Aiwa Cx-bk33 User manual

SERVICE MANUAL

Amplifier section

European models:

DIN power output (rated): 100 + 100 W

(6 ohms at 1 kHz, DIN)

Continuous RMS power output (reference):

120 + 120 W

(6 ohms at 1 kHz, 10%

THD)

Music power output (reference):

235 + 235 watts (6 ohms at

1kHz, 10% THD)

Other models:

The following measured at 120, 220 – 230, 240 V AC,

50/60 Hz

DIN power output (rated): 140 + 140 W

(6 ohms at 1 kHz, DIN)

Continuous RMS power output (reference):

180 + 180 W

(6 ohms at 1 kHz, 10%

THD)

Inputs

MD (AUX) IN L/R (phono jacks):

Sensitivity 1 V,

impedance 47 kilohms

LINE IN AUDIO L/R (phono jacks):

Vo ltage 250 mV,

impedance 47 kilohms

LINE IN VIDEO (phono jack):

1Vp-p, 75 ohms

MIC (phone jack) (Latin American model only):

Sensitivity 1 mV,

impedance 10 kilohms

Outputs

PHONES (stereo mini jack):

Accepts headphones with

an impedance of 32 ohms

or more

SPEAKER: Accepts impedance of

6 ohms

MD (AUX) OUT L/R (phono jacks):

Voltage 250 mV,

impedance 1 kilohm

VIDEO OUT (phono jack):Max. output level 1Vp-p,

unbalanced, Sync

negative, load impedance

75 ohms

DIGITAL OUT (European and Russian models only):

Sampling frequencies:

44.1 kHz

Wavelength: 660 nm

CD player section

System Compact disc and digital

audio system

Laser Semiconductor laser

(λ=795 nm)

Emission duration:

continuous

Frequency response 2 Hz – 20 kHz

Signal-to-noise ratio More than 90 dB

Dynamic range More than 90 dB

Tape deck section

Recording system 4-track 2-channel stereo

Frequency response 100 – 10,000 Hz, using

Sony TYPE I cassettes

Tuner section

FM stereo, FM/AM superheterodyne tuner

FM tuner section

Tuning range 87.5 – 108.0 MHz

(50-kHz step)

Antenna FM lead antenna

Antenna terminals 75 ohms unbalanced

Intermediate frequency 10.7 MHz

AM tuner section

Tuning range

European models: 531 – 1,602 kHz

(with the tuning interval

set at 9 kHz)

Other models: 530 – 1,710 kHz

(with the tuning interval

set at 10 kHz)

531 – 1,710 kHz

(with the tuning interval

set at 9 kHz)

Antenna AM loop antenna, external

antenna terminal

Intermediate frequency 450 kHz

COMPACT DISC DECK RECEIVER

AEP Model

UK Model

E Model

CX-BK33

Ver 1.0 2004.05

SPECIFICATIONS

– Continued on next page –

9-877-873-01

2004E05-1

Sony Corporation

Home Audio Company

Published by Sony Engineering Corporation

•CX-BK33 is the amplifier, CD player, tape deck

and tuner section in BMZ-K33.

Model Name Using Similar Mechanism NEW

CD Section CD Mechanism Type CDM69BV-30CBD64NS

Base Unit Name BU-30CBD64NS

Optical Pick-up Name A-MAX.3

TAPE Section Model Name Using Similar Mechanism CX-BK1

Tape Transport Mechanism Type CMAL1Z241A

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

This appliance is classified as

a CLASS 1 LASER product.

The CLASS 1 LASER

PRODUCT MARKING is

located on the rear exterior.

The following caution label is located inside the

apparatus.

General

Power requirements

European models: 230 V AC, 50/60 Hz

Other models: 120, 220 – 230, 240 V AC,

50/60 Hz

Adjustable with voltage

selector

Power consumption

European models: 130 W

0.3 W (in Power Saving

mode)

Other models: 155 W

0.3 W (in Power Saving

mode)

Dimensions (w/h/d) incl. projecting parts and controls

Amplifier/Tuner/Tape/CD section:

Approx. 207 ×391 ×

439 mm

Mass

European models: Approx. 9.0 kg

Other models: Approx. 10.3 kg

Design and specifications are subject to change

without notice

Notes on chip component replacement

•Never reuse a disconnected chip component.

•Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing

•Keep the temperature of the soldering iron around 270 ˚C

during repairing.

•Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).

•Be careful not to apply force on the conductor when soldering

or unsoldering.

CAUTION

Use of controls or adjustments or performance of procedures

otherthan thosespecifiedhereinmay result inhazardous radiation

exposure.

UNLEADED SOLDER

Boards requiring use of unleaded solder are printed with the lead-

free mark (LF) indicating the solder contains no lead.

(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARK

Unleaded solder has the following characteristics.

•Unleaded solder melts at a temperature about 40 °C higher

than ordinary solder.

Ordinary soldering irons can be used but the iron tip has to be

applied to the solder joint for a slightly longer time.

Soldering irons using a temperature regulator should be set to

about 350 °C.

Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!

•Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)

than ordinary solder so use caution not to let solder bridges

occur such as on IC pins, etc.

•Usable with ordinary solder

It is best to use only unleaded solder but unleaded solder may

also be added to ordinary solder.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN

THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.

REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE

PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR

IN SUPPLEMENTS PUBLISHED BY SONY.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

You can play back the following discs on this

system. Other discs cannot be played back.

List of playable discs

Discs that this system cannot

play

•An8 cm disc

•An8 cm disc converted to a standard disc

using an adaptor

•CD-ROMs

•CD-Rs/CD-RWs other than those recorded in

the following formats:

–music CD format

–MP3format that conforms to ISO9660

Level 1/Level 2, Joliet or Multi Session

•Adiscthat has a non-standard shape (e.g.,

card, heart).

•Adiscwithpaper or stickers on it.

•Adisc that has the adhesive, cellophane tape,

or a sticker still left on it.

ISO9660 Format

The most common international standard for the

logical format of files and folders on a CD-ROM.

There are several specification levels. In Level 1,

file names must be in the 8.3 format (no more than

eight characters in the name, no more than three

characters in the extension “.MP3”) and in capital

letters. Folder names can be no longer than eight

characters. There can be no more than eight nested

folder levels. Level 2 specifications allow file

names and folder names up to 31 characters long.

Each folder can have up to 8 trees.

For Joliet in the expansion format (file and folder

names can have up to 32 characters), make sure of

the contents of the writing software, etc.

Multi Session

This is a recording method that enables adding of

data using the Track-At-Once method.

Conventional CDs begin at a CD control area called

the Lead-in and end at an area called Lead-out. A

Multi Session CD is a CD having multiple sessions,

with each segment from Lead-in to Lead-out

regarded as a single session.

Playable discs

Format of discs Disc logo

Audio CDs

CD-R/CD-RW

(audio data/MP3 files)

Notes on CD-R and CD-RW

•SomeCD-Rs or CD-RWs cannot be played

on this system depending upon the recording

quality or physical condition of the disc, or

the characteristics of the recording device.

Furthermore,thediscwillnotplayifithas not

been correctly finalized. For more

information, see the operating instructions for

the recording device.

•Discsrecorded on CD-R/CD-RW drives may

not be played back because of scratches, dirt,

recording condition or the driver’s

characteristics.

•CD-RandCD-RW discs recorded in multi-

session that have not ended by “closing the

session” are not supported.

•Thesystem may be unable to play MP3

format files that do not have the “.MP3”

extension.

•Attempting to play non-MP3 format files that

havethe“.MP3”extensionmayresultinnoise

or malfunction.

•Withformats other than ISO9660 level 1 and

2, folder names or file names may not be

displayed correctly.

•Thefollowing discs take a longer time to start

playback.

–adiscrecorded with complicated tree

structure.

–adisc recorded in Multi Session.

–adisctowhich data can be added (non-

finalized disc).

