TO WRITE AND CARRY OUT
YOUR OWN RISK ASSESSMENT BEFORE ATTEMPTING TO USE THIS PRODUCT.
1. Site survey:
1. Carry out a survey of the area where the Last One Standing will be located, and
check for any overhead/underground cables. It’s important that this is carried out
to avoid ground anchors penetrating underground services, and the Last One
Standing coming into contact with overhead cables when inflated.
2. You should provide an adequate power supply to the fan, this should adhere to
your local power regulations.
3. Check wind speed: It is not allowed to use an inflatable by a higher wind force
than force 5 on the Beaufort scale of 28 - 38 kmph (19-24 mph). Force 5 is a fresh
breeze when small trees in leaf begin to sway.
2. Included with your Last One Standing:
The bed
in its bag
Anchor Pegs
Podiums
Repair Kit
Land Operation
Manual
x8
Toolkit
Control Panel The Mechanism

Page 3of 16
3x
Extra equipment needed in addition what is supplied with your inflatable:
•Suitable 220-240v, 50Hz, single phase electricity to operate the fan.
CAUTION! Precautions should be taken during handling and use of the
product to prevent electric shock. The blower requires a Ground Fault
Protected Circuit (GFCI). Please read the manufacturer’s Instruction
Manual before using the blower(s).
Extra equipment you could consider for your new inflatable:
•Ground sheet to protect the underside of your inflatable
•Sandbag covers to anchor your inflatable indoors
•Sack truck to move your inflatable safely
•RCD to attach to your extension lead
•Crash Mats
This inflatable can be set up and packed away by 3 persons who have
had proper manual handling training and use the correct equipment to
move the inflatable.
3. Intended use of the product:
Different setups of the mechanism:
- The Last One Standing is designed to be used by
up to eight players and one operator. The players must
bounce and duck at the right time to avoid the rotating
sealed arms. The operator has control (via the supplied
control box) over the speed and direction of the arms to
make the game harder or easier as required. If a user is
knocked over by the arms, they should exit the game. The
last player standing is the winner.
- The game can be used with 1 arm, 2 arms same
level or 2 arms different levels. Please see below.

Page 4of 16
How not to use the mechanism:
UNDER NO CIRCUMSTANCES SHOULD YOU EVER USE THE MECHANISM WITH 3 ARMS.
4. Operating guidelines:
- Before entering the game area, CLEAR INSTRUCTIONS SHALL BE GIVEN to players
on their conduct during playtime:
- NO SOMERSAULTS or any ACROBATICS allowed.
- All players remove footwear, eye wear, cell phones, keys, neck wear and/or any
sharp items.
- DO NOT allow the users to OBSTRUCT THE MOVEMENT OF THE ARMS. This
includes no hanging on the arms, pushing-pulling them.
- For safety reasons, users should only stand at the designated jumping space
(numbers, podiums). Do not allow them to get closer to the middle of the bed.
- No one with ANY PRE-EXISTING INJURIES OR HEALTH CONCERNS may use
the “Last One Standing” game.
- Every time a user falls THE MECHANISM MUST BE STOPPED!
- The operator must adjust the speed of the arms to the abilities of the players.
- Use the Emergency Button only in a case of an emergency. After releasing it, WAIT AT
LEAST 5 SECONDS before pressing any other button on the Control Box.
- The MAXIMUM NUMBER OF USERS HAS TO BE RESPECTED at all times.
- The unit should NOT TO BE USED IF IT BECOMES WET. In the event of rain, the unit
should be deflated and folded to prevent water collecting on it.
- The Emergency Stop button MUST ALWAYS BE DEPRESSED AND THE KEY
REMOVED whenever you are setting up the ride or leaving the control console
unattended.
- Do not press more than one button at a time.
- If the arms are OBSTRUCTED RELEASE the left-right rotation buttons IMMEDIATELY.
- Never install and use the 2 arms on the same side of the Middle Bar.
For a more detailed guide on how to operate the mechanism more safely please read the attached
general risk assessment.

