Airwell 18 User manual

OPERATING MANUAL
DC INVERTER
HAD/JAD/DHA Wall Mounted Range
Before using your air-conditioner, please
read this operating instruction carefully
and keep it for future reference.
R410A
Thank you for
purchasing our
Room Air Conditioner.
CONTENT
FEATURES AND FUNCTIONS ........1
PRECAUTIONS................................2
NAME OF EACH PART....................3-5
OPERATION TIPS............................6
PROTECTION MODES....................7
CARE AND MAINTENANCE............8
TROUBLESHOOTING .....................9
EXCEPTION FOR MULTI
SPLIT TYPE .....................................10
ENGLISH
Part No. 4681000420/01
OM HAD/JAD/DHA 2-N.1 GB
Model 18/21/24

INVERTER
VERTICAL AIR SWING
HORIZONTAL AIR SWING
AUTO CHANGE OVER
SLEEP TIME
At the start of operation, a large power is
used to bring the room quickly to the desired
temperature. Afterwards, the unit automatically
switchs to a low power setting for economic and
comfortable operation.
Automatic swing of horizontal louver is in vertical
direction. The louver moves automatically in
upward and downward direction to spread the
conditioned air evenly throughout the room.
Automatic swing of vertical louver is in horizontal
direction. The louver move automatically in right
and left direction to spread the conditioned air
evenly throughout the room.
The operation mode (cooling, dry, heating)
is switched automatically to maintain the set
temperature, and the set temperature is kept
constant at all times.
The Wireless Remote Control Unit allows
convenient control of air conditioner operation.
When the SLEEP button is pressed during
Heating mode, the air conditioner thermostat
setting is gradually lowered during the period of
operation; during cooling mode, the thermostat
setting is gradually raised during the period of
operation, when the set time is reached, the unit
automatically turns off.
BIPOLAR IONIZER makes the air more fresh
and more comfortable, and let you enjoy healthy
life easily.
1.The bipolar ionizer contains an integrated
cleaning and ON/OFF function. The operation is
done by movement of the cleaning pad(see the
sketch below) from left to right and back.
2.There is a flashing diagnostic indicator(LED)
to assure the ion ouput functionality. In case that
the LED is not ashing, the Cleaning Pad has to
be moved once to the right and back to the left
end position for cleaning. The cleaning should
be done in one of the following:
a. The LED stops ashing(check that the
cleaning pad is on the left which is close to
the LED position).
b. At the maintencance of your equipment.
3. Movement of the cleaning pad from left side
to right will switch the bipolar ionizer OFF
Important Notice: When the air-conditioner is
turned OFF or if the indoor fan stops operation,
the IONIZER stops automatically.
Indoor Outdoor
Cooling
Heating
Upper Limit
Lower Limit
Upper Limit
Lower Limit
32 23 46 NA
21 15 -10 NA
27 NA 24 18
10 NA -15 -16
BIPOLAR IONIZER(Option)
Cleaning Pad
Diagnostic indicator (LED)
Bipolar ionizer sketch
DB[°C]
WB[°C]
DB[°C]
WB[°C]

Do not attempt to install this air conditioner by
yourself.
This unit contains no user-serviceable parts.
Always consult authorized service personnel
for repairs.
When moving, consult authorized service
personnel for disconnection and installation of
the unit.
Do not become excessively chilled by staying
for lengthy periods in the direct cooling airow.
Do not insert ngers or objects into the outlet
port or intake grilles.
Do not start and stop air conditioner operation
by disconnecting the power supply cord and
so on.
Take care not to damage the power supply
cord.
In the event of a malfunction (burning smell,
etc.), immediately stop operation, disconnect
the power supply plug, and consult authorized
service personnel.
If the power supply cord of this appliance is
damaged, it should only be replaced by the
authorized service personal, since special
purpose tools and specied cord are required.
Provide occasional ventilation during use,
Do not direct air ow at replaces or heating
apparatus.
Do not climb on, or place objects on, the air
conditioner.
Do not hang objects form the indoor unit.
Do not set ower vases or water containers on
top of air conditioners.
Do not expose the air conditioner directly to
water.
Do not pull power supply cord.
Turn off power source when not using the unit
for extended periods.
Check the condition of the installation stand
for damage.
Do not place animals or plants in the direct
path of the air ow.
Do not drink the water drained from the air
conditioner.
Do not use in applications involving the
storage of foods, plants or animals, precision
equipment, or art works.
Connection valves become hot during
Heating; handle with care.
Do not apply any heavy pressure to radiator
ns.
Operate only with air lters installed.
Do not block or cover the intake grille and
outlet port.
Ensure that any electronic equipment is at
least one metre away from either the indoor or
outdoor units.
Avoid installing the air conditioner near a
replace or other heating apparatus.
When installing the indoor and outdoor unit,
take precautions to prevent access to infants.
Do not use inflammable gases near the air
conditioner.