Music discs encoded with

technologies

This product is designed to playback discs that

conform to the Compact Disc (CD) standard.

Recently, various music discs encoded with

by some record companies. Please be aware that

among those discs, there are some that do not

conform to the CD standard and may not be

playable by this product.

Cautions when playing a disc

that is recorded in Multi

Session

•Ifthediscbegins with a CD-DA session, it is

recognized as a CD-DA (audio) disc, and only

the first session will be played back.

•Ifthe disc begins with an MP3 session, it is

recognized as an MP3 disc, and playback

continues until a CD-DA (audio) session is

encountered.

•Theplayback range of an MP3 disc is

determined by the tree structure of files

produced by analyzing of the disc.

•Adiscwitha mixed CD format will be

recognized as a CD-DA (audio) disc.

•Data part of CD-Extras

•Audiopart of Mixed CDs

CD-Extra: This format records audio (audio CD

data) on the tracks in session 1 and data on the tracks

in session 2.

Mixed CD: This format records data on the first

track and audio (audio CD data) on the second and

subsequent tracks of a session.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 5

2. GENERAL

Location of Controls........................................................ 7

3. DISASSEMBLY

3-1. Disassembly Flow ........................................................... 9

3-2. Side Panel (L)/(R) ........................................................... 10

3-3. Top Panel Block .............................................................. 10

3-4. Front Panel Block ............................................................ 11

3-5. MAIN Board.................................................................... 11

3-6. Rear Panel Block ............................................................. 12

3-7. Tuner (FM/AM)............................................................... 12

3-8. SPEAKER Board ............................................................ 13

3-9. ACDC Board, Power Transformer .................................. 13

3-10. FRONT AMP Board Block ............................................. 14

3-11. CD Mechanism Deck (CDM69BV-30BD64NS) ............ 14

3-12. Base Unit Section (BU-30CBD64NS) ............................ 15

3-13. OP Assy ........................................................................... 15

3-14. SW (1) Board, SW (2) Board, SW (3) Board,

SW (4) Board, Bracket (Top) Assy.................................. 16

3-15. RELAY Board ................................................................. 16

3-16. Motor (Stocker)Assy (Stocker) (M761) ......................... 17

3-17. Motor (Roller) Assy (Roller) (M781).............................. 17

3-18. Motor (Mode) Assy (Mode) (M771) ............................... 18

3-19. Rubber Roller (Slider) Assy ............................................ 18

3-20. Timing Belt (Front/Rear)................................................. 19

3-21. Cam (Gear) ...................................................................... 19

3-22. SENSOR Board ............................................................... 20

3-23. Single Cassette Mechanism (CMAL1Z241A) ................ 20

4. ASSEMBLY

4-1. How To Install The Cam (Ejact Lock) ............................ 21

4-2. How To Install The Cam (Gear) ...................................... 21

4-3. How To Install The Gear (Mode 2) ................................. 22

4-4. How To Install The Gear (Mode Cam)............................ 22

4-5. How To Install The Rotary Encoder (S702),

Gear (Stocker Communication)....................................... 23

4-6. How To Install The Cam (Stocker U/D) .......................... 23

4-7. How To Install The Stocker Assy .................................... 24

4-8. PhaseAdjustment Between Pinions (Slider)

and Slider-1 To 5 (L/R) ................................................... 25

5. TEST MODE ............................................................... 26

6. ELECTRICAL ADJUSTMENTS

DECK Section ................................................................. 28

CD Section ...................................................................... 29