Page 5of 16
5. Troubleshooting:
Inside the control box there is a motion controller manufactured by Yaskawa. This electronic
part is responsible for the motion of the sealed arms. Any incorrect usage of the mechanism could
result in Yaskawa producing an Error Code, which means the mechanism stops responding to
the operator’s commands.
Most of these error codes are built in safety mechanisms, protecting the electric motor. When
experiencing this sudden stop, our advice is to follow these simple steps:
- Turn the mechanism OFF, then ON with the Main On/Off key. This will reset the
Yaskawa settings and you should be able to resume playing.
- If that doesn’t help, unlock the top of the Control Box with the supplied triangle key, and
reset the settings manually by pressing the RESET button. (see figure below)
CAUTION! TAKE EXTRA CARE WHEN OPENING THE CONTROL BOX.
DO NOT TOUCH ANYTHING ELSE BESIDES THE RESET BUTTON.
If you still have issues with the mechanism, please contact Airquee customer support on the
following number [phone].
To avoid getting an error code:
- Make sure the electric power supply is stable and not fluctuating in any way.
- Make sure all the cables are connected properly: the motor with the control box, and the
control box to the main electric supply.
Issue
Steps to take
Short circuit or ground fault
on the drive output side:
Try connecting the motor directly to the main supply. In case it is
used with an extension cord, make sure not to connect to many
things to the same extension lead.
The motor is operated at low
speed with heavy load:
Make sure you remove the obstacle from the motor that keeps it
stopping. Please note you are not allowed to add anything to the
middle foam of the mechanism. Make sure that when a player is
on the sealed arm the mechanism is stopped and is not moving
forward.
Cycle times of acceleration
/deceleration:
If you are sure thatthis isthe case, and we would need to change
the values, please contact [e-mail] for further
assistance.
Overvoltage:
The motor will give an error code if the input voltage is too high.
Make sure you change the generator to a smaller one.

Page 6of 16
x4
x4
x4
x2
6. Hazards relating to electrical equipment:
The use of portable electrical equipment involves the potential risk of electric shock, burns or
fire. Before attempting to use the mechanism always check the efficiency of the grounding of the
used electric circuit with a device made for this exact purpose. A decent grounding will absorb all
available electric charge.
A major cause of accidents is failure to maintain equipment. The risk can be managed effectively
if sensible and appropriate rules for use and maintenance are applied!
1. The most important rule when handling the mechanism is to ALWAYS DISCONNECT IT
from its power source when assembling the unit, opening the Control Box or the Drive
Motor. (the only case when this doesn’t apply is when you manually reset the Yaskawa).
2. The control box and the wiring used within the game are NOT WATER PROOF OR
WATER RESISTANT, therefore we do not recommend operating the unit in the rain.
Using electrical equipment in wet or damp conditions can be dangerous. If you suspect
water has entered any of the electrical components they should not be used until
completely dry and tested. We recommend taking professional advice where necessary.
3. All cables and electrical equipment must be tested in accordance with the regulations of
your country.
4. In accordance with HSE guidelines, all 240v equipment should be protected with an RCD
(Residual Current Device) having a maximum trip current of 30 mA. RCD’s are available
from Airquee or your electrical store.
Whenusing it with a generator, make sure it has an output of more than 4 kVA (kilo-volt-ampere),
and a stable 230 Volts on 50Hz.
7. Set-up
CAUTION! MAKE SURE THE MECHANISM IS NOT
CONNECTED TO A POWER SOURCE BEFORE ASSEMBLING IT!
7.1 Assembly of the mechanism (AQ5028SP2)
The mechanism consists of:
Sealed Tubes
with PVC cover
Drive Motor
Legs with
Covers
Arms Covers
Middle Bar
Foam Cover
AP2963
AP2786
MP0003, AP3151
AP3150
Arms
Middle Bar
Wheels
Drive Motor
Foam Cover
Bed Cover
MP0049
MP0055
MP0004
AP3149
x2

Page 7of 16
- Please add the Foam Cover to the Drive
Motor, then insert the wheels and fix them
with the supplied bolts.
- You may move the Drive Motor to the
desired location with the help of the
supplied wheels.
- Exchange the wheels with the legs.
MAKE SURE THE SURFACE
WHERE YOU PLACE THE
MECHANISM IS LEVEL.
- Insert the Middle Bar into the Drive Motor’s shaft and tighten the bolts at the desired
height. We recommend the second and third holes at least. MAKE SURE BOTH BOLTS
ARE ACTUALLY INSIDE A HOLE BEFORE TIGHTENING THEM. THIS WAY YOU
PREVENT THE BOLTS SCRATCHING THE MIDDLE BAR.
BED

Page 8of 16
- Connect the 2 arms: insert the arms into their
corresponding hole and use the bolts to
tighten them.
DO NOT OVER TIGHTEN THE BOLTS OF THE
ARMS, SO THEY DO NOT LOSE THEIR FLEXIBILITY.
- Connect the springs with the supplied bolts.
You can adjust the level of the arm
by choosing one of the 4 holes.