Part names and function
ABipolar ionizer LED
There is a flashing LED to assure
the ion output functionality.
In case that the LED is not flashing,
the cleaning pad has to be moved
once to another side and back to
the original position (close to the LED)
for cleaning.
B Bipolar ionizer cleaning pad
The cleaning pad not only have the
cleaning function, but also it can switch
the ionizer ON/OFF.
Position 1(Close to LED): ON
Position 2(Far away from LED): OFF
CStandby indicator
This indicator will light up when the unit
is on Standby. It will turn off when unit is
in operation.
DBipolar ionizer indicator
The indicator will light up when Bi-Polar
ionizer is activated via remote control. It
will light up for about 15 seconds before
goes off. (only applicable to units fitted
with Bi-Polar Ionizer)
ETimer indicator
The indicator will light up when Timer
or Sleep operation is activated. During
this mode, upon receiving any signal
from Remote Control (RC), the light
will come up strong and deemed after
about 15 seconds.
F Filter indicator
If the indicator light up (for about 30
seconds after display is going off), it
means that filter should be cleaned.
The indicator will light up again every
time a signal is received from RC, until
it is reset. To reset the filter indicator,
press the reset button (J) and release
Air intake grill
Air lter
Air purifying lter
Horizontal Louver
Vertical Louver
Bipolar Ionizer (option)
On unit operation (Button/indicator)
Unit`s indicatiors
Power cord (optional)

Infra-Red (IR) receiver
Receive signal from the Remote Controller(RC).
MODE/RESET Button
This is a multi-function button.
RESET Button
When Filter indicator is on, press to turn off
the filter indicator and reset the filter counter.
When Filter indicator is off, press to cancel
the buzzer announcer.
MODE BUTTON
This button can be turned on for cooling
or heating, or turned off without remote
controller. every short pressing, the next
operation mode is selected, in this order:Cool
Mode→Heat Mode→standby→. If button is
pressed long, the system enters diagnostic
mode.
Cooling indicator
Lights up only when MODE Button(N) is
pressed in cooling status.
Heating indicator
Lights up only when MODE Button(N) is
pressed in heating status.
Mode Function:
As long as the lter indicator is off, this button
functions as MODE Button. This button
can be turned on for cooling or heating,
or turn off without remote controller. Every
short pressing, the next operation mode is
selected, in this order: Cool Mode → Heat
Mode → Standby → .
If buttom is pressed long, the system enters
diagnostic mode.
Reset Function:
When Filter indicator is on, the button
functions as RESET Button. Short pressing
and release quickly, turns off the lter
indicator and reset the lter counter.
quickly. The indicator will light up for about 2
seconds and off, indicating the filter indicator
had been reset.
Temperature indicator
This indicator indicate the set point
temperature (SPT). During operation mode,
upon receiving any signal from Remote
Control (RC), the SPT will be displayed for
15 seconds before it goes off.
COOL indicator
The indicator will light up if the operation
mode is set to "COOL", "DRY" or "AUTO".
After around 15 seconds, the indicator will
be deemed. Upon receiving any signal
from Remote Controller (RC), the light will
come up strong and deemed after about 15
seconds.
IHEAT indicator
The indicator will light up if the operation
mode is set to "HEAT". After around 15
seconds, the icon will be deemed. Upon
receiving any signal from Remote Controller
(RC), the light will come up strong and
deemed after about 15 seconds.
J Fan Speed indicator
The indoor fan speed set by user will be
indicated as below:
a) Low
b) Medium
c) High
d) Strong
e) Auto
L
G
H
K
M
N
O
P

7
peration, the unit may perform outdoor coil
High outdoor
temperature.

8
HOW TO CLEAN THE FLAT PANEL
The at panel must be cleaned by soft cloth with water or
mild cleanser. Avoid using abrasive or corrosive cleaner.
Never apply any chemical for cleaning.
HOW TO REMOVE THE PANEL
Open the front panel and push it to the right, then pull out
the right crank, and then pull the front panel to the left and
take it out from the front frame.
CLEANING THE FILTER
Your air conditioner is provided with a lter cleaning
indicator. When the indicator lights up, the lters should
be removed for cleaning.
To remove the air lters, lift up the panel, push the air
lters up slightly to unlock them. Pull out the lters,
clean the lter by washing in warm soapy water and dry
thoroughly, align and t the lters in place, close the panel
by pushing it in the center to lock it in place.
RESET button to turn off indicator.
DO NOT OPERATE THE UNIT WITHOUT FILTERS!
1
Protect the indoor unit from direct sun or lighting.

9