AL’S GARDEN ART ACP User manual

CARE AND MAINTENANCE
•Regular cleaning of the pump may be
necessary depending upon the
environment in which it is operated. Clean
the pump when it is visibly soiled or when
a drop in performance is detected.
•Before cleaning, always disconnect the
pump from the power source.
•Remove all parts from the pump and
clean in warm, soapy water.
•Disassemble the pump housing and
remove the impeller housing to expose
the impeller assembly. Remove the
impeller assembly by gently pulling on the
impeller blades. Use a soft cloth or brush
to clean the impeller assembly and the
inside of the impeller housing.
TROUBLESHOOTING
If the pump fails to operate:
•Check to make sure the power cord is
plugged in and the pump is getting
power.
•Check the pump outlet and any
tubing, fountains, spitters etc. for
kinks or obstructions.
•Remove the inlet screen and/or pump
cover, and impeller housing to expose
the impeller. Turn the impeller to
ensure that it is not broken or
jammed.
If the performance of the pump is not
satisfactory or the pump does not flow evenly:
•Check to make sure the pump is
completely submerged in water.
•Check to make sure the impeller and
the housing are clean.
•Adjust flow control.
REPLACEMENT PARTS LIST
Part Description
A Pump (not shown)
B Screen
C Impeller housing
D O-ring
E Adapter
For replacement parts, contact our customer
service department at 909-424-0221.
8 am – 4:30 pm PST, Monday through Friday.
Submersible
Fountain Pump
3600 Gallons per Hour
model ACP
ACP-50
PACKAGE
CONTENTS
Part ACP
Description Pump
Quantity 1
D
C
E
B
Questions, problems, missing parts?
Before returning to your retailer, contact ou
r
customer service department at 909 424-0221
8 am – 4:30 pm, PST, Monday - Friday, or
e-mail us at [email protected]
AL’S GARDEN ART
Manufacturers of cast stone fountains an
d
statuary since 1949, family owned an
d
operated with more then half a century o
f
skill and passion for creating top quality cas
t
stone art.
P.O. Box 111 •Colton, CA 92324
www.alsgardenart.com

WARNINGS AND CAUTIONS
WARNING
• Risk of electrical shock. This pump is
supplied with a grounding conductor and
grounding–type attachment plug. To
reduce the risk of electric shock, be
certain that it is connected only to a
properly grounded, grounding- type
receptacle (GFCI).
• Do not exceed the voltage shown on the
pump.
• Always disconnect pump from the power
source before beginning any maintenance
or work on the pump.
• Inspect cord for damage before
installation and/or maintenance. Replace
the entire pump assembly if damage is
found.
• Do not remove the grounding pin from the
power cord plug.
• Risk of electrical shock – This pump has
not been investigated for use in swimming
pool or marine areas.
CAUTION
• This pump has been evaluated for use
with water only.
• Use a proper power source as indicated
on the pump label.
• Keep the cord away from high
temperatures or other heat sources.
• Avoid using the pump when water
temperatures fall below 41° F.
• Do not use the pump in water exceeding
86° F.
• Do not pump heated liquids.
• Do not let the pump run dry. Pump must
be completely submerged for proper
operation and cooling.
WARNINGS AND CAUTIONS (Cont’d)
• Operate in freshwater only. Avoid heavily
chlorinated water and water with high pH
levels.
• Do not lift the pump by its power cord.
PREPARATION
Before beginning assembly or operation of
product, make sure all parts are present.
Compare parts with package contents list on
the cover and diagram on the reverse side of
this document. If any part is missing or
damaged, do not attempt to assemble, install
or operate the product. Contact customer
service for replacement parts.
•Estimated Assembly Time: 5 minutes
•No tools required for assembly.
WARRANTY
This warranty is offered to you as an extra
benefit and does not affect your rights as a
consumer in any way. This unit has been
checked for compliance to performance
requirements at the time of manufacture and
are made in accordance with the
requirements set forth in UL778 to insure safe
operations over the life of the product. This
pump is warranted against manufactured
defect for one (1) year from the date of
purchase. Proof of purchase is required for all
warranty claims. The warranty is not valid if
defects are caused by tampering, negligence,
misuse or not observing safety warnings. No
responsibility is assumed for indirect damage
that may result from the use of this appliance.
ASSEMBLY INSTRUCTIONS
1. Connect tubing to the outlet of the pump.
Fig 1
NOTE: Tubing is NOT INCLUDED
2. Place the pump into the water and
connect to a proper power source.
Fig. 2
Adapter
Tubing
Fig. 1
Fig. 2