Alarmcom ADC-T3000 User manual

Operate the Alarm.com Smart hermostat
he Alarm.com Smart hermostat (ADC- 3000 and ADC- 2000) can be operated locally in addition to the remote
control features on the Customer Website and app.
To locally operate the ADC-T3000:
Waking the device
1. Press any button to wake the thermostat up.
Note: he ADC- 3000 display cannot stay on permanently, but it can be configured to wake when motion is
detected nearby. For more information about enabling motion-detected wake, see Enable or disable motion-
detected wake on an Alarm.com Smart hermostat (ADC- 3000).
2. After waking, the display will show the current mode, room temperature, and setpoint.
https://answers.alarm.com/ADC/Partner/Installation_and_ roubleshooting/ hermostats/Alarm.com_Smart_ hermostat_(ADC-…
Updated: Mon, 20 Apr 2020 19:39:44 GM
1

Changing the mode and setpoint
1. Press the button.
2. Select MODE.
◦ he modes are HEA , COOL, AU O, EMER, and OFF.
◦ he thermostat will only show the modes that are available based on the system configuration.
◦ When in EMER mode, the thermostat will flash EMER when the display wakes up, and it will show HEA at
the top of the screen. Changing the mode will leave EMER mode.
3. Select the desired mode.
4. Once in the desired mode, press the and buttons to adjust the desired setpoint.
◦ In AU O mode when the system is idle, the screen will display AU O. he thermostat will display HEA ING
when calling for heat and COOLING when calling for cool.
Changing the fan mode
1. Press the button.
2. Select the FAN MODE option.
◦ he fan modes are AU O, ON, and CIRCULA E. he thermostat will only show the fan modes if it has been
configured to control a fan.
◦ AU O mode will automatically turn the fan on when your system is either heating or cooling.
◦ CIRCULA E will turn the fan on for 15 minutes every hour by default. he duration for CIRCULA E can be
configured from the online account.
To locally operate the ADC-T2000:
1. Press any button to wake the thermostat up.
Note: o configure the thermostat display to always be on, see Can the Alarm.com Smart hermostat display stay
on permanently?.
https://answers.alarm.com/ADC/Partner/Installation_and_ roubleshooting/ hermostats/Alarm.com_Smart_ hermostat_(ADC-…
Updated: Mon, 20 Apr 2020 19:39:44 GM
2

2. After waking, the display will show the current mode and room temperature.
3. Press or once to display the current setpoint.
◦ he mode icon HEA or COOL will begin to pulse.
4. Press or again to adjust to the desired set point.
5. Press at any time to change the mode.
◦ he modes are HEA , COOL, AU O, EMER, and OFF.
◦ EMER mode is available for Heat Pump systems. Press and hold while in Heat Mode to enter EMER.
◦ When in EMER mode, the display will read EMER when the thermostat wakes up and the HEA icon will be
displayed. Changing the mode will leave EMER mode.
• In AU O, the brighter icon will indicate which setpoint is currently displayed and active HEA or COOL.
• After 5 seconds the display will return to the current room temperature. he mode icon will become solid to indicate
this. If powered by the “C” wire, the thermostat display will remain lit. If the thermostat is running on battery power
only, the display will turn off after 5 seconds to conserve energy. he thermostat will continue to operate while the
display is off.
https://answers.alarm.com/ADC/Partner/Installation_and_ roubleshooting/ hermostats/Alarm.com_Smart_ hermostat_(ADC-…
Updated: Mon, 20 Apr 2020 19:39:44 GM
3