7. DIAGRAMS

7-1. Block Diagram – CD Section – ...................................... 31

7-2. Block Diagram – TUNER/TAPE/USB Section –........... 32

7-3. Block Diagram – AMP Section – ................................... 33

7-4. Block Diagram – POWER SUPPLY Section – .............. 34

7-5. Printed Wiring Board – BD Board – .............................. 36

7-6. Schematic Diagram – BD Board – ................................. 37

7-7. Printed Wirig Boards – CHANGER Section –............... 38

7-8. Schematic Diagram – CHANGER Section – ................. 39

7-9. Printed Wiring Board –DECK Board – .......................... 40

7-10. Schematic Diagram – DECK Board –............................ 41

7-11. Schematic Diagram – MAIN Board (1/4) – ................... 42

7-12. Schematic Diagram – MAIN Board (2/4) – ................... 43

7-13. Schematic Diagram – MAIN Board (3/4) – ................... 44

7-14. Schematic Diagram – MAIN Board (4/4) – ................... 45

7-15. Printed Wiring Board – MAIN Board – ......................... 46

7-16. Printed Wiring Board – FRONTAMP Board – ............. 47

7-17. Schematic Diagram – FRONTAMP Board (1/2) – ....... 48

7-18. Schematic Diagram – FRONTAMP Board (2/2) – ....... 49

7-19. Printed Wiring Board – USB Board – ............................ 50

7-20. Schematic Diagram – USB Board – ............................... 51

7-21. Printed Wiring Board – MIC Board –

(Chirean and Peruvian models) ....................................... 52

7-22. Schematic Diagram – MIC Board –

(Chirean and Peruvian models) ....................................... 53

7-23. Printed Wiring Board – HEADPHONE Board – ........... 54

7-24. Schematic Diagram – HEADPHONE Board – .............. 54

7-25. Printed Wiring Board – SPEAKER Board – .................. 55

7-26. Schematica Diagram – SPEAKER Board – ................... 55

7-27. Printed Wiring Board – LCD Board – ............................ 56

7-28. Schematic Diagram – LCD Board –............................... 57

7-29. Printed Wiring Boards – KEY Section – ........................ 58

7-30. Schematic Diagram – KEY Section – ............................ 59

7-31. Printed Wiring Board – ACDC Board – ......................... 60

7-32. Schematic Diagram – ACDC Board – ............................ 61

7-33. Printed Wiring Board – PT85 Board –

(AEP and UK models)..................................................... 62

7-34. Schematic Diagram – PT85 Board –

(AEP and UK models)..................................................... 63

7-35. Printed Wiring Board – PT96 Board –

(Chirean and Peruvian models) ....................................... 64

7-36. Schematic Diagram – PT96 Board –

(Chirean and Peruvian models) ....................................... 65

8. EXPLODED VIEWS

8-1. Panel Section ................................................................... 78

8-2. Tape Mechanism Deck Section (CMAL1Z241A)........... 79

8-3. Front Boards Section ....................................................... 80

8-4. Front Cabinet Section...................................................... 81

8-5. MAIN Board Section....................................................... 82

8-6. Chassis Section................................................................ 83

8-7. CD Mechanism Deck Section-1

(CDM69BV-30CBD64NS) ............................................. 84

8-8. CD Mechanism Deck Section-2

(CDM69BV-30CBD64NS) ............................................. 85

8-9. CD Mechanism Deck Section-3

(CDM69BV-30CBD64NS) ............................................. 86

8-10. CD Mechanism Deck Section-4

(CDM69BV-30CBD64NS) ............................................. 87

8-11. CD Mechanism Deck Section-5

(CDM69BV-30CBD64NS) ............................................. 88

8-12. CD Mechanism Deck Section-6

(CDM69BV-30CBD64NS) ............................................. 89

8-13. Base Unit Section (BU-30CBD64NS) ............................ 90

9. ELECTRICAL PARTS LIST................................ 91

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

PART No.

SECTION 1

SERVICING NOTES

•MODEL IDENTIFICATION

– Rear Cover –

MODEL PART No.

Chilean and Peruvian models 4-254-166-1[]

AEP and UK models 4-254-166-2[]

The laser diode in the optical pick-up block may suffer electrostatic

break-down because of the potential difference generated by the

charged electrostatic load, etc. on clothing and the human body.

During repair, pay attention to electrostatic break-down and also

use the procedure in the printed matter which is included in the

repair parts.

The flexible board is easily damaged and should be handled with

care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on

the disc reflective surface by the objective lens in the optical pick-

up block. Therefore, when checking the laser diode emission,

observe from more than 30 cm away from the objective lens.