Page 9of 16
- The springs have a screw thread, which allows them to be tightened manually.
It will be easier if you loosen the springs before you add the arms to the Middle Bar.
BE AWARE THAT OVERTIGHTENING THE SPRING CAN DAMAGE IT.
- The highlighted bolt regulates the Metal
Arms capability to jump at a certain height.
7.2 Add the Sealed Arms
DO NOT INFLATE THE ARMS BEFORE YOU SLIP IT ON THE ARMS OF THE MECHANISM!
When receiving the unit, the Sealed Arms should
already be inside their covers.
- Slip the Sealed Arms on the arms of the
mechanism, using the highlighted hole.
You may inflate the arms through the valve
with the help of the supplied handpump.
Please don’t forget to fit the cap on the
valve after inflating the arm.
- Bind the cam buckle around the middle bar
and tie the eyelets with the supplied rope.
USE THE
2ND HOLE
TIE THE EYELETS WITH THE ROPE
TIE THE WEEBING CAM BUCKLE
AROUND THE METAL POLE

Page 10 of 16
- The highlighted PVC loop is for pulling
the uninflated sealed arm in its cover.
Make sure it is hidden when using the
LOS. It may harm users when rotating.
AFTER USING THE GAME, DO NOT TAKE THE SEALED ARMS OUT OF THEIR COVERS.
7.3 The Hand-Held Fan
WE SUGGEST TO READ THE USER MANUAL SUPPLIED BY THE
MANUFACTURER OF THE FAN BEFORE ATTEMPTING TO USE IT.
IMPORTANT: DO NOT LEAVE THE SEALED ARM UNATTENDED
WHILE INFLATING/DEFLATING AND DO NOT OVER INFLATE.
- The hand fan comes with an extra adapter for your valve on the sealed arms.
This adaptor has 2 extra plastic pieces that you must take off.
- The recess of the black rubber must face
outwards. This way it surrounds the edge of
the valve and creates an airtight connection.
- Whenconnecting the adaptor to the valve you
must insert and twist.
- Connect one side of the pipe to the fan and add the adaptor to the other side.
THE RECESS OF THE BLACK RUBBER WASHER
SURROUNDS THE EDGE OF THE VALVE

Page 11 of 16
Inflation process:
1. Locate the valve and remove the cap.
2. Connect the pipe to the fan using the hole
marked with “OUT”.
3. Connect the adaptor to the valve.
4. Switch ON the fan and inflate until firm to touch.
5. Place the cap of the valve.
Deflation process:
1. Locate the valve and remove the cap.
2. Connect the adaptor to the valve.
3. Connect the pipe to the hole marked “IN”.
4. Switch on the fan and deflation will begin.
5. Once all of the air has been withdrawn from the inflatable disconnect the fan.
7.4 The Control Panel
The Control Panel consists of:
- You must bolt these 3 parts together to
make it stable.
Control Box
Support Bar
Legs
ON/OFF
Key
Triangle
Key
12M Cable
Part Code:
MP0013
MP0012
MP0056
MP0015
MP0008
ON/OFF BUTTON

