Akai CSP-8500 User manual

2-waySpeaker
(CSP-8500/CSP-8600)
Precautions
Do not continuously use the speaker system beyond the peak power
handing capacity.
Keep recorded tapes, watches, and personal credit cards using magnetic
coding away from the speaker system to protect them from damage caused
by the magnets in the speakers.
Please note thee following when installing the units; otherwise malfunction
and/or deterioration in sound quality may result.
-Do not touch the diaphragms and/or speaker cones by hand or with tools.
-Do not put your fingers through the holes of the frame.
If you cannot find an appropriate mounting location, consult your car dealer
or your nearest our company dealer before mounting.
Instructions
Before mounting
A depth of at least CSP-8500 (45mm) , CSP-8600 (45mm) is required to
mount the speaker. Measure the depth of the area where you are to mount the
speaker, a n d ensure that the spe a k e r is not obstructing an y other
components of the car. Keep the followings in mind when choosing a
mounting location:
Make sure that nothing is obstructing around the mounting location of the
door(front or rear) where you are to mount the speaker.
A hole for mounting may already be cut out of the inner panel of the
door(front or rear).In this case, you need to modify the board only.
If your are to mount this speaker system in the door(front or rear),make
sure that the speaker terminals, frame or magnet do not interfere with any
inner parts, such as the window mechanism in the door(when you open or
close the window),etc.
Also make sure that the speaker grille does not touch any inner fittings,
such as the window cranks, door handles, arm rests, door pockets, lamps
or seats etc.
If you are not mount this speaker system in the rear tray, make sure that the
speaker terminals, frame or magnet do not touch any inner parts of the car,
such as the torsion bar springs(when you open or close the trunk lid), etc.
Also make sure that the speaker grille does not touch any inner fittings,
sure as seat belt, head rests, center brake lights, inner covers of the rear
wipers, curtains or air purifiers, etc.
CSP-8600
CSP-8500
ø152 mm ø114 mm ø70.2 mm
44 mm 4.3 mm
22 mm
ø156 mm
ø138 mm
ø4.5 mm
5 mm
ø165.5 mm ø136 mm ø80.3 mm
44 mm 5.8 mm
27 mm
ø171 mm
ø142.2 mm
ø5.1 mm
5.5 mm
www.akai-atd.com
ø159 mm
ø4.9 mm

Part List
CSP-8500 CSP-8600
Mounting from the car interior
DOOR (FRONT / REAR)
1
Mark 4 bolt holes and make them 3.2mm in diameter.
Unit: mm
CSP-8500 : Ø 138 mm
CSP-8600 : Ø 116 mm
Ø 3.2 mm
2
Power amplifier
*Note
When releasing , push
down on the firmly and
release carefully.
If excessive force is used,
damage to the speaker or
terminal cable may result.
Black-Striped cord
1
1
1
3
Specifications
CSP-8500
Speaker Coaxial 2-way
Woofer Φ130mm
Mylar dome tweeter Φ28 mm
Maximum Power 50W
Rated power 25W
Rated impedance 4Ω
Output sound 90dB/W(1m)
pressure level
Effective frequency 50Hz~22KHz
range
Speaker Coaxial 2-way
Woofer Φ158mm
Mylar dome tweeter Φ28 mm
Maximum Power 60W
Rated power 30W
Rated impedance 4Ω
Output sound 91dB/W(1m)
pressure level
Effective frequency 40Hz~22KHz
range
CSP-8600
2
Before install the scew,
please remove first.
2
Http://www.akai-atd.com