LASER DIODE AND FOCUS SEARCH OPERATION

CHECK

Carry out the “S curve check” in “CDsection adjustment” and check

that the S curve waveforms is output three times.

NOTES ON HANDLING THE OPTICAL PICK-UP

BLOCK OR BASE UNIT

SERVICE POSITION

–Tape Mechanism Deck –

Connect the wire (flat type) (8 core)

to the MAIN board (CN903) and

the mechanism deck.

Connect the wire (flat type) (11 core)

to the DECK board (CN008) and the MAIN board (CN009).

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

Connect the extension jig (J-2501-248-A)

to the REALY board (CN701) and

the MAIN board (CN901).

Connect the extension jig (J-2501-242-A)

to the BD board (CN104) and

the MAIN board (CN507).

Connect the extension jig (J-2501-245-A)

to the BD board (CN102) and

the MAIN board (CN902).

FRONT AMP board

SPEAKER board

PT85/PT96 board

ACDC board

CD mechanism deck

tuner unit

MAIN board

front panel sectio

– CD mechanism deck –

•In checking the CD mechanism deck section, prepare three extension jigs (Part No. J-2501-242-A:1.00 mm 11core/

Part No. J-2501-245-A: 1.00 mm 23 core/Part No. J-2501-248-A: 1.00mm 27 core).

Note: The CD mechanism deck of this model is a vertical type and putting it vertically as shown in the figure is the standard position.

When checking signals such as RF waveforms, operate it with the CD mechanism deck in the standard position as shown below.

– MAIN board and ACDC board –

•For connecting the CD mechanism deck, prepare three extension jigs. (Refer to “– CD mechanism deck –”)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

Main unit

ALBUM +/– ql

BASS control wk

CD SYNC wa

DISC SELECT 1 – 5 4

Disc slot 7

DISPLAY eg

Display window 3

ENTER qa

EQ es

FM MODE 9

FUNCTION ef

i-Bass 2

JOG dial (AMS/TUNING) qs

KARAOKE

LINE IN AUDIO L/R jacks wf

LINE IN VIDEO jack wg

MIC jack

MIC LEVEL

MIDDLE control e;

PHONES jack qg

PLAY MODE 8

REC PAUSE/ START w;

Remote sensor wd

REPEAT 9

Tape deck 5

TREBLE control ea

TUNER/BAND ed

TUNER MEMORY 0

TUNING +/– qk

TUNING MODE 8

USB

USB port wh

VOLUME control wl

?/1 (power) 1

ZPUSH EJECT (eject) 5

Z(eject) 6

X(pause) qd

x(stop) qf

./> (go back/go forward)

m/M (rewind/fast forward)

nN (play) ws

Latin American model only

Except for Latin American

model

ALPHABETICAL ORDER

A – Q R – Z

BUTTON DESCRIPT

12345

12 3 4 56

wd ws wa ql

ef ed

qg qf

w; qk

IONS

SECTION 2

GENERAL

•LOCATION OF CONTROLS

This section is extracted from

instruction manual.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

Remote control

ALBUM + qa

ALBUM – qd

CD qj

CLEAR qg

CLOCK/TIMER SELECT 2

CLOCK/TIMER SET 3

DISC SKIP 0

DISPLAY wa

ENTER 9

EQ qf

FM MODE 4

FUNCTION +/– 56

PLAY MODE w;

REPEAT 4

SLEEP ws

TUNER BAND qk

TUNER MEMORY ql

TUNING MODE w;

VOLUME +/– qs

?/1 (power) 1

m/M (rewind/fast forward)

X(pause) 8

x(stop) 8

N(play) 8

+/– (tuning) qh

./> (go back/go forward)

ALPHABETICAL ORDER

A – E F – Z

BUTTON DESCRIPTIO

ws 1

Use buttons on the remote for the operation.

Press ?/1 to turn on the system.

2Press CLOCK/TIMER SET.

3Press .or >repeatedly to set the

hour.

4Press ENTER.