Page 12 of 16
The Control Box:
1. 12M Cable electrical output socket.
2. Main On/Off switch. It works only with the supplied keys.
3. Emergency Stop: In case you must stop the mechanism
suddenly.
4. This will light up when the Control Panel is under power,
and the key is turned to ON.
5. You can change the movement direction of the arms.
6. Adjusting the speed of the arms.
7. Key hole to open the Control Box.
8. Main power cable.
The control panel must be placed at the entrance, at an approximate distance of 1.5M, so that
the operator has an unobstructed view of ALL the players.
7.5 The Bed
- Connect the Drive Motor to the Control Panel
with the 12 Meter Cable. You will find the
socket of the Drive Motor inside. Since the
cable has to go underneath the inflated bed
you won’t have another opportunity to place
the cable if you don’t do it now.
- Place the uninflated bed around the
mechanism.
- Start connecting the sandwich Velcro flaps. The easiest way to connect the flaps is to
first patch the lower flap all the way, then cover it with the top Velcro flap.
1
2
3
5
4
3
1
2
4
5
6
7
3
8

Page 13 of 16
- Add the Podiums to the inflated bed taking
into consideration their numbering.
- Use the bed square cover sheet to cover up
the hole between the mechanism and the
bed.
- Add the 4 protective Arm Foam Covers and the Middle Bar Foam Cover.
LOWER PART OF THE SANDWICH VELCRO
END RESULT WHEN INFLATED

Page 14 of 16
- Connect the filler pipe to the fan and secure
it with the cam buckle. You may start
inflating the bed. While inflating, you can
slightly move and adjust the position of the
bed by the anchor points, to perfectly circle
the mechanism.
8. Transporting/Storing the Unit
DURING TRANSPORTATION, THE MECHANICAL PARTS MUST BE PROTECTED!
Store the pallets somewhere safe as this will be needed in order to ship the unit back to us for
its annual testing and also if and when any repairs are neededas our shippers will not collect without
it being securely wrapped and on a pallet.
When packing away the mechanism for shipping or storing, we advise to:
- remove the keys of the control box.
- do not place anything heavy on the control box or on any part of the mechanism.
- make sure the mechanical parts are packed and protected correctly.
- store the mechanism in dry conditions/in a dry place.
- not to remove the sealed arms from its covers.
- leave the bolts and nuts on the mechanism in their corresponding holes.
- dry every part (if for any reason it becomes wet).
9. Routine Inspections, Trial Operations and Thorough Examinations
9.1 Routine inspections (before every use)
After every setup or operation, before opening the game to the public, the controller or his
nominee SHALL PERSONALLY CHECK that the setup of the Last One Standing is correct.

Page 15 of 16
We recommend to check for every criteria written below. The person carrying out the check shall be
sufficiently trained or experienced in the check routines that have to be carried out.
Check that:
- every button is in a working condition on the Control Panel.
- the electrical connection sockets and cables are not chafed nor damaged.
- the Velcro of every cover has a good grip and is not weakened, the covers are
not damaged and no accessible parts of the machinery has sharp edges,
sharp angles or rough surfaces to cause injury, and no openings which can
“trap” parts of the body or clothing.
- the webbing cam buckles of each sealed arm are not damaged, including their
stitching to the sealed arms cover.
- the stitching of the bed and walls do not have tear, rips which could represent
a safety hazard.
- the metal arms and springs don’t have any sign of damage.
- all nuts and bolts are secure and tightened.
- the inflatable bed is securely anchored.
The device shall not be made available to the public until any adjustments or repairs judged to
be necessary as a result of this inspection have been completed.
9.2 Trial runs
Following the check, the controller shall run one or more trial runs without any members of the public
on it, simulating where possible emergency situations to verify particularly that the control system
and the emergency stop works properly. Only NOW ARE THE PLAYERS ALLOWED TO ENTER
THE UNIT.
9.3 Thorough examination
Besides the regular checks, the Last One Standing should be thoroughly examined at
appropriate intervals by a competent person/institute/organization/company.
The intervals between two successive thorough examinations may be governed by existing
national regulations:
10. Lubrication
- The mechanism has only 1 lubrication point.
This bearing has already a sufficient inner
lubrication, but if lubrication is deemed
necessary manual lubrication can be applied
through the hole highlighted on the picture.
BEARING
LUBRICATION
HOLE

Page 16 of 16
11. Spare parts codes
ENJOY AND HAVE FUN!
Airquee reserves the right to change the content of this manual without a prior notice to the customer.
The model of your product and the type and number of your inclusions may differ from the one presented in this manual.
All the pictures and drawings contained in this manual are for illustration purposes only.
This additional manual to be sent only for AQ5028SP2 Version 1.0 11/05/2018