Akyga AK-EV-08 User manual

AK-EV-08 - user manual
/ak-ev-08
www.akyga.com
Short description of the product
The product is compatible with the applicable national and European requirements.
What is in the box?
- AK-EV-08 power supply
Symbols explanation:
There is a risk of losing health or life (e.g. by electic shock).
There is a particular danger connected with service.
Important tips and information.
Product accordance with the EU directive 2002/96/EC. The symbol of the crossed out basket
placed on the product means that the marked product can not be disposed of with other
household waste. After use, the product must be return to collection point for used electical and
electronic equipment or to the seller. Appropriate segregation of rubbish for subsequent
processing, recovery or descrution contributes to avoiding negative effects on the environment
and health, and also allows the recovery of raw materials from which the product is made.
p. 1
The CE standard description on the product is the manufacturer's declaration that the marked
product meets the requirements of the directive so-called The "New Approach" of the European
Union (EU). For security and certification (CE) reasons, the device can not be rebuild or change
in any way. In the reason of using the power supply for other purposes than those described,
the product may be demaged. The incorrect use may also cause hazard such as short-circuits,
burns, electric shocks, etc. Read the users manual carefully and keep it for later use. The product
could be share to third partie only with the user manual included.
The Akyga AK-EV-08 power supply is used The device has an endless to charge an custom e-bike.
cable which allows you to choose the plug freely depending on the device being charged. Its maximum
charging power is 60 W, with output parameters of 29.4 V/2 A. A set of protectors OVP, OTP, OPP, SCP,
OCP provides safe and stable work of both power supply and powered device.
The power consumption of powering device can not exceed the power supply nominal current.
The product is adapted to supply voltage in the range of 100-240 V, 50/60 Hz.
e-bike power supplies
The RoHS mark on the product is the manufacturer's declaration that the marked product meets
the requirements of the EU Restriction of Hazardous Substances (2002/95/EC) directive, which
aims to reduce the amount of hazardous substances penetrating into the environment from
electrical and electronic waste.
>80%
EC
BOX
Ecological Solutions
GREEN

AK-EV-08 - user manual
p. 2
Safety Precautions
WARNING! Product heats up during operation. To reduce the risk of burns or overheating the
power supply, do not place it in restricted ventilation area. Also, do not allow the working power
supply to touch soft surface such as pillows, blankets or clothing. The power supply meets the
limits on the surface temperatures available to the user, as defined in the International Standard
for Safety of Information Technology Equipment (IEC 60950).
Connecting e-bike whose demanded power is greather than power of the power supply, can
cause battery failure or even damage (burn) of power supply.
An electrostatic discharge occurs when two object touch each other, for example, an electric
charge that occurs when user touch metal door handle after walking on a carpet. Discharging
electrostatic charges from fingers or other electrostatic conductors can damage electronic
components. To avoid damaging the e-bike, abstain from touching electrical outlets, wires and
electonic circuits. The user’s contact with electronic components should be kept to a minimum.
The II protection class device. It provides protection against electric shock against direct and
indirect contact, and thanks to the additional isolation it is not necessary to connect the device
case with the protective earth conductor.
The device is intended only for domestic use, indoors.
The manufacturer of the product is not responsible for damage or insults caused in effect
of disobey the safety instructions and informations contained in these user manual.
źKeep the product and the packaging out of range of children and animals. The package
includes a foil that child could choke while playing.
źThe product operation in adverse conditions is not allowed. Adverse conditions are primarily:
exposure to direct sunlight, high or very low ambient temperatures, strong vibrations, high
humidity, surrounds of gases, dusts or flammable and aggressive liquids.
źIf the product has been damaged, does not work properly or has been stored for a long period
of time in bad or unfavorable conditions, safe operation of the device is not possible. It is
essential to stop using the product and to protect it against re-use for security purposes.
źIt is forbidden to apply the mechanical load to the product - strong shocks, impacts, dropping
or crushing may cause its damage.
źMake sure that the power cord is not crushed, bent, twisted, rubbed against sharp edges or
mechanically loaded in any other way. Avoid thermal load of the cable - in particular keep away
from heat sources (such as stoves, radiators, fireplaces).
źConnection of the power supply to electricity is done by connecting cable with the IEC C7 plug
(”eight”) to power supply with IEC C8 connector and then connecting appropriate plug to
grounded electrical outlet.
źProduct and power cord should not be touched with moist or wet hands under no
circumstances.
źShort-circuiting the current connection is prohibited.
źBefore connecting the adapter to the mains socket, make sure that the voltage specified on
the power supply matches voltage supplied to the household socket.
źPower cords should be laid in such a way as to eliminate the risk of stumbling or hooking over.
źIts forbidden to modify the power cord. In the case of modifications, the cable may be
damaged, causing threats to life, health and property.
e-bike power supplies

AK-EV-08 - user manual
p. 3
źMains plug should be disconnect from power socket if the product is not in use for a long time.
źIn case of any doubts regarding operation, safety or connection of the product, please contact
the manufacturer or a qualified specialist for this purpose.
źAll maintenance, adjustment and repair work on the product may only be carried out by a
qualified person in a specialist facility.
źWhen disconnecting the power cord from the socket and from the device, do not pull on the
cord, but only on the part of the cable plug provided for this purpose.
Problem
Cause
Solution
A e-bike connected to an
electrical outlet via
power supply does not
work
No mains voltage
źCheck the correct connection of
the power supply to the mains
socket
źCheck the mains fuses
The power supply is
overloaded
źDisconnect the power supply
from the e-bike, check the
correctness of the current
parameters
There is a suspicion of a
product defect
źStop using and contact the
seller
A e-bike connected to an
electrical outlet via
power adapter does not
charge the battery
The power supply does
not correspond to the
current parameters
źContact with seller
źDisconnect the power supply
from battery and check if
current parameters are correct
Removing the most common problems
e-bike power supplies
6. After charging light turn colour to green.
1. Select and connect the appropriate connector to power supply.
3. Make sure that the power adapter has propriet polarisation (+/-) to your e-bike.
4. Connect the power supply connector to the battery.
5. Red lihgt sygnalise charging process.
2. Connect power cord to the electrical socket.
Preparing the Power Supply for Use:
Cleaning the power supply
źUse soft and antistatic cloth for cleaning the power supply.
źDo not use abrasive or chemical cleaners.
Disconect the power supply from the electrical socket and connected devices before cleaning.

AK-EV-08 - user manual
p. 4
Technical specfication
Product manufacturer: Akyga Europe sp. z o.o.
ul. Wrocławska 1c
52-200 Suchy Dwór
e-bike power supplies
Product code:
Supply voltage:
Output voltage and amperage:
Maximum power:
Efficiency:
OVP (over voltage protection) :
OCP (over current protection) :
OPP (overpower protection) :
OTP (over temperaturre protection) :
SCP (short circuit protection) :
Soft start:
Power inlet:
Output connector:
Cable length:
Compilance with standards:
EAN code :
AK-EV-08
100-240 V, 50/60 Hz
29.4 V / 2 A
60 W
>80%
Yes
Yes
Yes
Yes
Yes
Yes
IEC C8
Without termination
1 m
CE, FCC, RoHS
5901720136060