5Press .or >repeatedly to set the

minute.

6Press ENTER.

The clock starts working.

To adjust the clock

Press CLOCK/TIMER SET.

2Press .or >until “CLOCK SET”

appears, then press ENTER.

3Do the same procedures as step 3 to 6

above.

Notes

•Theclock settings are canceled when you disconnect

the power cord or if a power failure occurs.

•You cannot set the clock in Power Saving Mode.

Setting the clock

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SECTION 3

DISASSEMBLY

3-2. SIDE PANEL (L)/(R)

(Page 10)

3-5. MAIN BOARD

(Page 11)

3-20. TIMING BELT

(FRONT/REAR)

(Page 19)

3-21. CAM (GEAR)

(Page 19)

3-22. SENSOR BOARD

(Page 20)

3-10. FRONT AMP BOARD BLOCK

(Page 14)

3-11. CD MECHANISM DECK

(CDM69BV-30CBD64NS)

(Page 14)

3-12. BASE UNIT SECTION

(BU-30CBD64NS)

(Page 15)

3-14. SW (1) BOARD,

SW (2) BOARD,

SW (3) BOARD,

SW (4) BOARD,

BRACKET (TOP) ASSY

(Page 16)

3-16. MOTOR (STOCKER)

ASSY (STOCKER)

(M761)

(Page 17)

3-15. RELAY BOARD

(Page 16)

3-13. OP ASSY

(Page 15)

3-17. MOTOR (ROLLER)

ASSY (ROLLER)

(M781)

(Page 17)

3-19. RUBBER ROLLER

(SLIDER) ASSY

(Page 18)

3-18. MOTOR (MODE)

ASSY (MODE)

(M771)

(Page 18)

3-7. TUNER (FM/AM)

(Page 12) 3-8. SPEAKER BOARD

(Page 13)

3-4. FRONT PANEL

BLOCK

(Page 11)

3-6. REAR PANEL BLOCK

(Page 12) 3-23. SINGLE CASSETTE

MECHANISM

(CMAL1Z241A)

(Page 20)

3-3. TOP PANEL BLOCK

(Page 10)

3-9. ACDC BOARD, POWER TRANSFORMER

(Page 13)

SET Note 1: The process described in can be performed in any order.

Note 2: Without completing the process described in , the next process can not be performed.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

CX-BK33

Note: Follow the disassembly procedure in the numerical order given.

3-2. SIDE PANEL (L)/(R)

3-3. TOP PANEL BLOCK

side panel (L)

screw

(BVTP3

10)

side panel (R)

screw

(BVTP3

10)

four screws

(case 3 TP2)

four screws

(case 3 TP2)

two wires (flat type)

(11 core: CN009,

8 core: CN903)

screw

(BVTP3

10)

top panel block

Remove the top panel block

in the direction of arrow,

and release three claws.

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Table of contents

Popular Car Receiver manuals by other brands

Linear Series

Linear Series LS5050 Operation and installation manual

Kenwood

Kenwood KRC-160 instruction manual

Sony

Sony XR-CA430X Service manual

T+A Elektroakustik

T+A Elektroakustik K1 CD-RECEIVER operating instructions

SoundMax

SoundMax SM-CDM1052 instruction manual

Xtrons

Xtrons HD107HD user manual

Mopar

Mopar RB3 manual

Clarion

Clarion ADDZEST DMZ615 owner's manual

Sony

Sony XAV-601BT Specifications

PIE

PIE GM12-POD/S Operation manual

Hyundai

Hyundai H-910H instruction manual

Sony

Sony XR-C6100 Service manual

Sony

Sony CDX-L600X - Fm/am Compact Disc Player Installation/connections

Motorola

Motorola VWA63 Service manual

Sound Storm

Sound Storm STM93R user manual

Nextar

Nextar D3201 instruction manual

Alpine

Alpine CDE-163BT owner's manual

Kenwood

Kenwood KDC-X303 quick start guide

Aiwa CX-BK33 User manual

Popular Car Receiver manuals by other brands